Használati útmutató Emko ECO PID+

Emko hőmérséklet szabályozó ECO PID+

Olvassa el alább 📖 a magyar nyelvű használati útmutatót Emko ECO PID+ (4 oldal) a hőmérséklet szabályozó kategóriában. Ezt az útmutatót 4 ember találta hasznosnak és 2 felhasználó értékelte átlagosan 4.5 csillagra

Letöltés PDF

Oldal 1/4

Eco PID+, PID Temperature Control Un t�

- 4 d g t process (PV) and 4 d g t set (SV) d splay� � � � �

- Temperature sensor �nput (TC,RTD)

- Programmable ON/OFF, P, PI, PD and PID control forms

- Adaptat on of PID Coeff c ents to the system w th Self-Tune and Auto-Tune � � � �

- Programmable Heat ng or Cool ng Funct ons for Control Output � � �

- Selectable Alarm Funct ons for Alarm Output�

- Ser al RS485 Commun cat on (opt onal)� � � �

Introduct�on Brochure. ENG EcoPID+ 01 V00 03/22

Easy Access D agram For Program Parameters�

Panel Mount ng�

Enter Password w th ncrement� �

or decrement buttons.

Approve password

w th Enter button�

Password Screen

Eco ser es temperature controllers are des gned for measur ng and controll ng a � � � �

temperature value. They can be used n many appl cat ons w th the r TC and RTD � � � � �

temperature measurement nput, mult -funct on control outputs, selectable alarm � � �

funct ons.�

They are ma nly used � �n glass, plast c, petro-chem stry, text le, automot ve and mach ne � � � � �

product on � � �ndustr es. Accurate and advanced controll ng � �s performed w th selectable �

ON-OFF, P, PI, PD, PID and Self Tune/Auto Tune PID funct ons.�

SPECIFICATIONS

Process Input: Thermocouple (TC): J, K, R, S, T and L (IEC584.1)(ITS90)

Thermores stance (RTD): Cu-50 and PT-100 (IEC751)(ITS90)�

Measurement Range: Please refer to process �nput type select on � �n process menu

parameters sect on.�

Accuracy:

Thermocouple (TC):( ± 0.25% of full scale or ± 3ºC, wh ch one � �s greater) ±1 d g t max. � �

Thermores stance (RTD):( ± 0.25% of full scale or ± 2ºC, wh ch one � � �s greater) ±1 d g t � �

max.

Cold Junct on Compensat on:� � Automat cally ±0.1°C/1°C�

L ne Compensat on:� � Max mum 10 Ohm�

Sensor Break Protect on:� Upscale

Sampl ng Cycle: �0.1 second

Input F lter:� Programmable

Control Form: ON/OFF, P, PI, PD or PID (Control form can be programmed by the user)

OUTPUT

Process Output: Relay (5A@250V at res st ve load) or SSR Dr ver Output V� � �

(Max mum 10mA, Max. 12V )�Z

Alarm Output: Relay (5A@250V at res st ve load)V� �

SUPPLY VOLTAGE (It must be determ ned � �n order)

230V (±15%) 50/60Hz - 4VAV

115V (±15%) 50/60Hz - 4VAV

100-240V 50/60Hz - 4VAV

24V (±%15) 50/60Hz - 4VAV

24V (±%15) 50/60Hz - 4VAW

10...30V - 4W Z

DISPLAY

Process D splay:� 16 mm Red 4 d g t LED D splay� � �

Set Value D splay:� 9 mm Orange 4 d g t LED D splay� � �

Led Ind cators:� PO1 (SSR Process Output Status Led), PO2 (Relay

Process Output Status Led), AL1, AL2 (Alarm Output Status Leds),

ºC, ºF LEDs

ENVIRONMENTAL RATINGS and PHYSICAL SPECIFICATIONS

Operat ng Temperature:� 0...50ºC

Hum d ty :� � 0-90%RH (none condens ng)�

Mechan cal Impacts: �1Joule (IK06)

Protect on Class: �NEMA 4X (IP65 at front, IP20 at rear)

We ght:� 150 gr.

