Használati útmutató York Fitness 1001

Olvassa el alább 📖 a magyar nyelvű használati útmutatót York Fitness 1001 (6 oldal) a Fitness berendezések kategóriában. Ezt az útmutatót 3 ember találta hasznosnak és 2 felhasználó értékelte átlagosan 4.5 csillagra

Oldal 1/6
MODEL # 5020 PAGE 1
46/99
A S S E M B L Y I N S T R U C T I O N S
46/99
Home - Gym
1001
1001
PAGE 2
46/99
ASSEMBLY INSTRUCTIONS
MODEL # 5020
22241
33B021
33B022
Home - Gym
1001
PAGE 3
46/99
NOTE: MAXIMUM WEIGHT STACK LIMIT 65KGS. (DO NOT
ADD EXTRA WEIGHTS) MAXIMUM WEIGHT OF USER = 100KG
Before assembly, read each section carefully. If these
instructions are followed exactly you will have no problems
with assembly.
Tools required: Slotted Screwdriver and 2 adjustable
Spanners or 7/16"(11mm) Spanner
1/2"(13mm) Spanner
9/16"(15mm) Spanner
5/8"(16mm) Spanner
Take upholstered piece and place upside down.
Place Pt.2205 on top of upholstery and put three x Pt.2290
(5/8" round tubing) through three large holes in Pt.2205 so that
the holes in the round tubing line up with holes in the
upholstery and Pt. 2205 is in the middle.
Insert six x 1/4"x 1 3/4" slotted screws through holes in
Pt.2290 and screw evenly into holes in the upholstery until
secured. Insert Pt.2235 into Pt.2205. Put one x 3/8" x 2" hex
head bolt through the hole in Pt.2235 and put one x 3/8" nyloc
nut on finger tight.
Assemble pulley wheel
in Pt.2205 as shown in (A)
using:
one x 3" pulley wheel
one x 3/8" washer
one x 5/16" hex nut
one x 3/8" x 13/16" stripper bolt
Pulley wheel should move freely
within bracket.
BAG75
Part No. Description Qty
33A03 1/4" Nyloc Nut 1
33A14 1/4" x 1 3/4" RHSMS 6
33A11 1/4" x 2" RHSMS 1
33A32 5/16" Hex Nut 1
41B400 1/4" Thread Cap 1
33A33 5/16" Nyloc Nut 1
33A51 3/8" Hex Nut 1
33A53 3/8" Nyloc Nut 4
33A48 3/8" x 2" H.H. Bolt 1
33A59 3/8" x 4 1/2" H.H. Bolt 2
33A45 3/8" x 13/16" Stripper Bolt 1
33A46 3/8" x 2" Stripper Bolt 1
33A421 3/8" x 4 1/4" Eye Bolt 1
33B63 3/8" SAE Washer 3
41B402 3/8" Thread Cap 1
41B07 1 1/4" SQ. Int. Cap (Black) 6
41B031 1 1/2" SQ. Int. Cap (Black) 4
41A83 Rubber Bumper 1
41A82 3" Pulley Wheel 1
41B211 Foam Cap 1" (Red) 4
41A81 31.75 IDx107.95mm Handgrip 2
BOX1
Part No. Qty.
Description
32B85 Bag 75 1
32B93 Bag 83 1
27E032 Foam Rollers 4
30E02 Upholstery 1001 1
21E2290 3
21E2202 1
21E2203 2
21E2205 1
21E2235 1
21E2229 1
21E2241 2
Attach finger tight two x Pt.2203 to Pt.2205 using:
two x 3/8" x 4 1/2" hex head bolts
and two x 3/8" nyloc nuts
Install four x 1 1/4" and one x 1 1/2" square internal caps.
Install one x round rubber bumper into Pt.2202 using
one x 1/4" x 2" slotted screw and one x 1/4" nyloc nut.
Take one x 4 1/4" eyebolt and screw on one x 3/8" hex nut until
it can go on no further. Insert eyebolt into back of Pt.2202 and
put on remaining one x 3/8" nyloc nut. Install thread cap.
Install remaining black caps into Pts.2202,2203,and 2205.
SECTION 1
Attach Pt.2202 to Pt.2205 as
in drawing B using:
one x 3/8" x 2" stripper bolt
one x 5/16" nyloc nut
two x 3/8" washers.
Leg curl must move freely
so do not over tighten
Insert two Pts.2241 into Pt.2202, slide on foam rollers and install
four large red foam caps into the tubing.
Now have someone sit on the bench while you tighten all the
remaining bolts. This will level the bench. Bolt in PT.2235 must
be tightened until it will not move inside Pt.2205.
Wet inside hand grips with warm soapy water and install on
Pt.2229.
Now open Box No.2 which contains the following parts:
BAG 27
Part No. Qty.
Description
33A03 1/4" Nyloc Nut 4
33A14 1/4" x 1 3/4" RHSMS 4
41A83 Rubber Bumper 4
BOX 2
Part No. Qty.
Description
32B37 Bag 27 1
32B86 Bag 76 1
32B87 Bag 77 1
32B88 Bag 78 1
21E2225 1
21E2227 1
21E2250 1
Locate Bag No.27 and check contents as listed :
Part No. Description
33A32 5/16" Hex Nut 2
33A45 3/8" x 13/16" Stripper Bolt 2
33B63 3/8" SAE Washer 2
41A82 3" Pulley Wheels 2
BAG 76
Turn Pt.2225 upside down and install the two pulley wheels
as you did before.
Put Bag 77, 78, and Pt. 2227 to one side.
Install Pts. from Bag 27 into
Pt.2225 as shown in C.
Locate Bag 76 and check contents as listed:
Qty.

Termékspecifikációk

Márka: York Fitness
Kategória: Fitness berendezések
Modell: 1001

Szüksége van segítségre?

Ha segítségre van szüksége York Fitness 1001, tegyen fel kérdést alább, és más felhasználók válaszolnak Önnek




Útmutatók Fitness berendezések York Fitness

Útmutatók Fitness berendezések

Legújabb útmutatók Fitness berendezések