Használati útmutató Toshiba RAS-13SKV

Toshiba légkondicionáló RAS-13SKV

Olvassa el alább 📖 a magyar nyelvű használati útmutatót Toshiba RAS-13SKV (8 oldal) a légkondicionáló kategóriában. Ezt az útmutatót 5 ember találta hasznosnak és 2 felhasználó értékelte átlagosan 4.5 csillagra

Letöltés PDF

Oldal 1/8

E N G L I S H

O W N E R’ S M A N U A L

AIR CONDITIONER (SPLIT TYPE)

For general public use

Indoor unit

RAS-10, 13, 16 SKV Series

Outdoor unit

RAS-10, 13, 16 SAV Series

1110250102-(1).indd 1

1110250102-(1).indd 11110250102-(1).indd 1

1110250102-(1).indd 1

1/4/07 4:48:00 PM

1/4/07 4:48:00 PM1/4/07 4:48:00 PM1/4/07 4:48:00 PM

Press

FIX

: Move the louver in the

desired vertical direction.

Press

SWING

: Swing the air

automatically and press again to stop.

For horizontal direction, adjust

manually.

DANGER

•

Do not install, repair, open or remove the cover. It may expose you

to dangerous voltages. Ask the dealer or the specialist to do this.

•

Turning off the power supply will not prevent potential electric

shock.

•

The appliance shall be installed in accordance with national wiring

regulation.

•

Means for disconnection from the supply having a contact

separation of at least 3 mm in all poles must be incorporated in the

ﬁ xed wiring.

WARNING

•

Do not expose your body directly to cool air for a long time.

•

Do not insert your ﬁ nger or any article into the air inlet/outlet.

•

When an abnormality (burning smell, etc.) occurs, stop the air

conditioner and disconnect the power supply or turn off the

breaker.

CAUTION

•

Do not wash the unit with water. It may cause an electric shock.

•

Do not use this air conditioner for other purposes such as

preserving food, breeding animal, etc.

•

Do not step or put anything on the indoor/outdoor unit. It may

cause an injury or damage the unit.

•

Do not touch aluminium ﬁ n because it may cause an injury.

•

Before cleaning the unit, turn off the main switch or the circuit

breaker.

•

When the unit won’t be used for a long time, turn off the main

switch or the circuit breaker.

•

It is recommended that maintenance be performed by a specialist

when the unit has been operated for a long time.

PRECAUTIONS FOR SAFETY

INDOOR UNIT DISPLAY

1 Hi POWER (Green)

2 FILTER (Orange)

3 PURE (Blue) (10, 13, 16SKVR-A series)

3 PRE DEF (DE-FROST) (Orange)

(13, 16SKV-A series)

4 TIMER (Yellow)

5 OPERATION (Green)

6 RESET button

Hi POWER FILTER PURE TIMER OPERATION

RESET

1 2 3

4 5

PREPARATION BEFORE USE

Preparing Filters

1. Open the air inlet grille and remove the air ﬁ lters.

2. Attach the ﬁ lters. (see detail in the accessory sheet).

Loading Batteries

1. Remove the battery cover.

2. Insert 2 new batteries (AAA type)

following the (+) and (–) positions.

Clock Setup

1. Push CLOCK ● by tip of the pencil.

2. Press ON or OFF : adjust the time.

3. Press SET : Set the time.

Remote Control Reset

1. Remove the battery.

2. Press .

3. Insert the battery.

AIRFLOW DIRECTION

• Do not move the louver manually by others.

• The louver may automation positioning by come operation mode.

Note:

REMOTE CONTROL

PRESET

ONE-TOUCH

QUIET

SWING

TIMER

FILTER

CHK

CLOCK

OFF

CLR

SLEEP

SET

FIX Hi-POWER ECO

PURE

COMFORT

SLEEP

MODE

TEMP

FAN

(

)

1 Infrared signal emitter

2 Start/Stop button

3 Mode select button (MODE)

4 Temperature button (TEMP)

5 Fan speed button (FAN)

6 Swing louver button (SWING)

7 Set louver button (FIX)

8 On timer button (ON)

9 Off timer button (OFF)

! Sleep timer button (SLEEP)

" Setup button (SET)

# Clear button (CLR)

$ Memory and Preset button (PRESET)

% One Touch button (ONE-TOUCH)

& High power button (Hi-POWER)