D mens on:� � 48 x 48 mm, Depth: 86,5 mm

Panel CutOut: 46 x 46 mm

*1 - ON/OFF Hysteres s parameter s not act ve unless parameter s set as .� � � �

*2 - Soft Start parameters( , , ) s not act ve unless parameter s set as .� � �

*3 - Soft Start Control Output and Soft Start Control T me parameters s not act ve f parameter� � � �

s set as .�

*4 - PID control parameters are not act ve unless parameter s set as .� �

*5 - Alarm-2 parameters are not act ve f parameter s set as .� � �

*6 - Commun cat on parameters are not act ve on dev ces have no commun cat on module.� � � � � �

*7 - If s d fferent from 0 and user enters to program menu w thout enter ng the password� � � �

Prot menu s not shown.�

Note: User can ex t from any parameter screen w thout sav ng the values by press ng button. If � � � �

no operat on for 120 seconds, dev ce automat cally return to ma n screen. � � � �

Easy Access D agram For Sensor Break Output�

Value From Ma n Screen�

Change the sensor break

output value w th ncrement� �

or decrement buttons.

Press Enter button to save

new sensor break output value

and ex t.�

Ma n Screen Ma n Screen� �

Note1: User can ex t from parameter screen w thout sav ng the � � �

values by press ng button. If no operat on for 120 seconds, dev ce � � �

automat cally ex ts from parameter screen.� �

Note2: Sensor break output value can be adjusted on programm ng �

sect on too.�

Tune Operat on�

Start ng the Tune operat on� �

1- Enter to the parameter n menu and select �

or ,then press button for sav ng parameter and turn to ma n � �

screen. Or eas ly press button for 3 seconds* n ma n screen.� � �

2- Observe that bl nks n set d splay.� � �

*Only Self Tune can be started by th s way.�

Cancel ng Tune operat on:� �

1- If sensor breaks;

2- If tune operat on can not be completed n 8 hours;� �

3- Wh le heat ng self tune s runn ng, f process value becomes � � � � �

greater than process set value;

4- Wh le cool ng self tune s runn ng, f process value becomes less � � � � �

than process set value;

5- Wh le tune operat on s runn ng, f user changes the process set � � � � �

value;

6- Wh le tune operat on s runn ng, f user changes the � � � � �

parameter n menu; �

Then tune operat on s canceled, dev ce cont nues to run w th former � � � � �

PID parameters w thout chang ng PID parameters.� �

PID TEMPERATURE CONTROL UNIT

PID+

Eco

D mens ons� �

48 mm / 1.89 nch�

6 mm / 0.24 nch�80,52 mm / 3.17 nch�

Max mum 9 mm / 0.35 nch� �

1- Before mount ng the dev ce n your panel, � � �

make sure that the cutout s of the r ght s ze.� � �

2- Check front panel gasket pos t on.� �

3- Insert the dev ce through the cutout. If the �

mount ng clamps are on the un t, put out them � �

before nsert ng the un t to the panel.� � �

4- Insert the mount ng clamps to the two of �

des gnated holes that located four s des of � �

dev ce. �

5- Drag the mount ng clamps n d rect on 5 � � � �

unt l the dev ce completely mmob le w th n the � � � � � �

panel.

6- In order to remove dev ce push on the �

mount ng clamp as shown w th arrow 6 and � �

pull back.

Access and Change Set Values

Press ncrement or decrement�

button to change process set value.

Press Enter button to save new

set value and return the ma n screen.�

Ma n ScreenMa n Screen ��

Temperature Set Value Parameter (Default: 200) MODBUS ADDRESS: 40000

Note-1: User can ex t from set value sect on w thout sav ng the values by press ng button. If no � � � � �

operat on for 120 seconds, dev ce automat cally ex ts from Set Value sect on.� � � � �

Note-2: Set value can be adjusted between Set Value Low and H gh L m t ( - ).� � �

Press Program button

to access password screen.

