Használati útmutató Emko ESM-1520-N

Emko hőmérséklet szabályozó ESM-1520-N

Olvassa el alább 📖 a magyar nyelvű használati útmutatót Emko ESM-1520-N (3 oldal) a hőmérséklet szabályozó kategóriában. Ezt az útmutatót 7 ember találta hasznosnak és 2 felhasználó értékelte átlagosan 4.5 csillagra

Letöltés PDF

Oldal 1/3

ESM-1520-N

ESM-1520N DIN Rail Mounting Temperature Controller

- 3 Digi ts display

J type thermocouple Input or,

K type t

ire PT 1 00 In put or,

- Selectable heating or cooling function

- NTC Input or,

PTC Input or,

hermocouple I nput or,

ire PT 1 000 Input (It must be determined in order)

- PID or ON/OFF temperature control

- Selection of ope ration with hysteresis

- Adjustable temperature offset

- Set value low limit and set value high limit boundaries

- SSR driver output

- Operation selection of compressor operates continuousl y, stops

or operates periodic ally in c ase of probe defect

- Compressor protection d elays

- Alarm parameters

- Password protection for programming mode

- Having CE ma rk a ccording to European Norms

Instruction Manual. ENG ESM-1520N 01 V00 08/23

ESM-1520N DIN Rail Mounting Type

Digital Temperature Controller

1.4 Warranty

A visual inspection of this product for possible damage occured during shipment is

recommended before installation. It is your responsibility to ensure that qualified

mechanical and electrical technicians install this product.

If there is danger of serious accident resulting from a failure or defect in this unit, power

off the system and the electrical connection of the device from the system.

The unit is normally supplied without a power supply switch or a fuse. Use power switch

and fuse as required.

Be sure to use the rated power supply voltage to protect the unit against damage and to

prevent failure.

Keep the power off until all of the wiring is completed so that electric shock and trouble

with the unit can be prevented.

Never attempt to disassemble, modify or repair this unit. Tampering with the unit may

results in malfunction, electric shock or fire.

Do not use the unit in combustible or explosive gaseous atmospheres.

During the equipment is putted in hole on the metal panel while mechanical installation

some metal burrs can cause injury on hands, you must be careful.

Montage of the product on a system must be done with it’s fixing clamps. Do not do the

montage of the device with inappropriate fixing clamp. Be sure that device will not fall

while doing the montage.

It is your responsibility if this equipment is used in a manner not specified in this

instruction manual.

separate

1.3 Installation

7. Specifications

Device Type

Housing&Mounting

Protection Against

Mechanical Impacts

Protection Class

Weight

Environmental Ratings

Storage / O perating Temperature

Storage / O perating Humidity

Installation

Overvoltage Category

Pollution De gree

Operating Con ditions

Supply Voltage a nd Power

Temperature Sensor Inputs

NTC Input Type

PTC Input Type

Thermoc ouple Input Types

Thermoresistance Inpu t Type

Accuracy

Cold Junction Compensation

Sensor Break Protection

Sampling Cycle

Control Form

Relay Output

SSR Output

Display

Leds

Appr ovals : , ,

: Temperature Con tro ller

: 1 Joule (IK06)

: IP20.

: Approximate ly 0.14 Kg.

: Standard, i ndoor at an altitude of less than 2000 meters

with n one conden sing humidity.

: -30 C to +80 C / -20 C to +70 C

: 9 0 % max. (None condensing)

: DIN Rail Mounting

: II.

: II, office or workplace, none conductive pollution

: Continuous

: 1 00- 4 V (-%15, +%10) 50/60 Hz - 2. 5

V (± 15%) 50/60 Hz - 2.5

24 V (± 15%) 50/60 Hz - 2.5

V (- 15%, + 10%) 50/60 Hz - 2.5

V - 2.5 W

: NTC, P TC, TC, RTD

: NTC (10 k @.25 °C )

: PTC (1000 @.25 °C )

: J, K (IEC584.1)(ITS90)

: PT-100, PT- 1000 (IEC751)(ITS90)

: ±1% of full scale for thermoco uple and ther moresi stance

: Automatically ± 0.1°C/1°C.

