Használati útmutató Atdec TH-3070-UF flat panel wall mount

Atdec Lapos panel támogatás TH-3070-UF flat panel wall mount

Olvassa el alább 📖 a magyar nyelvű használati útmutatót Atdec TH-3070-UF flat panel wall mount (2 oldal) a Lapos panel támogatás kategóriában. Ezt az útmutatót 2 ember találta hasznosnak és 2 felhasználó értékelte átlagosan 4.5 csillagra

Letöltés PDF
Oldal 1/2
Bits Bag
Component Checklist
Installation Instructions
FLAT SCREEN WALL MOUNT | FIXEDTH-3070-UF
Display Bracket (x2)
Wall Plate
Important Notes
TOOLS REQUIRED:
 Power Drill
 12mm (1/2”), 10mm (3/8”) or 7mm (1/4”) Drill Bit
 Phillips Head Screw Driver
 Spirit Level
 17mm (11
/16”) Socket Wrench or Shifter
Supports a maximum load of 91kgs (200lbs).
Suits displays with mounting hole patterns from 180mm to 810mm wide (7”-313/4”) by 125mm to 500mm
high (5”-191/2”).
The manufacturer does not accept responsibility for incorrect installation.
Security Bracket
Mounting Screws
M8x15mm / M8x35mm / M8x45mm (x4 each)
M6x15mm / M6x35mm / M6x45mm (x4 each)
M5x15mm / M5x35mm / M5x45mm (x4 each)
M4x15mm / M4x35mm / M4x45mm (x4 each)
Cross Recessed Screws
Coach
Screw (x4)
Masonry Wall
Plug (x4)
Washer (x4)
Multi
Washer (x4)
Dry Wall
Anchor (x6)
™
Mounting the Wall Plate
A
Masonry Wall
Washer
Masonry
Wall Plug
Wall Plate
12mm (1/2”)
Hole
Coach Screw
Dry Wall Timber Stud Wall
TIP: Use a spirit level to
ensure the wall plate is
horizontal
TIP: Use a spirit level to
ensure the wall plate is
horizontal
TIP: Use a spirit level to
ensure the wall plate is
horizontal
Wall Plate
Coach Screw Washer
Timber
Stud10mm (3/8”)
Hole
Wall Plate
Dry Wall
Anchor
Dry Wall
Anchor Screw
Dry Wall
Anchor Washer Use a stud finder to precisely
locate the timber stud and
ensure that the mounting holes
are located in the centre of
the stud.
It is recommended when
mounting directly into masonry
wall, that the mounting holes
are positioned as far apart as
possible.
7mm (1/4”)
Hole
Note: Ensure the Wall Plate
is mounted with the folded
tabs pointing upwards.
Note: Ensure the Wall Plate
is mounted with the folded
tabs pointing upwards.
Note: Ensure the Wall Plate
is mounted with the folded
tabs pointing upwards.
The dry wall anchors provided in
the bit bag have been tested for
this wall mount application and will
each hold in excess of 30kg per
anchor.
Before using the expanding
anchors, please ensure that you:
· Check the plaster board wall (dry
wall) is in good condition with no
cracks, peeling paper or signs of
water damage etc.
· Take care installing the anchors,
that they are not over tightened
or driven into the wall during
installation.
· Minimum thickness of drywall
should be no less than 12mm (1/2”)
· Recommend to use all 6 anchors
even with light monitor applications.
· Only use the anchors supplied
in the kit.
· Make sure the 10mm (3/8”) pre-
drilled hole is as recommended and
no smaller or larger.
· The anchors during expansion
should not interfere with studs or
noggins (cross strengtheners).
13mm Spacer
Bush (x4)
20mm Spacer
Bush (x4)
Recessed Mounting Holes
B
C
Multi
Washer
M6 & M8
Screw Hole
M4 & M5
Screw Hole
Mounting
screw When attaching the Brackets ensure
that both are vertically aligned.
Ensure that the tightest fitting hole
in the multi washer is used when
attaching the mounting screw.
E
For additional security, it is suggested that a Padlock is
attached through the Security Bracket and the Wall Plate
on either side as shown. The Padlock (not supplied) should
have a shackle diameter no larger than 5mm (3/16”).
No portion of this document or any artwork contained herein should be reproduced in any way without the express written consent of Atdec Pty Ltd.
Due to continuing product development, the manufacture reserves the right to alter specifications without notice. Published: 19.02.09 ©
E.2.
E.1.
(not supplied)
With the Brackets attached
to the display, lift the display
and hook the brackets onto
the Wall Plate as shown.
There are three height
positions to choose from in
50mm (2”) increments.
Spacer
Bush
If the mounting holes are recessed
into the back of the display, use
the appropriate Spacer Bushes
provided to pack the recessed hole.
Please note the 13mm Spacer
Bushes can only be used with M4,
M5, and M6 Mounting screws.
Ensure the brackets are securely
fixed to the display.

Termékspecifikációk

Márka: Atdec
Kategória: Lapos panel támogatás
Modell: TH-3070-UF flat panel wall mount

Szüksége van segítségre?

Ha segítségre van szüksége Atdec TH-3070-UF flat panel wall mount, tegyen fel kérdést alább, és más felhasználók válaszolnak Önnek


Útmutatók Lapos panel támogatás Atdec

Atdec

Atdec AWM-W-S Útmutató

7 December 2024
Atdec

Atdec AD-WF-8060 Útmutató

7 December 2024
Atdec

Atdec AD-WT-8060 Útmutató

7 December 2024
Atdec

Atdec TH-1030-VFM Útmutató

19 Augusztus 2024
Atdec

Atdec TH-30-50-RW Útmutató

19 Augusztus 2024
Atdec

Atdec TH-3070-UF flat panel wall mount Útmutató

19 Augusztus 2024
Atdec

Atdec TH-3070-CTW Útmutató

18 Augusztus 2024
Atdec

Atdec L-PB Útmutató

18 Augusztus 2024
Atdec

Atdec VF-AT-W/TAA Útmutató

18 Augusztus 2024
Atdec

Atdec SD-DP-750 Útmutató

18 Augusztus 2024

Útmutatók Lapos panel támogatás

Legújabb útmutatók Lapos panel támogatás

Kanto

Kanto FMX2 Útmutató

9 December 2024
Proaim

Proaim CT-SDCF-PRO Útmutató

7 December 2024
Proaim

Proaim CT-SDCF-OG Útmutató

7 December 2024
Proaim

Proaim CT-SDCF-CV4 Útmutató

7 December 2024
NEC

NEC PDVWXUN 55 P Útmutató

15 Október 2024
Insignia

Insignia NS-STV3N1705 Útmutató

15 Október 2024
Abus

Abus BW8060 Útmutató

4 Október 2024
One For All

One For All DM 4110 Útmutató

2 Október 2024
NEC

NEC PD01CMB Útmutató

2 Október 2024
One For All

One For All DM 7220 Útmutató

1 Október 2024