Electr cal W r ngs� � �

To reduce the effect of electr cal no se on dev ce, low voltage l ne (espec ally sensor� � � � �

� � � � � �nput cable) w r ng must be separetely from h gh current and voltage l ne. If poss ble,

use sh elded cable and sh eld must be connected to ground only one s de.� � �

Note-1: External Fuse s recommended.�

Note-2: Stranded cable cross sect on: 1,5mm², Sol d cable cross-sect on: 2,5mm²� � �

The str pp ng length s 7mm to 9mm.� � �

Note-3: Supply cables must comply w th the requ rements of IEC 60277 or IEC 60245.� �

It s adv sed to use a two-pole supply sw tch, des gnated for th s dev ce, w th open/� � � � � � �

closed pos t ons marked, n order to cut the power. It must be placed on the supply � � �

� � �nput of the dev ce at a place where the user can eas ly reach.

V External fuse must be on phase connect on of the supply nput.� �

Z External fuse must be on (+) l ne connect on of the supply nput.� � �

Make sure that the power supply voltage range s su table for the dev ce.� � �

Sw tch on the power supply only after all the electr cal connect ons are n place.� � � �

PO1

(Process Output 1)

SSR Output

12V

Max. 10mA

AL1

(Alarm Output 1)

AL2 / PO2

(Alarm Output 2 or

Process Output 2)

Process

Input

5A@250V

Ser al Commun cat on� � �

(RS485, Modbus RTU) A+

B-

PID+

Eco

PT-100

Supply

Sw tch�

Supply

Voltage

1A T

Fuse

NOTE-1

AL1 / PO2

(Alarm Output 1 or

Process Output 2)

Process

Input

5A@250V

PT-100

The Dev ce �

w th Two Relays�

The Dev ce �

w th One Relay�

Çal ma Ekranış ı

*2,3

*7*6

Warranty

EMKO Elektron k warrants that the equ pment del vered s free from � � � �

defects n mater al and workmansh p. Th s warranty s prov ded for a � � � � � �

per od of two years. The warranty per od starts from the del very � � �

date.

Th s warranty s n force f duty and respons b l t es wh ch are � � � � � � � � �

determ ned n warranty document and nstruct on manual performs � � � �

by the customer completely.

Ma ntenance�

Repa rs should only be performed by tra ned and spec al zed � � � �

personnel. Cut power to the dev ce before access ng nternal parts. � � �

Do not clean the case w th hydrocarbon-based solvents (Petrol, �

Tr chlorethylene etc.). Use of these solvents can reduce the �

mechan cal rel ab l ty of the dev ce. Use a cloth dampened n ethyl � � � � � �

alcohol or water to clean the external plast c case.�

Other Informat ons�

Manufacturer Informat on:�

Emko Elektron k Sanay ve T caret A. .� � � Ş

Bursa Organ ze Sanay Bölges , (Feth ye OSB Mah.)� � � �

Al Osman Sönmez Bulvar , 2.Sokak, No: 3 16215 BURSA/TÜRK YE� ı İ

Phone : +90 224 261 1900

Fax : +90 224 261 1912

Repa r and Ma ntenance Serv ce Informat on:� � � �

Emko Elektron k Sanay ve T caret A. .� � � Ş

Bursa Organ ze Sanay Bölges , (Feth ye OSB Mah.)� � � �

Al Osman Sönmez Bulvar , 2.Sokak, No: 3 16215 BURSA/TÜRK YE� ı İ

Phone: +90 224 261 1900

Fax : +90 224 261 1912

10...30V - 4WZ

115V (±%15) 50/60Hz - 4VAV

230V (±%15) 50/60Hz - 4VAV

100-240V 50/60Hz - 4VA1 V

24V (±%15) 50/60Hz - 4VAV

Customer Spec f ed� �

24V (±%15) 50/60Hz - 4VA2 W

Supply VoltageB

Before comm ss on ng the dev ce, parameters must be set n � � � � �

accordance w th des red use. Incomplete or ncorrect conf gurat on � � � � �

can cause dangerous st uat ons.� �

Because of l m ted mechan cal l fe of relay output contact, SSR � � � �

output s recommended wh ch the dev ce use PID control algor tm. � � � �

The dev ce w th ON/OFF control algor tm, hysteres s parameter must � � � �

be set a su table value for your system, to avo d too much relay � �

sw tch ng.� �

Vac,

Vdc,

Vdc or Vac can be appl ed�

: Commun cat on Parameters � � (Only for dev ces w th RS-485 com.)� �

: Protec on Menu Parameters�

: Commun cat on access ng address of dev ce. (Default: 1) Modbus � � � �

Address: 40056

: Commun cat on Baud Rate. (Default: 3) Modbus Address: 40057� �

: 1200 Baud Rate.