: Upscale

: 3 samples pe r secon d

: ON / OFF

: Resistive Load 5 A@250 V

(Electrical Life : 100.000 operation (Full Load)

: Maximum 28 mA, Maximum 15 V

: 9 mm Red 3 digits LED Display

90mm x 35mm x 61.2mm plastic housing for Rail Mounting.

o o o o

2 0 VA

230 VA

115 VA

24 VA

10...30

SV (Orange),P(Red),Control OUT (Red),Alarm OUT (Red)

1.Preface

1.2 General Specifications

ESM-1520N series temperature controllers are designed for measuring and controlling

temperature. They can be used in many applications with their On / Off control form, heating and

cooling control form and easy-use properties. Some application fields which they are used are

below:

Glass Heating

Food Baking Ovens

Plastic Incubators

Petro-Chemistry Storages

Textile, Automative Air Conditioning

Machine Production Industries Etc...

Etc...

Application Fields Applications

Operating Temperature :

Max. Operating Hum idity :

Altitude :

-20 to 70 °C

90 Rh (non-condensing)

Up to 2000 m.

Forbidden Conditions:

Corrosive atmosphere, Explosive atmosphere,

Home applications (The unit is only for industrial applications)

1.1 Operating Conditions

ESM-1520N

Standard

Control Output

NTC

J or K Type TC

2-wire PT 100

PTC

2-wire PT 1000

Output-2

( )

Relay or SSR Output Alarm Output

Heating or Cooling

Function

PID or ON/OFF O peration

Temperature Sensor

Input

Power Supply

Input

Standard

230 V (±%15) , 50/60Hz

Optional Sup ply Input

Output-1

(SSR Driver Output)

EMKO Elektronik warrants that the equipment delivered is free from defects in material and

workmanship. This warranty is provided for a period of two years. The warranty period starts from

the delivery date. This warranty is in force if duty and responsibilities which are determined in

warranty document and instruction manual performs by the customer completely.

1.5 Maintenance

Repairs should only be performed by trained and specialized personnel. Cut power to the device

before accessing internal parts.

Do not clean the case with hydrocarbon-based solvents (Petrol, Trichlorethylene etc.). Use of

these solvents can reduce the mechanical reliability of the device. Use a cloth dampened in ethyl

alcohol or water to clean the external plastic case.

2 General Description

2.1 Front View and Dimensions of ESM-1520N Temperature Controller

4.4 Entering To The Programming Mode, Chang i ng and Saving Parameters

iIf no operation is performed in Programming mode for 20 seconds, device turns to

operation screen automatically

Press E nter b utto n for

accessing to t he

password enterin g

screen.

Enter programming

mode accessing

password with

increment a nd

decrement buttons Press E nter b utto n

for accessing to the

parameters

Operation Screen

Password Entering

Screeen

When SET button is pressed for 5

seconds, “P” led start s to blink. If

programming mod e entering password is

different from 0, programming mode

enteri ng scre en will be observed.

5 secs

Programming Mode

Entering Screen

Note-2: Parameters can be observed by pressing ENTER button in

password entering screen without entering the programming mode

entering password. But parameters can not be changed.

Note-1: If programming mode acce ssing password i s 0, hystere sis

screen is observed instead of Pr ogramming screen

accessing password

Password Entering

Screeen

Para meter is accessed

by pressing Ent er

button. If set button is

pressed, next

parameter is shown.

Pnt Parameter

Value

Change the

parameter with

increment a nd

decrement buttons

6. Ordering Infor mation

All order information of ESM-1520N

Temperature Controller are given on the

table at left. User may form appropriate

device configuration from information and

codes that at the table and convert it to the

ordering codes.

Firstly, supply voltage then other

specifications must be determined. Please

fill the order code blanks according to your

needs.

Please contact us, if your needs are

out of the standards.