( Economy button (ECO)

) Quiet button (QUIET)

~ Comfort sleep button (COMFORT SLEEP)

+ Plasma Air Puriﬁ er button (PURE)

(RAS-10, 13, 16SKVR-A Only)

, Filter reset button (FILTER)

- Clock Reset button (CLOCK)

. Check button (CHK)

ONE-TOUCH

Press the “ONE-TOUCH” button for fully automated operation that is customised

to the typical consumer preferences in your region of the world. The customised

settings control temperature air ﬂ ow strength, air ﬂ ow direction and other settings

to provide you alternate contact with “ONE-TOUCH” of the button. If you prefer

other settings you can select from the many other operating functions of your

Toshiba unit.

Press

ONE-TOUCH

: Start the operation.

AUTOMATIC OPERATION

To automatically select cooling, heating, or fan only operation

1. Press

MODE

: Select A.

2. Press

TEMP

: Set the desired temperature.

COOLING / HEATING / FAN ONLY OPERATION

1. Press

MODE

: Select Cool , Heat , or Fan only .

2. Press

TEMP

: Set the desired temperature.

Cooling: Min. 17oC, Heating: Max. 30oC, Fan Only: No temperature indication

3. Press

FAN

: Select AUTO, LOW , LOW+ , MED , MED+ , or

HIGH .

DRY OPERATION

For dehumidiﬁ cation, a moderate cooling performance is controlled

automatically.

1. Press

MODE

: Select Dry .

2. Press

TEMP

: Set the desired temperature.

AIR PURIFYING OPERATION

(RAS-10, 13, 16SKVR-A Only)

During air conditioner operation

Press

PURE

to start and stop plasma air puriﬁ er and air ionizer operation.

The plasma air puriﬁ er and air ionizer can be activated or deactivated during air

conditioner is stopped and the air ionizer starts in conjunction with plasma air

puriﬁ er operation.

Note: The FILTER indicator (orange) turns on after PURE operation is performed

for about 1000 hours.

Hi-POWER OPERATION

To automatically control room temperature and airﬂ ow for faster cooling or heating

operation (except in DRY and FAN ONLY mode)

Press

Hi-POWER

: Start and stop the operation.

ECO OPERATION

To automatically control room to save energy (except in DRY and FAN ONLY

mode)

Press

ECO

: Start and stop the operation.

Note: Cooling operation; the set temperature will increase automatically 1 degree/

hour for 2 hours (maximum 2 degrees increase). For heating operation the

set temperature will decrease.

CLEANING

RESET TIMER OPERATION

3 2 1

1 OPERATION (Green)

2 TIMER/CLEANING (Yellow)

3 RESET button

Models: RAS-10, 13, 16SKVR-A, RAS-13, 16SKV-A

Models: RAS-10SKV-A

1110250102-(1).indd 2

1110250102-(1).indd 21110250102-(1).indd 2

1110250102-(1).indd 2

1/4/07 4:48:03 PM

1/4/07 4:48:03 PM1/4/07 4:48:03 PM1/4/07 4:48:03 PM

TEMPORARY OPERATION

In case of the misplaced or discharged remote control

• Pressing the RESET button, the unit can start or stop

without using the remote control.

• Operation mode is set on AUTOMATIC

operation, preset temperature is 24°C

and fan operation is automatic speed.

TIMER OPERATION

Everyday timer allows the user to set both the ON & OFF timers and will be activated on a daily basis.

Setting the ON Timer Setting the OFF Timer

Press

: Set the desired ON timer.

Press

OFF

: Set the desired OFF timer.

2Press SET : Set the timer. Press SET : Set the timer.

3Press

CLR

: Cancel the timer. Press

CLR

: Cancel the timer.

• Keep the remote control in accessible transmission to the indoor unit;

otherwise, the time lag of up to 15 minutes will occur.

• The setting will be saved for the next same operation.

Note:

Setting Everyday Timer

1Press

: Set the ON timer. 3Press SET .

2Press

OFF

: Set the OFF timer. 4Press SET button during the ( or )

mark ﬂ ashing.

• During the every day timer is activating, both arrows ( , ) are indicated.

PRESET OPERATION

Set your preferred operation for future use. The setting will be memorized by the

unit for future operation (except airﬂ ow direction).

1. Select your preferred operation.

2. Press and hold

PRESET

for 3 seconds to memorize the setting. The P mark

displays.