: 2400 Baud Rate.

: 4800 Baud Rate.

: 9600 Baud Rate.

: 19200 Baud Rate.

: 38400 Baud Rate.

: Par ty Select on for Commun cat on. (Default: 0) Modbus Address: 40058� � � �

: No Par ty.�

: Odd Par ty.�

: Even Par ty.�

: Stop B t Select on for Commun cat on. (Default: 0) Modbus Address: 40059� � � �

: 1 Stop B t.�

: 2 Stop B t.�

: Password for access ng to the programm ng sect on. It can be adjusted from 0 to � � �

9999. If s 0, password screen s not seen. If s d fferent from 0 and user � � � �

enters to the menu pages w thout enter ng the password, all the menus can be � �

observed except protect on menu . But dev ce does not allow to do any changes � �

�n parameters. (Default: 0) Modbus Address: 40063

: User default parameters. Th s parameter s used for sav ng all parameters to � � �

restore later or restore all parameters saved before. If s chosen, all parameters �

saved before are restored. If s chosen, all parameters saved to restore later. If�

� � �s chosen, noth ng s changed. (Default: ) Modbus Address: 40064

: Th s parameter s used for restore factory defaults. If s chosen, factory � � �

defaults parameters restored. If s chosen, noth ng s changed. (Default: ) � � �

Modbus Address: 40065

Remove all nput/output connect ons on term nals before restor ng � � � �

parameters to user/factory defaults.

Modbus Addresses of Dev ce Operat on Info. (Read Input Reg ster)� � �

Modbus Address: 30000

Modbus Address: 30001

Modbus Address: 30002

D splayed Temperature Value�

Status of LEDs: b t.1 , b t.2 , b t.9 �ALR1 �ALR2 �°C

b t.10 , b t.11 , b t.12 �°F �PO2 �PO1

Status of Dev ce: b t.0 Sensor Break Status� �

Alarm Types

Alarm

Set

Alarm

Hysteres s�

Alarm

Hysteres s�

Alarm

Set

Process

Set

Process

Set

Alarm

Set

Alarm

Hysteres s�

Alarm

Hysteres s�

Process

Set

Process

Set

Alarm

Set

Alarm

Output

Alarm

Output

Alarm

Output

Alarm

Output

Process Value

Process H gh�

Alarm

Process Low

Alarm

Dev at on H gh� � �

Alarm

Dev at on Low� �

Alarm

: Alarm-1 set value. (Default: 300) Modbus Address: 40036

: Alarm-1 hysteres s value. It can be adjusted from %0 to %50 of the scale�

( - ). (Default: 0) Modbus Address: 40037

: Alarm-1 type select on. (Default: ) Modbus Address: 40038�

: Alarm-1 set low l m t parameter. It can be adjusted from operat on scale m n mum � � � � �

to alarm-1 set h gh l m t. (Default: 0) Modbus Address: 40039� � �

: Alarm-1 set h gh l m t parameter. It can be adjusted from alarm-1 set low l m t to � � � � �

operat on scale m n mum. (Default: 500) Modbus Address: 40040� � �

: Alarm-1 on Delay T me. It can be adjusted from 0 to 9999 seconds. (Default: 0) �

Modbus Address: 40041

: Alarm-1 off Delay T me. It can be adjusted from 0 to 9998 seconds. If t s h gher � � � �

than 9998, s seen on the screen and alarm latch ng output s selected. In alarm � � �

latch ng output mode n order to make pass ve alarm outputs, press enter button at � � �

ma n screen. (Default: 0) Modbus Address: 40042�

: Alarm-1 Menu Parameters

PID menu parameters can be seen only f parameter s .� �

: If tune parameter s set to or , dev ce start to calculate PID � �

parameters automat cally. (Default: ) Modbus Address: 40027�

: Proport onal band. It can be adjusted from %1.0 to %100.0. (Default: 10.0) �

Modbus Address: 40028

: Integral T me. It can be adjusted from 0 to 3600 second. (Default: 100) Modbus �

Address: 40029

: Der vat ve T me. It can be adjusted from 0.0 to 999.9 second. (Default: 25.0) � � �

Modbus Address: 40030

: Output Control Per od. It can be adjusted from 0.5 to 150 second. (Default: 1.0) �

Modbus Address: 40031

: Set value offset. (Set + ) s used as set value n PID calculat ons. Th s � � � �

parameter s used for sh ft ng the proport onal band. It can be adjusted from (- /2) to � � � �

( /2). (Default: 0) Modbus Address: 40032

: PID Menu Parameters



: Alarm-2 Menu Parameters (Only for dev ces w th two relays)� �

Alarm-2 menu parameters can be seen only f parameter s .� �

: Alarm-2 set value. (Default: 400) Modbus Address: 40046

: Alarm-2 hysteres s value. It can be adjusted from %0 to %50 of the Scale�

( - ). (Default: 0) Modbus Address: 40047

: Alarm-2 type select on. (Default: ) Modbus Address: 40048�

: Alarm-2 set low l m t parameter. It can be adjusted from operat on scale m n mum � � � � �

to alarm-2 set h gh l m t. (Default: 0) Modbus Address: 40049� � �

: Alarm-2 set h gh l m t parameter. It can be adjusted from alarm-2 set low l m t to � � � � �

operat on scale max mum. (Default: 500) Modbus Address: 40050� �

: Alarm-2 on delay t me. It can be adjusted from 0 to 9999 seconds. (Default: 0) �

Modbus Address: 40051

: Alarm-2 off delay t me. It can be adjusted from 0 to 9998 seconds. If t s h gher � � � �

than 9998, s seen on the screen and Alarm Latch ng Output s selected. In � � �

alarm latch ng output mode n order to make pass ve alarm outputs, press enter � � �

button at ma n screen. (Default: 0) Modbus Address: 40052�

Installat on�

In package,

-One p ece un t� �

-Two p eces mount ng clamp� �

-One p ece nstruct on manual� � �

A v sual nspect on of th s product for poss ble damage occured � � � � �

dur ng sh pment s recommended before nstallat on. It s your � � � � � �

respons b l ty to ensure that qual f ed mechan cal and electr cal � � � � � � �

techn c ans nstall th s product.� � � �

If there s danger of ser ous acc dent result ng from a fa lure or defect � � � � �

� � � � �n th s un t, power off the system and the electr cal connect on of the

dev ce from the system.�

The un t s normally suppl ed w thout a power sw tch or a fuse. Use � � � � �

power sw tch and fuse as requ red.� �

Be sure to use the rated power supply voltage to protect the un t �

aga nst damage and to prevent fa lure.� �

Keep the power off unt l all of the w r ng s completed so that electr c � � � � �

shock and trouble w th the un t can be prevented.� �

Never attempt to d sassemble, mod fy or repa r th s un t. Tamper ng � � � � � �

w th the un t may results n malfunct on, electr c shock or f re.� � � � � �

Do not use the un t n combust ble or explos ve gaseous � � � �

atmospheres. Dur ng the equ pment s putted n hole on the metal � � � �

panel wh le mechan cal nstallat on some metal burrs can cause � � � �

�njury on hands, you must be careful.

Montage of the product on a system must be done w th t’s mount ng � � �

clamp. Do not do the montage of the dev ce w th nappropr ate � � � �

mount ng clamp. Be sure that dev ce w ll not fall wh le do ng the � � � � �

montage.

It s your respons b l ty f th s equ pment s used n a manner not � � � � � � � � �

spec f ed n th s nstruct on manual. � � � � � �

Before beg nn ng nstallat on of th s product, please � � � � �

read the nstruct on manual and warn ngs below � � �

carefully.

Error Messages

Dev at on Range� �

H gh Alarm�

Process

Set

Alarm

Set

Process

Set

Alarm

Hysteres s�

Alarm

Output

Process Value

Process

Set

Alarm

Set

Process

Set

Process

Set

Alarm

Set

Alarm

Hysteres s�

Alarm

Hysteres s�

Alarm

Output

Process Value

Dev at on Range� �

Alarm

1-Sensor fa lure n analog nputs. Sensor connect on s wrong or there � � � � �

� �s no sensor connect on.