Symbol means Vac,

Symbol means Vdc,

Symbol means Vac/dc

A BC D E FG HI /

U V W Z/

/0 00 2 0 0

01 Relay Output ( resistive load 5 A@250 V , 1 NO + 1NC )

Output-2FG

Supply VoltageA

Input TypeBC Scale(°C)

ESM-1520N (77x35 DIN Size)

24V ( ± 15% ) 50/60Hz - 2.5VA

115V ( ± 15% ) 50/60 Hz - 2.5VA

230V ( ± 1 5% ) 50/60Hz - 2.5VA

10...30 V - 2.5W

9 Customer

02 SSR Driver Output (Maximum 20 mA, 17 V )

J ,Fe CuNi IEC584.1(ITS90)

PTC (Note-1) (Note-2) -50°C 150°C

0°C 800°C

-19.9°C 99.9°CPT 100 , IEC751(ITS90)

10 K ,NiCr Ni IEC584.1(ITS90)

-50°C 400°C

0°C 999°C

11 PT 100 , IEC751(ITS90)

14 -50°C 400°CPT 10 00 , IEC751(ITS90)

13 -19.9°C 99.9°CPT 1000 , IEC751(ITS90)

Temp. Sensor which is given with ESM 1520N

0None

1PTC-M6L40.K1.5 (PTC Air Probe with 1.5 m silicon cable)

2PTCS-M6L30.K1.5.1/8” (PTC Liquid Probe with 1.5 m silicon

cable)

Customer

3NTC-M5L20.K1.5 (NTC Probe, thermoplastic moulded with

1.5 m cable for cooli ng application)

4NTC-M6L50.K1.5 (NTC Probe, stainless steel housing with

1.5 m cable for cooli ng application)

Note-2 : If input type is selected PTC or NTC (BC = 12, 18 ),

Temperature sensor is given with the device. For this reason,

If input type is selected as PT C , sensor type (V = 0,1 or 2) or

If input type is selected as N TC , sensor type (V = 0,3 or 4) must b e

declared in ordering information.

-50°C 100°C18 NTC (Note-1) (Note-2)

24V ( -15%,+10% ) 50/60Hz - 2.5VA

5. Failure Messages in ESM-1520N Temperature Controller

Probe defect in analogue inputs. Sensor connection is wrong or

there is no sensor connection.

Your Technology Partner

www.emkoelektronik.com.tr

Thank you ve ry much for your preference to

use Emko Elektronik products, please visit our

web page to d ownload user manual.

Rail Lock Apparatus

35 mm / 1.38 i nch

90 mm / 3.54 inch

90 mm / 3.54 i nch

61.2 mm / 2.40 inch

35.7 mm / 1.40 inch

46.5 mm / 1.83 inch

2 3 41 5

7891011

Note-1 : Selectable decimal type for PTC and NTC via parameter

(Scale : -19,9...99, 9°C)

115 V (±%15), 50/60Hz

24 V (±%15), 50/60Hz

10...30 V

24 V (-%15, + ), 50/60Hz

%10

100-240V ( -15%, +1 0% ), 50/60Hz

100-240V ( -15%, +10% ) 50/ 60Hz - 2.5VA

2SSR Driver Output (Maximum 20 mA, 17 V )

Output-1E

ESM-1520-N

Manufacturer Inf ormation:

Repair and maintenance service information:

Bursa Organize Sanayi Bölgesi, (Fethiye OSB Mah.)

Phone : (224) 261 1900

Fax : (224) 261 1912

Bursa Organize Sanayi Bölgesi, (Fethiye OSB Mah.)

