Használati útmutató Atdec TH-30-50-RW

Atdec Lapos panel támogatás TH-30-50-RW

Olvassa el alább 📖 a magyar nyelvű használati útmutatót Atdec TH-30-50-RW (2 oldal) a Lapos panel támogatás kategóriában. Ezt az útmutatót 3 ember találta hasznosnak és 2 felhasználó értékelte átlagosan 4.5 csillagra

Letöltés PDF
Oldal 1/2
Component Checklist
Bits Box Mounting
Screws
Installation Instructions
TELEHOOK
30”-50” UNIVERSAL ROTATING WALL MOUNT
Attaching the Display to the Wall Plate
C
Mounting the Wall Plate
A
Masonry Wall Timber Stud Wall
Adjusting the Pivot Head to suit the weight of the
Display
The Pivot head is factory set to hold
approximately 35kgs (77lbs). If the display is not
holding its position when placed on the wall it
may be necessary to remove the display from
the wall and tighten the M12 Hex Nut on the
back of the Pivot Head using a 17mm (
11/16”)
socket wrench or shifter. To achieve a one-touch
effortless adjustment setting it is advised that the
nut be tightened at half turns and re-tested, until
the desired friction is achieved. Alternatively the
M12 Hex Nut can be over tightened in order to
lock the display in position.
Bracket (x2)
Pivot Head
Extension Plate
Wall Plate
Bracket Plate (x2)
Coach
Screw (x4)
Masonry Wall
Plug (x4)
Large
Washer (x4)
Multi
Washer (x4)
Spacer
Bush (x4)
M6x16mm Socket
Drive Screw (x12)
M8x20mm
Phillips Head
Screw (x4)
M6x16mm
Phillips Head
Screw (x6)
M5x16mm
Phillips Head
Screw (x6)
Allen Key
Small
Washer (x4)
Large Washer
Masonry
Wall Plug
Wall Plate
12mm (1/2
”)
Hole
TIP: Use a spirit
level to ensure the
wall plate is
horizontal
Note: Ensure the Wall Plate
is mounted with the narrow
end of the Mounting Slot
at the bottom.
Coach Screw
Note: Ensure the Wall Plate is
mounted with the narrow end of the
Mounting Slot at the bottom.
Large
Washer
Coach Screw
8mm (5/16 ”)
Hole
Timb er
Stud
With the mount attached to the display, lift the
display and slide the Back Plate into the Mounting
slots to ensure a secure connection.
Tighten
M12 Hex Nut
Security Option
D
For additional security,
it is suggested that a
Padlock be attached to
the Back plate as shown.
The Padlock (not supplied)
should have a shackle
diameter no larger than
4mm (3/16”).
Padlock
Note: This procedure will require two persons
Back Plate
Mounting
Slots
Mounting Slot
Note: For demonstration purposes, the display
has been omitted from the image below.
Back plate
Shackle 4mm (3/16”)
diameter or less
Due to continuing product development, the manufacturer reserves the right to alter specifications without notice. Published: 18.04.07 ©
Important Notes
TOOLS REQUIRED:
Power Drill
12mm or 8mm Drill Bit
Phillips Head Screw Driver
Spirit Level
17mm (11/16”) Socket Wrench
or Shifter
The Telehook 30-50 Universal Rotating Wall Mount supports flat panel displays from 30” (76cm) to 50” (127cm)
and supports a maximum load of 85kgs (187lbs).
This product is factory set to support 35kgs (77lbs), and will need to be adjusted if the display is heavier or lighter.
The manufacturer does not accept responsibility for incorrect installation.
TIP: Use a spirit
level to ensure the
wall plate is
horizontal
C.1. Attaching the Display to the Wall Plate C.2. Pivot Head Load Capacity Adjustment
M4x16mm
Phillips Head
Screw (x6)
Centre Holes
Note: It is recommended to
mount the Wall Plate by firmly
fixing the four Coach Screws
into two studs. However, if the
weight of the display is less than
50kgs (110lbs), it is possible to
mount the Wall Plate to one stud
by fixing the two Coach Screws
through the two Centre holes.
Note: For demonstration purposes, the wall
has been omitted from the above image.
Configuration 3: 260mm to 660mm (101/4”-26”) x 200mm to 400mm (8”-15 3/4”)
Mounting Hole Patterns
Choosing and Assembling the Correct Mounting Configuration
B
Measure the mounting hole pattern on the back of the display. Select the appropriate configuration (either 1, 2
or 3) that best suits the mounting hole pattern of the display then attach the product to the display as shown.
ii
Mounting Screw
Pivot Head
Back
of Display
Note: The
100mmx200mm
mounting
configuration is
shown. For mounting
displays with
100mmx100mm
mounting hole
patterns, use the
100mmx100mm holes
in the Pivot Head.
Bracket
Plate
Pivot Head
Back
of Display
Bracket
M6 Socket
Drive Screw
Mounting
Screw
Multi Washer
100mm
(4”)
100mm
(4”)
200mm (8”)
260mm
(101/4”)
660mm (26”)
400mm
(153/4”)
200mm
(8”)
Spacer Bush Assembly
If the mounting holes are recessed into the
back of the display, use the supplied Spacer
Bushes to pack the recessed hole and ensure
that the bracket is securely fixed to the display.
Note: If the display has a vertical
mounting distance of 200mm and
requires the use of the M6 Mounting
Screws, it will be necessary to
substitute the MuIti Washers for the
small washers provided.
Pivot Head M6 Socket
Drive Screw
Bracket
Plate Mounting
Screw
Multi Washer
Extension
Plate
Multi Washer
Mounting Screw
Bracket
Recessed Hole
Spacer Bush
Small
Washer
M6 Mounting
Screw
Back
of Display
Configuration 1: VESA Compliant 100mmx100mm (4”x4”) & 100mmx200mm (4”x8”)
Mounting Hole Patterns
Configuration 2: 200mmx200mm to 400mm (8”x8”-15 3/4”) Mounting Hole Patterns
200mm
(8”)
200mm
(8”)
400mm
(153/4”)
Attaching the Bracket to the Display
Note: When assembling the product,
ensure the red Telehook Badges are
positioned towards the bottom of the display
In order to ensure the display is securely attached to the
bracket it is recommended that the bracket be fastened with the
mounting screws aligned along the bottom edge of the slots.
It is also important that you use the supplied Multi Washer and
ensure that the tightest fitting hole in the washer is used for the
specific size screw
M6 Screw
Hole
M8 Screw
Hole
M4 & M5
Screw Hole
Multi Washer
Slot
Telehook
Badge
Note: When assembling the
product, ensure the Telehook
Badges are positioned towards the
bottom of the display
Telehook
Badge
100mm
(4”)
Spacer Bush
Top of
Display
Top of
Display
Top of
Display

