Használati útmutató Winegard TRAV'LER SKA-733

Winegard TV antenna TRAV'LER SKA-733

Olvassa el alább 📖 a magyar nyelvű használati útmutatót Winegard TRAV'LER SKA-733 (4 oldal) a TV antenna kategóriában. Ezt az útmutatót 8 ember találta hasznosnak és 2 felhasználó értékelte átlagosan 4.5 csillagra

Letöltés PDF

Oldal 1/4

TRAV’LER®

Automatic Multi-Satellite TV Antenna

Model SKA-733 Reector & Bracket

INSTALLATION MANUAL

Made in the U.S.A.

Printed in U.S.A. © Winegard Company 2012 1/12 2452259

WINEGARD®

TRAV’LER® SHAW DIRECT Reector and Bracket Installation

Check to be sure that there is nothing above the TRAV’LER antenna that might

prevent it from raising. You will need at least 40” of clearance above the TRAV’LER

mount to ensure that you have room to install the reector. Pay attention to these Pinch

Points as the antenna raises.

Raise Antenna:

There are two ways to raise the antenna, automatic or manual; each is explained below.

A. Automatic:

Steps 1-7 explain how to use the TRAV’LER Interface Box to raise the mount.

1. Press and hold for 2 seconds to turn “ON” the TRAV’LER Interface Box. Wait until the [POWER]

 InterfaceBoxnishes“connectingtoantenna”.

* The TRAV’LER may enter the “Search Routine” after 10 seconds; this is normal (See NOTE Below).

2. Press [ENTER] and hold for 2 seconds or until the unit displays “Enter User Menu”. Press [SELECT] to

move the asterisk to “Yes”. Press [ENTER].

3. Press to move the asterisk to INSTALLATION.[SELECT]

4. Press You will be asked to provide a code to enter the Installation Menu.[ENTER].

5. Press 4 times to enter code 0000. [ENTER]

6. Press to move the asterisk to RAISE ANTENNA. Press Press to move [SELECT] [ENTER]. [SELECT]

the asterisk to Yes.

7. Press The TRAV’LER mount will raise up about half way. [ENTER].

* NOTE: If the TRAV’LER enters the “Search Routine,” and the TRAV’LER mount raises more than 1/2 way be-

fore RAISE ANTENNA is selected (See Step 6), the TRAV’LER will hit its Upper Hard Stop and “Motor Stall” will

appear. This is Normal.

The “Motor Stall” means the TRAV’LER is all the way up and the mount cannot raise any more. There are two

easy ways to clear the “Motor Stall”.

a. Press [ENTER] the TRAV’LER antenna will return to the “Installation Menu”

b. Press [POWER] the TRAV’LER antenna will stow and turn “OFF” (Restart at Step 1).

FIGURE 1

NOTE: Pinch Points are called out both for your safety and to protect the cables. Ca-

bles will be damaged if installed incorrectly. See pages 3-4 in this installation manual.

Rev. 4/09

Be Careful not to strip out the hole for the 5/16 inch

screws when you replace the clamp holding the

coax cables to the arm. DO NOT use a power tool.

8. With the Bracket mounted securely, connect the four Coax Cables to the Mount, as shown in Figure 6.

9. Find the Cable Tie on the coax cables

that you have just connected to the mount. Place the

coax cable clamp on the cables just below this cable

tie. Carefully screw this clamp to the front of the Lift Arm

using the 5/16 inch screw provided. See Figure 5.

DO NOT over tighten this screw.

NOTE: If the cable tie is missing, install the clamp 14” from

the end of the connectors.

Calibrate the Elevation Motor:

1. Press and hold for 2 seconds to turn “ON” the TRAV’LER Interface Box. Wait until the [POWER]

 InterfaceBoxnishes“connectingtoantenna”.

2. Press and hold for 2 seconds or until the unit displays “Enter User Menu”. Press [ENTER]

to move the asterisk to “Yes”. Press . [SELECT] [ENTER]

3. Press to move the asterisk to INSTALLATION.[SELECT]

4. Press . You will be asked to provide a code to enter the Installation Menu. [ENTER]

5. Press 4 times to enter code 0000.[ENTER]

6. From the Installation Menu,

7. Press to move “ * ” to “Calibrate EL” and Press . [SELECT] [ENTER]

8. Press to move “ * ” to YES.[SELECT]

9. Press to start the elevation calibration procedure. The LCD should now display [ENTER]

“ Calibrate EL In Progress ...”.

10. After a few moments the IDU LCD will display

“On EL Hard Stop?

Yes *No”.

Visually examine the antenna to verify that the antenna is against the Hard Stop. The antenna will be pointing as

far up as it can go, this is the Hard Stop.

11. Press once to move asterisk to “Yes” if antenna is on the Hard Stop.[SELECT]

12. Press and the LCD will display “Calibrate EL Success”.[ENTER]

13. Press and Hold for 2 seconds to to stow the antenna.[POWER]

FIGURE 6

Coax

Connections

Termékspecifikációk

Márka:	Winegard
Kategória:	TV antenna
Modell:	TRAV'LER SKA-733

Szüksége van segítségre?

Ha segítségre van szüksége Winegard TRAV'LER SKA-733, tegyen fel kérdést alább, és más felhasználók válaszolnak Önnek

Az Ön neve*

Az Ön e-mail címe*

Írja ide kérdését

Útmutatók TV antenna Winegard

Winegard Playmaker Útmutató

25 Augusztus 2024

Winegard TRAV'LER SK-7002 Útmutató

25 Augusztus 2024

Winegard Sensar III GS-2200 Útmutató

25 Augusztus 2024

Winegard FL5500A Útmutató

25 Augusztus 2024

Winegard TRAV'LER SKA-733 Útmutató

25 Augusztus 2024

Winegard SK-3005 Útmutató

25 Augusztus 2024

Winegard SquareShooter SS-2000 Útmutató

25 Augusztus 2024

Winegard SquareShooter SS-1000 Útmutató

25 Augusztus 2024

Winegard HD7084 Útmutató

25 Augusztus 2024

Winegard Carryout G2+ Útmutató

25 Augusztus 2024

Útmutatók TV antenna

Legújabb útmutatók TV antenna

Meliconi AT49 R1 USB Útmutató

30 Március 2025

Metronic 415047 Útmutató

28 Március 2025

Metronic 427017 Útmutató

28 Március 2025

Metronic 425031 Útmutató

27 Március 2025

Metronic 415054 Útmutató

27 Március 2025

Metronic 416975 Útmutató

27 Március 2025

Astrell AST808 Útmutató

26 Március 2025

Magnavox MC372 Útmutató

8 Január 2025

Magnavox MC347 Útmutató

8 Január 2025

Magnavox MG-ANT-104 Útmutató

8 Január 2025