Phone : (224) 261 1900

Fax : (224) 261 1912

1.6 Manufacturer Company

4.5 Alarm Types

Proce ss High

Alarm

Output

Proce ss Low

Alarm

Deviation High

Alarm

Deviation Low

Alarm

Deviation Band

Alarm

Deviation Range

Alarm

OFF

Alarm

Output

Process Value

OFF

Alarm

Output

Process Value

OFF

Alarm

Output

Process Value

( + )

OFF

Process Value

OFF

Alarm

Output

Process Value

OFF

Alarm

Output

Process Value

OFF

Alarm

Output

Process Value

Deviation Range

High Alarm

Process

Set

Alarm

Hysteresis

Alarm

Set

Alarm

Set

Alarm

Hysteresis

Process

Set

Alarm

Set

Alarm

Hysteresis

( - )

Process

Set

Alarm

Set

Process

Set

Alarm

Hysteresis

( - )

Process

Set

Alarm

Set ( + )

Process

Set

Alarm

Set

Alarm

Hysteresis

Alarm

Hysteresis

Process

Set

( - )

Process

Set

Alarm

Set ( + )

Process

Set

Alarm

Set

Alarm

Hysteresis

Alarm

Hysteresis

Process

Set

( - )

Process

Set

Alarm

Set

Alarm

Hysteresis

ESM-1520-N

2.5 Pane l Mounting

2.2 Installation onto the Rail

cDuring installation onto the rail, care should be taken to avoid injury from

mechanical part of the system. These precautions for the safety of the person

who does the rai mounting.

The unit is designed for rail mounting.

1- Put into the unit upper side of the

rail properly.

2- Pull down the rail lock apparatus

via a screw driver.

3.-Push the unit from the underside

for mounting to the rail.

2.3 Removing from the Rail

1- Pull down the rail lock apparatus

via a screw driver.

ull up the unit to remove from the

rail.

2- Pull the unit from the underside to

seperate the rail lock apparatus from

the rail

3.- P

Before starting to remove the unit from the rail, power off the unit and the

related system.

Supply Voltage I nput

3. Electrical Wiring Diagram

3.1 Supply Volta ge Inp ut Connection of the Device

Make sure that the power supply voltage is same indicated on the instrument.

Switch on the power supply only after that all the electrical connection have been completed.

Supply voltage range must be determined in order. While installing the unit, supply voltage range must be

controlled and appropriate supply voltage must be applied to the unit. Controlling prevents damages in unit

and system and possible accidents as a result of incorrect supply voltage.

There is no power supply switch or fuse on the device. So a power supply switch and a fuse must be added

to the supply voltage input. Power supply switch and fuse must be put to a place where user can reach

easily. Power supply switch must be two poled for seperating phase and neutral. On/Off condition of power

supply switch is very important in electrical connection. On/Off condition of power supply switch must be

signed for preventing the wrong connection.

Temperature Sensor Input

(T C, NTC, PTC, PT-100 or PT-1000)

Supply Voltage

100-240 V (-15%,+10%) 50/60 Hz

230 V (± 15%) 50/60 Hz

115 V (± 15%) 50/60 Hz

24 V (± 15%) 50/60 Hz

24 V (-15%,+10%) 50/60 Hz

10...30 V

Note-2

External

Fuse

(1 A T)

Note-1

Power

Supply

Switch

Note-1:

“ ” “ ”L is (+), N is (-) for 10...30V and

24V Supply Voltage

Note-2: External Fuse is recommended

Note-3: External fuse must be on phase connection in

supply input.

Note-4: External fuse must be on (+) line connection in

supply input.

100-240 V (-15%,+10%) 50/60 Hz

V ( ± %15 ) 50/60 Hz

24 V ( ± %15 ) 50/60 Hz

24 V ( -%15, +%10 ) 50/60 H z

10...30 V

230

115

3.2.2 PTC a nd NTC Connection

3.2.1 TC (Thermocouple ) Connection

3.2 Temperature Sensor Input Connection

PTC

Input resistance is greater than 10M .

Pay attention the cable colours of PTC probe while doing the PTC probe

connection.

WHITERED

Connect the wires with the polarity as shown in

the figure left.

Always use compensation wire corresponding

to the thermocouple used. If present, the shield

must be connected to a proper ground.

Input resistance is greater than 10M

NTC

Input resistance is greater than 10M .