Termékspecifikációk

Márka: Atdec
Kategória: Lapos panel támogatás
Modell: TH-30-50-RW

Szüksége van segítségre?

Ha segítségre van szüksége Atdec TH-30-50-RW, tegyen fel kérdést alább, és más felhasználók válaszolnak Önnek


Útmutatók Lapos panel támogatás Atdec

Atdec

Atdec AWM-W-S Útmutató

7 December 2024
Atdec

Atdec AD-WF-8060 Útmutató

7 December 2024
Atdec

Atdec AD-WT-8060 Útmutató

7 December 2024
Atdec

Atdec TH-1030-VFM Útmutató

19 Augusztus 2024
Atdec

Atdec TH-30-50-RW Útmutató

19 Augusztus 2024
Atdec

Atdec TH-3070-UF flat panel wall mount Útmutató

19 Augusztus 2024
Atdec

Atdec TH-3070-CTW Útmutató

18 Augusztus 2024
Atdec

Atdec L-PB Útmutató

18 Augusztus 2024
Atdec

Atdec VF-AT-W/TAA Útmutató

18 Augusztus 2024
Atdec

Atdec SD-DP-750 Útmutató

18 Augusztus 2024

Útmutatók Lapos panel támogatás

Legújabb útmutatók Lapos panel támogatás

Kanto

Kanto FMX2 Útmutató

9 December 2024
Proaim

Proaim CT-SDCF-PRO Útmutató

7 December 2024
Proaim

Proaim CT-SDCF-OG Útmutató

7 December 2024
Proaim

Proaim CT-SDCF-CV4 Útmutató

7 December 2024
NEC

NEC PDVWXUN 55 P Útmutató

15 Október 2024
Insignia

Insignia NS-STV3N1705 Útmutató

15 Október 2024
Abus

Abus BW8060 Útmutató

4 Október 2024
One For All

One For All DM 4110 Útmutató

2 Október 2024
NEC

NEC PD01CMB Útmutató

2 Október 2024
One For All

One For All DM 7220 Útmutató

1 Október 2024