3. Press

PRESET

: Operate the preset operation.

AUTO RESTART OPERATION

To automatically restart the conditioner after the power failure (Power of the unit

must be on.)

Setting

1. Press and hold the RESET button on the indoor unit for 3 seconds to set the

operation. (3 beep sound and OPERATION lamp blink 5 time/sec for 5 seconds)

• Do not operate ON timer and OFF timer.

2. Press and hold the RESET button on the indoor unit for 3 seconds to cancel the

operation. (3 beep sound but OPERATION lamp does not blink)

To operate at super low fan speed for quiet operation (except in DRY mode)

Press

QUIET

: Start and stop the operation.

Note: Under certain conditions, QUIET operation may not provide adequate

cooling or heating due to low sound features.

To save energy while sleeping, automatically control air ﬂ ow and automatically

turn OFF.

Press

COMFORT

SLEEP

: Select 1, 3, 5 or 9 hrs for OFF timer operation.

Note: The cooling operation, the set temperature will increase automatically

1 degree/hour for 2 hours (maximum 2 degrees increase). For heating

operation, the set temperature will decrease.

Cleaning the plasma air puriﬁ er unit (About 1000 hours performed)

(RAS-10, 13, 16SKVR-A Only)

1. Turn off air conditioner using remote control and power supply.

2. Take out the air inlet grille (See detail in installation manual).

3. Take out the plasma air puriﬁ er by grasp the handle, and the pull it out.

4. Soak in hot water at 40oC to 50oC for about 10 to 15 minutes and rub up,

down, left, right and rub surface gently with a sponge.

5. Allow to dry thoroughly in the shade.

6. Attach the plasma air puriﬁ er by grasp the

handle and insert into the right and left

guide rails.

7. Press both ends of the plasma air puriﬁ er

until the protrusions on both sides of the

plasma air puriﬁ er are completely inserted.

8. Attach the air ﬁ lter, and then close the air

inlet grille.

QUIET OPERATION

COMFORT SLEEP OPERATION

SELF CLEANING OPERATION (COOL AND DRY OPERATION ONLY)

OPERATION AND PERFORMANCE

1. Three-minute protection feature: To prevent the unit from being activated for 3

minutes when suddenly restarted or switched to ON.

2. Preheating operation: Warm up the unit for 5 minutes before the heating

operation starts.

3. Warm air control: When the room temperature reaches the set temperature,

the fan speed is automatically reduced and the outdoor unit will stop.

4. Automatic defrosting: Fans will stop during defrost operation.

5. Heating capacity: Heat is absorbed from outdoors and released into the room.

When the outdoor temperature is too low, use another recommended heating

apparatus in combination with the air conditioner.

6. Consideration for accumulated snow: Select the position for outdoor unit

where it will not be subjected to snow drifts, accumulation of leaves or other

seasonal debris.

7. Some minor cracking sound may occur when unit operating. This is normal

because the cracking sound may be caused by expansion/contraction of

plastic.

Item 2 to 6 for Heating model Note:

Air conditioner operating conditions

Temp.

Operation

Outdoor Temperature Room

Temperature

10, 13, 16SKVR-A

13, 16SKV-A 10SKV-A

Heating –15°C ~ 24°C –10°C ~ 24°C Less than 28°C

Cooling –10°C ~ 46°C 15°C ~ 43°C 21°C ~ 32°C

Dry –10°C ~ 46°C 15°C ~ 43°C 17°C ~ 32°C

The unit does not operate.

Cooling or Heating is abnormally low.

• The power main switch is turned off.

• The circuit breaker is activated to

cut off the power supply.

• Stoppage of electric current

• ON timer is set.

• The ﬁ lters are blocked with dust.

• The temperature has been set

improperly.

• The windows or doors are opened.

• The air inlet or outlet of the outdoor

unit is blocked.

• The fan speed is too low.

• The operation mode is FAN or DRY.

TROUBLESHOOTING (CHECK POINT)

REMOTE CONTROL A-B SELECTION

To separate using of remote control for each indoor unit in case of 2 air conditioner

are installed nearly.

Remote Control B Setup.

1. Press RESET button on the indoor unit to turn the air conditioner ON.

2. Point the remote control at the indoor unit.

3. Push and hold CHK ●

button on the Remote Control by the tip of the pencil. “00” will

be shown on the display.