3.2.3 and PT-1000 ConnectionPT-100

PT-1000

PT-100

*It is used to decrease the value in the

Set screen and Programming mode

4. Front Panel Definition and Accessin g to the Menus

When power is first applied to the temperature controller, software revision number is shown on

the displays.

4.1 Observation of Software Revision on the Displays

“ ”r RevisionÞSoftware

revision

Number

Operation Screen is shown

If there is an unexpected situation while opening the device, power off the

device and inform a qualified personnel.

It is used to increase the

value in the Set screen and

Programming mode

It is used to enter to the SET value

changing mode, programming mode

and used as OK button

Displays Temperature

Value,Temperature Set

Value and Para me ters

Indicates that device is in SET

value changing mode

Blinks in programming

mode

Led indi cation of Output

is active (If blinks, Compressor

protection time is active)

4.2 Changing and Saving Temperature Set Value / Alarm Set Value

iIf no operation is performed in Set value mode for 20 seconds, device turns to

operation screen automatically.

11 12

NTC, PTC, PT-100, PT1000

4.3 Program Parameters

Decimal Seperator Enabling Parameter ( Default = 0 )

Disable.

Enable.

Note : If sensor input type is selected PTC or NTC (BC= 12 or 18) is observed.

Note : When Pnt parameter is changed, change Set, hSt, SuL, SuH, oFt parameters with appropriate values.

Note-6: Supply cables must comply with the requirements

of IEC 60277 or IEC 60245.

Note-5: Stranded cable cross section: 1,5mm²,

Solid cable cross-section: 2,5mm²

The stripping length is 7 to 9 mm.

ESM-1520-N

Relay or SSR Driver Output

For SSR Output

(+) (-)

L(+) N(-)

2 3 41 5

5 A@250 V

NOC

This le d indic ates that alarm

output relay is a ctive

*In the main operation scre en; if

this button pressed,

tempera ture set value will be

displayed. Value can be

changed using increment and

decrement buttons. When Enter

button pre ssed, value is saved

and alarm set value is

displayed. Value can be

changed using increment and

decrement buttons. When Enter

button pressed, alarm set value

is saved and returns back to

main operating screen.

*To access the programming

screen; in the main operati on

screen, pres s this button for 5

seconds

ESM-1520-N

When SET button is

pressed, SV LED

lights on and

Temperature Set

value is sho wn on the

displays.

Change the Temper ature Set

value with incre ment and

decrement b utto ns.

Press ENTER button

for saving the

Temperature Set

value and to change

the Alarm Set value

SV LED lights off and main

operation screen is shown.

Operation Scre en TEMPERATURE SET Value Screen

TEMPERATURE SET Value Screen ALARM SET Value Screen

SET value is can be adjusted from minimum set value parameter to maximum set value

parameter , Which can be accessed from programming parameters.

ESM-1520-N

Change the Alarm Set value with

increment and decrement buttons.

ESM-1520-N

ALARM SET Value Screen

ESM-1520-N

Operation Scre en

Press ENT ER button

for saving the Alarm

Set value

Operating Ty pe Parameter ( Default = 0 )

Heating

Cooling

Note: If operating type is selected cooling and PID parameters are Device operates with

On-Off control.

parameter skipped.

Temperature Control Selection Parameter On/Off or PID ( Default = 0 )

On - Off selected.

PID selected

Note: If this parameter is select 0, PID parameters will be not observed.If this parameter select 1, Parameter

will be not observed.

Note-1: If this parameter is select the temperature must be lower than temperature set value. If this

condition is not o key

If this parameter is select the temperature

is seen on the main screen for 10 seconds.

must be greater than temperature set value at least

5% of the full s cale. If this condition is not okey is seen on the main sc reen for 10 seconds.

Note-2:

Tune Selection Parameter ( Default = no )

Device does not do Tune operation.

