Használati útmutató Atdec AD-WT-8060

Atdec Lapos panel támogatás AD-WT-8060

Olvassa el alább 📖 a magyar nyelvű használati útmutatót Atdec AD-WT-8060 (4 oldal) a Lapos panel támogatás kategóriában. Ezt az útmutatót 3 ember találta hasznosnak és 2 felhasználó értékelte átlagosan 4.5 csillagra

Letöltés PDF
Oldal 1/4
AD-WT-8060 Page 1 of 4
Installation Guide
AD-WT-8060
Tilt Wall Mount 8060
IMPORTANT INFORMATION
! Please ensure this product is installed as per these installation instructions.
! The manufacturer accepts no responsibility for incorrect installation.
! Failure to mount this product correctly may cause serious injury/death during or following installation.
! This product is not suitable for outdoor use.
! Do not use this product for mobile applications.
! Wall Plate only achieves maximum weight rating when appropriately fastened to a wall of adequate structural capacity.
! Professional installer to ensure adequate structural capacity of wall (including appropriate safety factor) to support total
weight of all equipment being mounted.
! Drilling into electrical wires can cause death - use appropriate equipment and caution when drilling holes in walls to avoid
electrical cables, water pipes and gas pipes. Do not drill into structures unless you have established it’s safe to do so.
M-C
M6x30
Screw
(x4)
M-B
M6x14
Screw
(x4)
M-D
M8x30
Screw
(x4)
M-A
M5x14
Screw
(x4)
M-F
Multi
Washer
(x4)
M-G
Short
Spacer
(x8)
M-E
M8x50
Screw
(x4)
B
Display Bracket (left)
C
Display Bracket (right)
A
Wall Plate
D
Security Bar
M-H
Long
Spacer
(x8)
E
Hex Key
REQUIRED TOOLS
• Phillips head screwdriver
• Power drill
• Suitable drill bit
• Driver bit for selected
wall fasteners
• Stud nder
• Spirit level
• Socket wrench set
COMPONENT CHECKLIST
0 - 80kg
(0 - 176lb)
WEIGHT RANGE
NOTE:
! Wall Plate Mounting Fasteners are NOT supplied with Wall Mounts.
Professional installer to ensure correct Mounting Fastener type, location &
quantity to suit structure where Wall Mount is installed.
! ALWAYS use a washer between the chosen fastener and the wall plate.
! Mounting fasteners to be used as per manufacturers instructions, including
minimum engagement to achieve necessary performance.
AD-WT-8060 Page 2 of 4
12 3
3. Hook and Secure the Display onto the Wall Plate
NOTE:
Ensure level adjustment
screws are retracted prior
to mounting the display.
3.1. Angle the display and hook the Display
Brackets over the top of the Wall Plate.
This should be completed by two people.
NOTE:
• Choice and supply of appropriate wall plate fasteners is the
responsibility of the installer.
• Consult a preferred fastener supplier or a structural engineer
to select fasteners which are most appropriate for the weight
of the display and wall construction method.
• Wall plate be level. Verify using a quality spirit level tool.must
• On a Stud Wall or Drywall use a good quality Stud Finder to
position mounting fasteners in the centre of studs.
• On a Masonry Wall avoid positioning Wall Plate mounting
fasteners in a mortar join.
B
C
M-H (OPTIONAL)
SPACER HEIGHT (mm)
M-G (OPTIONAL)
M-A
M-B
M-C
M-D
M-E
(M5x14)
(M6x14)
(M6x30)
(M8x30)
(M8x50)
M-F
403530252015105
2. Attach the Display Brackets to the Display
3.2. DSlide Security Bar through the slots at the bottom of each
Display Bracket, ensuring the Security Bar sits to the rear of
the Wall Plate and the display cannot be lifted up and off the
Wall Plate.
3.3. (OPTIONAL) To prevent theft of the display, add a padlock to
the end of . Security Bar D
1. Mount the Wall Plate to the Wall
Slot Dimension
Ø9 x 55mm
*Fasteners shown are for example only
NOTE:
• Always use multi-washers M-F.
• Ensure the display brackets are
not loose and screws are not
forced too deep into the display.
• If spacers are needed, use the
shortest possible combination
between the display bracket and
the display.
AD-WT-8060 Page 3 of 4
Remove the black plastic caps
from Display Brackets and B C.
Tilt the display to the desired
viewing angle and tighten the
nuts using a suitable socket
wrench tool to lock the angle
in place.
NOTE:
Support display whilst adjusting tilt.
NOTE:
Support display whilst turning the level adjustment screws.
Level Adjustment Display Tilt
ADJUSTMENTS
If needed, carefully turn the
screws at the top of each
display bracket clockwise using
Hex Key to level the display. E

Termékspecifikációk

Márka: Atdec
Kategória: Lapos panel támogatás
Modell: AD-WT-8060

Szüksége van segítségre?

Ha segítségre van szüksége Atdec AD-WT-8060, tegyen fel kérdést alább, és más felhasználók válaszolnak Önnek


Útmutatók Lapos panel támogatás Atdec

Atdec

Atdec AWM-W-S Útmutató

7 December 2024
Atdec

Atdec AD-WF-8060 Útmutató

7 December 2024
Atdec

Atdec AD-WT-8060 Útmutató

7 December 2024
Atdec

Atdec TH-1030-VFM Útmutató

19 Augusztus 2024
Atdec

Atdec TH-30-50-RW Útmutató

19 Augusztus 2024
Atdec

Atdec TH-3070-UF flat panel wall mount Útmutató

19 Augusztus 2024
Atdec

Atdec TH-3070-CTW Útmutató

18 Augusztus 2024
Atdec

Atdec L-PB Útmutató

18 Augusztus 2024
Atdec

Atdec VF-AT-W/TAA Útmutató

18 Augusztus 2024
Atdec

Atdec SD-DP-750 Útmutató

18 Augusztus 2024

Útmutatók Lapos panel támogatás

Legújabb útmutatók Lapos panel támogatás

Kanto

Kanto FMX2 Útmutató

9 December 2024
Proaim

Proaim CT-SDCF-PRO Útmutató

7 December 2024
Proaim

Proaim CT-SDCF-OG Útmutató

7 December 2024
Proaim

Proaim CT-SDCF-CV4 Útmutató

7 December 2024
NEC

NEC PDVWXUN 55 P Útmutató

15 Október 2024
Insignia

Insignia NS-STV3N1705 Útmutató

15 Október 2024
Abus

Abus BW8060 Útmutató

4 Október 2024
One For All

One For All DM 4110 Útmutató

2 Október 2024
NEC

NEC PD01CMB Útmutató

2 Október 2024
One For All

One For All DM 7220 Útmutató

1 Október 2024