2-If programm ng sect on enter ng password s d fferent from “0” and � � � � �

user accesses to the parameter by enter button w thout enter ng the � �

password and wants to change a parameter, the warn ng message s � �

shown on the bottom d splay as shown on the left. Dev ce does not � �

allow to do any changes w thout enter ng the password correctly.� �

3-If value that s read from the analog nput s lower than process set � � �

low l m t parameter value ( ), value on the top d splay starts to bl nk � � � �

as shown on the p cture.�

4-If value that s read from the analog nput s h gher than process set � � � �

h gh l m t parameter value ( ), value on the top d splay starts to bl nk � � � � �

as shown on the p cture.�

5-If value that s read from the analog nput s lower than sensor scale � � �

low l m t, value on the top d splay starts to bl nk as shown on the � � � �

p cture.�

6-If value that s read from the analog nput s h gher than sensor scale � � � �

h gh l m t, value on the top d splay starts to bl nk as shown on the � � � � �

p cture.�

Process

Set

Alarm

Set

Process

Set

Process

Set

Alarm

Set

Alarm

Hysteres s�

Alarm

Hysteres s�

Alarm

Output

Process Value

Dev at on Band� �

Alarm

: Control Menu Parameters

: Th s parameter determ nes, wh ch output w ll be Process control output. If s � � � � �

chosen, process output s relay output, f s chosen, process output s SSR output. � � � �

(Default: ) Modbus Address: 40015

: Process Type Select on. It can be (Heat ng) or (Cool ng).(Default: ) � � �

Modbus Address: 40016

: Process Control Type Select on. It can be or . (Default: ) Modbus �

Address: 40017

: Hysteres s value. It can be adjusted from %0 to %50 of the Scale ( - ). �

If = , then th s parameter can be seen. (Default: 3) Modbus Address: 40018�

: Sensor Break Output Value. It can be adjusted from %0 to %100. (Default: 0.0)

Modbus Address: 40019

: The cho ce of d splayed text on process value d splay when sensor s broken.� � � �

It can be or . (Default: ) Modbus Address: 40020

: Soft Start Set value. Dev ce operates n Soft Start mode, unt l the temperature � � �

reaches Soft Start set value. If s selected, Soft Start mode s d sabled. (Default: )� � �

Modbus Address: 40021

: Soft Start Control Output. Th s parameter determ nes soft start mode control� �

output percentage. It can be adjusted from %10 to %90. (Default: 10.0) Modbus

Address: 40022

: Soft Start Control T me. Th s parameter determ nes soft start mode control t me. � � � �

(Default: 1.0) Modbus Address: 40023

: Process Menu Parameters

: Process nput type select on; (Default: ) Modbus Address: 40004� �

: J type (Fe,Cu,N ) Thermocouple , -200ºC,900ºC ; -328ºF,1652ºF�

: J type (Fe,Cu,N ) Thermocouple , -199.9ºC,900.0ºC ; -199.9ºF,999.9ºF�

: K type (N ,Cr,N ) Thermocouple , -200ºC,1300ºC ; -328ºF,2372ºF� �

: K type (N ,Cr,N ) Thermocouple , -199.9ºC,999.9ºC ; -199.9ºF,999.9ºF� �

: R type (Pt13%RhPt) Thermocouple , 0ºC,1700ºC ; 32ºF,3092ºF

: R type (Pt13%RhPt) Thermocouple , 0.0ºC,999.9ºC ; 32.0ºF,999.9ºF

: S type (Pt10%RhPt) Thermocouple , 0ºC,1700ºC ; 32ºF,3092ºF

: S type (Pt10%RhPt) Thermocouple , 0.0ºC,999.9ºC ; 32.0ºF,999.9ºF

: T type (Cu,Cu,N ) Thermocouple , -200ºC,400ºC ; -328ºF,752ºF�

: T type (Cu,Cu,N ) Thermocouple , -199.9ºC,400.0ºC ; -199.9ºF,752.0ºF�

: L type (N ,Cr,Co / N ,Fe,Mn,Cu) Thermocouple , -150ºC,800ºC; -238ºF,1472ºF� �

: L type (N ,Cr,Co / N ,Fe,Mn,Cu) Thermocouple,-150.0ºC,800.0ºC;-199.9ºF,999.9ºF� �

: Cu-50 , -199ºC,200ºC ; -199ºF,392ºF

: Cu-50 , -199.0ºC,200.0ºC ; -199.0ºF,392.0ºF

: Pt-100 , -200ºC,650ºC ; -328ºF,1202ºF

: Pt-100 , -199.9ºC,650.0ºC ; -199.9ºF,999.9ºF

: Un t Select on. or can be chosen. (Default: ) Modbus Address: 40005� �

: Operat on Scale m n mum (Low L m t) value. It changes accord ng to the process� � � � � �

�nput type and scale. (Default: -199) Modbus Address: 40006

: Operat on Scale max mum (H gh L m t) value. It changes accord ng to the� � � � � �

process nput type and scale. (Default: 900) Modbus Address: 40007�

: Process Set value Low L m t. M n mum set value s def ned w th th s parameter.� � � � � � � �

It can be adjusted between Operat on Scale m n mum and max mum ( - ) � � � �

values. (Default: -199) Modbus Address: 40008

: Process Set value H gh L m t. Max mum set value s def ned w th th s parameter.� � � � � � � �

It can be adjusted between Operat on Scale m n mum and max mum ( - ) � � � �

values. (Default: 900) Modbus Address: 40009

: D splay offset for process value. It can be adjusted from -10% of scale to 10% of�

scale. It s added to the process d splay value. (Default: 0) Modbus Address: 40010� �

: Def ne f lter t me(sec) for d splayed value. (Default: 1.0) Modbus Address: 40011� � � �

Order ng Informat on� �

Eco PID+ ( 48x48 DIN 1/16 )

D mens on� �

48x48 DIN 1/16

4 .

S .

Outputs-1

1R 1 x Relay Output (5A@250V at Res st ve Load) (NO,C)V� �

2R 2 x Relay Output (5A@250V at Res st ve Load) (NO,NO,C)V� �

S SSR Dr ver Output (Max. 10mA, Max. 12V )�Z

Outputs-2D

Commun cat on� �

0 None

485 RS-485 Commun cat on� �

Termékspecifikációk

Márka:	Emko
Kategória:	hőmérséklet szabályozó
Modell:	ECO PID+

Szüksége van segítségre?

Ha segítségre van szüksége Emko ECO PID+, tegyen fel kérdést alább, és más felhasználók válaszolnak Önnek

Az Ön neve*

Az Ön e-mail címe*

Írja ide kérdését

Útmutatók hőmérséklet szabályozó Emko

Emko ESM-1520-N Útmutató

28 Augusztus 2024

Emko ECO PID+ Útmutató

28 Augusztus 2024

Emko Eco PID Útmutató

28 Augusztus 2024

Emko Eco Lite Útmutató

28 Augusztus 2024

Emko CHANNEL8A-N Útmutató

25 Augusztus 2024

Emko ESM-7720 Útmutató

25 Augusztus 2024

Emko ESM-3711-CN Útmutató

25 Augusztus 2024

Emko ESM-4410 Útmutató

25 Augusztus 2024

Emko ESM-4435 Útmutató

25 Augusztus 2024

Emko ESM-3720 Útmutató

17 Augusztus 2024

Útmutatók hőmérséklet szabályozó

Legújabb útmutatók hőmérséklet szabályozó

IFM LT8924 Útmutató

6 December 2024

IFM OW5020 Útmutató

5 December 2024

Jung TVA230NCWW Útmutató

2 Október 2024

Jung TRGO2 Útmutató

30 Szeptember 2024

Technoline WS 9245 Útmutató

28 Szeptember 2024

Voltcraft ETC-200 Útmutató

21 Szeptember 2024

Jung TRME2 Útmutató

20 Szeptember 2024

Jung TRCD241 Útmutató

19 Szeptember 2024

Dimplex AR99DC1 Útmutató

18 Szeptember 2024

Fluke 7102 Útmutató

15 Szeptember 2024