Device does Auto-Tune operation

Device does Self-Tune operation

PID - Proportional Control Parameter ( Default = 10.0 )

This parameter can be ad j usted from %1.0 to %99.9

PID-Integral Parameter( Default = 100 )

This parameter value can be adjusted from 0 to 999

PID-Derivativel Parameter ( Default = 25.0 )

This parameter value can be adjusted from 0.0 to 99.9

PID-Period parameter( Default = 10 )

This parameter value can be adjust from 0 to 150 second.

Operation Scale Min i mum Parameter ( Default = Minimum Value of Device Scal e )

This parameter value can be adjusted from minimum value of device scale to operation scale

maximum parameter

Operation Scale Maximum Para meter ( Default = M aximum Value of Device Sc ale )

This parameter value can be adjusted from operation scale mi nimum par ameter to maximum

value of the device scale.

Hysteresis Parameter for Compressor Output ( Default = 3 )

from 1 to 20°C for NTC (-50°C, 100°C) or PTC (-50°C, 150°C) or J Type TC ( 0°C, 800°C ) or K Type TC

( 0°C, 999°C or PT-100 Type ( -50°C,400°C ) or PT-1000 Type ( -50°C,400°C )

from 0.1 to 10.0°C for NTC(-19.9°C,99.9°C) or PTC (-19.9°C,99.9°C) or PT-100 (-19.9°C,99.9°C) or

PT-1000 (-19.9°C,99.9°C)

In ON/OFF control algorithm, temperature value is tried to keep

equal to set value by opening or closing the last control element.

ON/OFF controlled system, temperature value oscillates

continuously. Temperature value s oscillation period or amplitude’

around set value changes according to controlled system. For

reducing oscillation period of temperature value, a threshold zone

is formed below or around set value and this zone is named

hysteresis. ON

OFF

Temperature

Control

Output

Set

HSt

Time

HSt

Time

Minimum Set Value Parameter ( Default =Minimum value of device scale )

Set value can not be lower than this value. This parameter value can be adjusted from minimum value

of device scale to maximum set value parameter .

Maximum Set Value Parameter ( Default = Maximum value of device scale )

Set value can not be greater than this value. This parameter value can be adjusted from minimum set

value to maximum value of the device scale.

Sensor Offset Parameter ( Default = 0 )

fro m -20 to 20 °C for NTC(-50°C, 100°C) o r PTC(-50°C, 150°C) o r J Type TC (0°C,800°C) or K

Typ e TC (0°C,999°C) or PT-100(-50°C, 400°C)or PT-1000 (-50°C, 400°C) from -10.0 to 10.0°C

for NTC(-19.9°C,99.9°C) or P TC(-19.9°C,99.9°C) or PT-100 (-19.9°C,99.9°C) or PT-1000

(-19.9°C,99.9°C)

Compressor Start Delay at Power On Parameter ( Default = 0)

When power is first applied to the device, compressor is on when this time delay is expired. It can be

adjusted from 0 to 20 minutes.

Compressor Stop-Start Delay Parameter ( Default = 0)

When compressor is inactive, this time delay must be expired for activation of the compressor. It can

be adjusted from 0 to 20 minutes.

Compressor Start-Start Delay Parameter ( Default = 0)

This time delay must be expired between two activation of the compressor. It can be adjusted from 0 to

20 minutes.

Sensor Defe ct Parameter ( Default = 0 )

Compressor is OFF in case of sensor defect.

Compressor is ON in case of sensor defect.

Compressor operates periodically according to and Time periods in case of

sensor defect.

Compressor is active du ring this time period in case of p robe defect ( Default = 0 )

If probe defect parameter is 2, then this parameter is observed. It can be adjusted from 0 to 99 minutes.

Compressor is active du ring this time period in case of p robe defect ( Default = 0 )

If probe defect parameter is 2, then this parameter is observed. It can be adjusted from 0 to 99 minutes.

Temperature Alarm Function Selection Parameter ( Default =1 )

Alarm function is inactive.

Process Low alarm selected.

Process High alarm selected.

Deviation High alarm selected.

Deviation Low alarm selected.

Deviation Band alarm selected.

Deviation Range alarm selected.

Deviation Range High alarm selected.

