Használati útmutató WyreStorm MX-0404-HDBT-H2A-KIT

WyreStorm hi-fi rendszer MX-0404-HDBT-H2A-KIT

Olvassa el alább 📖 a magyar nyelvű használati útmutatót WyreStorm MX-0404-HDBT-H2A-KIT (4 oldal) a hi-fi rendszer kategóriában. Ezt az útmutatót 4 ember találta hasznosnak és 2 felhasználó értékelte átlagosan 4.5 csillagra

Letöltés PDF

Oldal 1/4

4x4 4K UHD HDBaseT (35m/115ft) Matrix with audio breakout,

HDCP 2.2 and PoH Receivers

MX-0404-HDBT-H2A-KIT Quickstart Guide

IMPORTANT! Installation Requirements

• Visit the product page to download the latest rmware, document

version, additional documentation, and conguration tools.

• Install the latest rmware (if available) to ensure that all features

described in this document are available during and after installation.

• Read through the Wiring and Connections section for important wiring

guidelines before creating or choosing premade cables.

In the Box

1 x MX-0404-HDBT-H2A-KIT HDBaseT Matrix Switcher

4 x HDBaseT PoC display receivers

1 x Handheld IR Remote (CR2025 Battery not Included)

4 x IR emitters

4 x IR Broadband Receiver (30KHz to 50KHz)

1 x IR Extension Cable

1x AC Power Cord with US Plug

1x AC Power Cord with UK Plug

1x AC Power Cord with EU Plug

2x Mounting Brackets and accessories (matrix)

1x Quickstart Guide (this document)

Basic Wiring Diagram

MX-0404-HDBT-H2A-KIT Quickstart Guide | 200205

UK: +44 (0) 1793 230 343 | ROW: 844.280.WYRE (9973)

support@wyrestorm.com

1 of 4

WyreStorm recommends reading through this document in its entirety to become familiar with the product’s features prior to starting the installation

process.

Wiring and Connections

WyreStorm recommends that all wiring for the installation is run and terminated prior to making connections to the switcher. Read through this section in this

entirety before running or terminating the wires to ensure proper operation and to avoid damaging equipment.

HDMI/HDBaseT Wiring

IMPORTANT! Wiring Guidelines

• The use of patch panels, wall plates, cable extenders, kinks in cables, and

electrical or environmental interference will have an adverse effect on HDMI

and Ethernet transmission limiting performance. Steps should be taken to

minimize or remove these factors completely during installation for best

results.

• WyreStorm recommends using high quality HDMI cables such as

WyreStorm Express to ensure the highest content performance available.

• The type of category cable and length used can restrict the available video

resolution. While Cat5e can be used, WyreStorm recommends using Cat6

or higher to ensure the highest content performance available. See Video

Resolutions in the Specications table before determining cable type and

length.

Pin 1

Pin 8

Wire colors shown follow EIA/TIA-568B standard.

Pin 1:

Pin 2:

Pin 3:

Pin 4:

Pin 5:

Pin 6:

Pin 7:

Pin 8:

White/Orange

Orange

White/Green

Blue

White/Blue

Green

White/Brown

Brown

IR TX/RX Wiring

IMPORTANT! IR TX/RX Guidelines

• WyreStorm IR ports function differently than standard IR ports. For this

reason only WyreStorm IR emitters and receivers can be used.

• WyreStorm IR emitter and receiver cables cannot be spliced as cutting

into the cables will short the shield. While an extension cable may be used,

WyreStorm assumes no responsibility for operation using an extension

cable.

• When connecting the IR TX to an IR connecting blocks or control system

with different plugs, a cable must be made following the IR TX Port Pinout

diagram.

• When connecting to an IR control system use the WyreStorm CAB-IR-LINK

cable. This cable compensates for differences between the WyreStorm RX

and the control systems TX connection. Visit the CAB-IR-LINK product page

for details.

IR TX Port Pinout

Tip: Anode

Sleeve: Cathode (IR Signal)

IR RX/Ext Port Pinout

Tip:

Ring: IR Signal

+5V DC

Sleeve: Ground (GND)

RS-232 Wiring

Most control systems and computers are DTE where pin 2 is RX, this can vary

from device to device. Refer to the documentation for the connected device for

pin functionally to ensure that the correct connections can be made. 5

9 8 7 6

4 13 2

Outside of DB9 chassis port shown.

Unidnetiﬁed pins have no function and should

not be connected.

Pin 3: RX (Receive)

Pin 2: TX (Transmit)

Pin 5: GND (Ground)

MX-0404-HDBT-H2A-KIT Quickstart Guide | 200205

UK: +44 (0) 1793 230 343 | ROW: 844.280.WYRE (9973)

support@wyrestorm.com

2 of 4

EDID Settings

EDIDs can be congured to resolve issues with video output on displays that may not accept the maximum resolution available from the source.