4. Press

MODE

during pushing CHK ●. “B” will show on the display and “00”

will disappear and the air conditioner will turn OFF. The Remote Control B is

memorized.

Note: 1. Repeat above step to reset Remote Control to be A.

2. Remote Control A has not “A” display.

3. Default setting of Remote Control from factory is A.

To start the sleep timer (OFF timer) operation

Press

SLEEP

: Select 1, 3, 5 or 9 hrs for OFF timer operation.

SLEEP TIMER OPERATION

Firstly, turn off the circuit breaker.

Filter Reset (Some models only)

FILTER lamp lights on; the ﬁ lter must be cleaned.

To turn off the lamp, push the RESET button on the indoor unit or the FILTER

button on the remote control.

Indoor Unit and Remote Control

• Clean the indoor unit and the remote control with a wet cloth when needed.

• No benzine, thinner, polishing powder or chemically-treated duster.

Cleaning the air ionizer (Once every six months) (RAS-10, 13, 16SKVR-A Only)

1. Turn off air conditioner using remote control and power supply.

2. Fully open the vertical air ﬂ ow louvers by hand.

3. Use a toothbrush to rub the ends of metal pin three or four times.

Note: Do not use cotton swabs or other objects with ﬂ uff.

MAINTENANCE

To protect bad smell caused by the humidity in the indoor unit.

1. If the button is pressed once during “Cool” or “Dry” mode, the fan will continue

to run for other 20 minutes, then it will turn off automatically. This will reduce the

moisture in the indoor unit.

2. To stop the unit immediately, press the 3 times within 30 seconds.

Note:

• SELF CLEANING operation is default setting from factory.

• To cancel this function, press and hold the reset button on the indoor unit for 20

seconds.

The SELF CLEANING operation will be cancelled. (5 beep sound but OPERATION

lamp does not blink)

• Do the same to set this function again. (5 beep sound and OPERATION lamp

blink 5 time/sec for 5 seconds)

• AUTO RESTART operation will be cancelled by setting or cancellation of SELF

CLEANING operation. Set it again if necessary.

1110250102-(1).indd 3

1110250102-(1).indd 31110250102-(1).indd 3

1110250102-(1).indd 3

1/4/07 4:48:08 PM

1/4/07 4:48:08 PM1/4/07 4:48:08 PM1/4/07 4:48:08 PM

Termékspecifikációk

Márka:	Toshiba
Kategória:	légkondicionáló
Modell:	RAS-13SKV

Szüksége van segítségre?

Ha segítségre van szüksége Toshiba RAS-13SKV, tegyen fel kérdést alább, és más felhasználók válaszolnak Önnek

Az Ön neve*

Az Ön e-mail címe*

Írja ide kérdését

Útmutatók légkondicionáló Toshiba

Toshiba RAS-B10SKVP-E Útmutató

16 Január 2025

Toshiba RAS-13SKV Útmutató

16 Január 2025

Toshiba RAS-15LKV-UL Útmutató

16 Január 2025

Toshiba MCY-MAP0501HT Útmutató

13 Október 2024

Toshiba RAS-25G2AVP-ND Útmutató

4 Október 2024

Toshiba MCY-MAP0401HT Útmutató

23 Szeptember 2024

Toshiba RAS-12SKVP-ND Útmutató

15 Szeptember 2024

Toshiba RAS-34E2KVG-A Útmutató

28 Augusztus 2024

Toshiba RAS-07E2KV2G-A Útmutató

28 Augusztus 2024

Toshiba RAS-22E2KV2G-A Útmutató

28 Augusztus 2024

Útmutatók légkondicionáló

Legújabb útmutatók légkondicionáló

ARGO Crono Útmutató

16 Január 2025

Honeywell CO25MM Útmutató

16 Január 2025

Gree CE52-24/F(C) Útmutató

16 Január 2025

Daikin RXM50A5V1B8 Útmutató

16 Január 2025

Daikin RXP50N5V1B8 Útmutató

16 Január 2025

Midea MSEPB-25CRFN8 Útmutató

16 Január 2025

Whirlpool AMD 052 Útmutató

15 Január 2025

Maxicool SGL 18COC Útmutató

15 Január 2025

Honeywell MN09CESWW Útmutató

15 Január 2025

Frigidaire FAA082P7A Útmutató

15 Január 2025