Note: If this parameter is select 0, , , , , , and parameters will be not observed.

Temperature Alarm Parameter

This parameter value can be programmed between temperature minimum alarm set

parameter and temperature alarm set maximum parameter.

Set ( Default =80 )

5 A@ 250 V

Temperature Alarm Parameter

This parameter value can be adjusted form 0.1 to %50 of the device scale if Pnt parameter is 1, 1 to

%50 of the device scale if Pnt parameter is 0.

Hysteresis ( Default =3 )

Programming Section Accessing Password

( Default = 0 )

It is used for accessing to the programming section. It can be adjusted from 0 to 9999. If it is selected 0,

password will not be asked

Mode-1 (The increase or decrease in values firstly occurs one by ones, then ten by tens, and

finally hundred by hundreds.

Increment/Decrement M ode ( Default = 0 )Selection Par ame ter

Mode-2 (The rate of increase or decrease of the values accelerates over time.)

Temperature Minimum A l arm Para meter ( Default =Minimum Value of Devic e Scale )

If temperature ala rm is active, this parameter value can be adjusted from operation scale minimum

parameter to temperature alarm set maximum p arameter value .

Temperature Alarm Maximum Parameter ( Default = Maximum Value of Device Scale )

If temperature ala rm is active, this parameter value can be adjusted from temperature alarm set

value parameter to operation sca le maximum parameter

Temperature Alarm On Delay Time Parameter( Default = 0 )

Temperature alarm on delay time can be defined with this parameter.

It can be adjusted from 0 to 99 minutes.

Temperature Alarm Off Delay Time Parameter( Default = 0 )

Temperature alarm off delay time can be defined with this parameter.

It can be adjusted from 0 to 99 minutes. If it is higher than 99 is seen on the screen and alarm

latching output is selected. In alarm latching output mode, in order to make passive alarm output,

press DECREMENT button at main screen.

Temperature Alarm DelayAfter Power On Parameter

When power is first applied to the device, this time delay must be expired for activation of temperature

alarm. It can be adjusted from 0 to 99 minutes.

( Default = 0 )

, , , , and Parameters are observed if Operation type is

selected Cooling .“ ”

Termékspecifikációk

Márka:	Emko
Kategória:	hőmérséklet szabályozó
Modell:	ESM-1520-N

Szüksége van segítségre?

Ha segítségre van szüksége Emko ESM-1520-N, tegyen fel kérdést alább, és más felhasználók válaszolnak Önnek

Az Ön neve*

Az Ön e-mail címe*

Írja ide kérdését

Útmutatók hőmérséklet szabályozó Emko

Emko ESM-1520-N Útmutató

28 Augusztus 2024

Emko ECO PID+ Útmutató

28 Augusztus 2024

Emko Eco PID Útmutató

28 Augusztus 2024

Emko Eco Lite Útmutató

28 Augusztus 2024

Emko CHANNEL8A-N Útmutató

25 Augusztus 2024

Emko ESM-7720 Útmutató

25 Augusztus 2024

Emko ESM-3711-CN Útmutató

25 Augusztus 2024

Emko ESM-4410 Útmutató

25 Augusztus 2024

Emko ESM-4435 Útmutató

25 Augusztus 2024

Emko ESM-3720 Útmutató

17 Augusztus 2024

Útmutatók hőmérséklet szabályozó

Legújabb útmutatók hőmérséklet szabályozó

IFM LT8924 Útmutató

6 December 2024

IFM OW5020 Útmutató

5 December 2024

Jung TVA230NCWW Útmutató

2 Október 2024

Jung TRGO2 Útmutató

30 Szeptember 2024

Technoline WS 9245 Útmutató

28 Szeptember 2024

Voltcraft ETC-200 Útmutató

21 Szeptember 2024

Jung TRME2 Útmutató

20 Szeptember 2024

Jung TRCD241 Útmutató

19 Szeptember 2024

Dimplex AR99DC1 Útmutató

18 Szeptember 2024

Fluke 7102 Útmutató

15 Szeptember 2024