• When set to Smart EDID (default) the matrix will scan all selected displays for the lowest resolution.

• When EDID Copy or a direct EDID is being used, SmartEDID is turned Off.

• Ensure that a display is connected and powered On to the selected output before copying EDIDs or the copy will fail. When this occurs, EDID will be set to

4K@30Hz 2ch.

• Power to the matrix must be cycled (Off/On) after changing dip switches in order for the setting to take effect.

Accessing the Web UI

Note: This matrix is set to a default static IP Address (192.168.11.143). In

order to communicate with it initially the PC must be set to a 192.168.11.xxx

address. This can be changed back once a static IP is set within a different

range.

1. Connect the matrix to the same network as a PC.

2. Open a web browser and enter the IP Address of the matrix.

Default: 192.168.11.143 | Password: admin

Note: The installer password and general password are the same by default.

WyreStorm recommends changing the password for installer login to avoid

any unwanted changes being made to the matrix conguration.

Smart EDID –

Display Lowest

Resolution - 2ch

only (default)

Front Panel, Web UI

or API EDID Control

4K@30Hz 2ch with

HDR Support

4K@30Hz (8bit

only) 2ch with HDR

Support

4K@30Hz 5.1ch with

HDR Support

4K@30Hz 7.1ch with

HDR Support

4K @60Hz 2ch 1080p @60Hz 2.0ch

audio

Copying EDIDs

1. Set the EDID dipswitch to the Front Panel, Web UI or API EDID Control

(all switches up).

2. Reboot the matrix.

3. Using the front navigation buttons, select the input port for the output.

Example: Input 2 for Output 2

4. Once the output port indicator blinks, press and hold Enter for 5

seconds. OK indicates that the copy was successful, FL-2 indicates that

the copy failed.

5. Reboot the matrix

Note: EDID settings may also be congured using the Web UI. Refer to the

Accessing the Web UI section.

Troubleshooting

No or Poor Quality Picture (snow or noisy image)

• Verify that power is being supplied to all devices in the system and that they

are powered on.

• Verify that all source and HDBaseT connections are not loose and are

functioning properly.

• Verify that the HDBaseT cable is properly terminated per the HDMI/

HDBaseT Wiring section.

• Verify that the matrix, receiving device, and display support the output

resolution of the source.

• in theRefer to Video Resolutions Specications table for the max distance

based on resolution.

• If transmitting 3D or 4K, verify that the HDMI cables used are 3D or 4K rated.

No or Intermittent 3rd party Device Control

• Verify that the IR cable(s) is properly terminated.

See IR TX/RX Wiring.

• Verify that the IR emitter is located near the IR receiver on the device.

Troubleshooting Tips:

• WyreStorm recommends using a cable tester or connecting the cable to

other devices to verify functionality.

• Use a ashlight to locate the IR receiver behind any tinted panels on the

device being control

MX-0404-HDBT-H2A-KIT Quickstart Guide | 200205

UK: +44 (0) 1793 230 343 | ROW: 844.280.WYRE (9973)

support@wyrestorm.com

3 of 4

Termékspecifikációk

Márka:	WyreStorm
Kategória:	hi-fi rendszer
Modell:	MX-0404-HDBT-H2A-KIT

Szüksége van segítségre?

Ha segítségre van szüksége WyreStorm MX-0404-HDBT-H2A-KIT, tegyen fel kérdést alább, és más felhasználók válaszolnak Önnek

Az Ön neve*

Az Ön e-mail címe*

Írja ide kérdését

Útmutatók hi-fi rendszer WyreStorm

WyreStorm MX-0606-PP-POH Útmutató

25 Augusztus 2024

WyreStorm MX-0404-HDBT-H2A-KIT Útmutató

25 Augusztus 2024

WyreStorm SW-0501-HDBT Útmutató

25 Augusztus 2024

Útmutatók hi-fi rendszer

Legújabb útmutatók hi-fi rendszer

Klipsch ProMedia Ultra 2.0 Útmutató

6 Április 2025

Vaxis Atom 500 Útmutató

2 Április 2025

INKEE Benbox Útmutató

1 Április 2025

JL Audio SlamPak SLPK-CAN-SPYDER1 Útmutató

31 Március 2025

Teradek Bolt 10K Útmutató

29 Március 2025

Teradek Bolt 500 Útmutató

29 Március 2025

Teradek Cubelet 655 Útmutató

29 Március 2025

Teradek Cube Series Útmutató

29 Március 2025

Teradek Cube 725 Útmutató

29 Március 2025

Teradek Slice 676 Útmutató

29 Március 2025