Használati útmutató US Blaster USB 1392

US Blaster autórádió USB 1392

Olvassa el alább 📖 a magyar nyelvű használati útmutatót US Blaster USB 1392 (48 oldal) a autórádió kategóriában. Ezt az útmutatót 5 ember találta hasznosnak és 2 felhasználó értékelte átlagosan 4.5 csillagra

Letöltés PDF
Oldal 1/48
OWNERS MANUAL
CLASS-AB POWER AMPLIFIER
USB 1389 - 1390 - 1391 - 1392
USB 1389 - 1390 - 1391 - 1392
Class-AB Power amplifiers
GENERAL SAFETY INSTRUCTIONS
- Always read the user guide before using the equipment.
- Keep the user guide in a place where everyone can read it.
- Use the equipment indoors and not in humid environments.
- Never remove or insert a plug from or into a wall socket with wet hands.
- If the plug and/or cable and/or cable input of the equipment is damaged it must be repaired by
aprofessional.
- Always take the plug out of the wall socket in the event of a thunderstorm, and also when the
equipment is not being used for a while.
-Never remove the plug from the power socket by pulling on its cable.
- Install the equipment in such a way that sufficient cooling is possible.
- Never use the appliance in the vicinity of heat sources and/or in direct sunlight.
-Make sure that no small objects or liquids can get in to the appliance.
-Only clean the appliance with a slightly moist dust-free cloth. Do not use cleaning products or
solutions!
-The appliance contains no components, other than those mentioned in the user guide that can
be repaired or replaced by the user.
- If the appliance is defective, it must be repaired by a US Blaster qualified repairs company.
- Keep the equipment out of the reach of children.
Keep the packaging safe so that, if the equipment is defective, you can
send it back in its original packaging and so avoid any damage.
©US Blaster Europe BV
Do not carry out any repairs on the equipment yourself; doing so will invalidate the guarantee.
The equipment may also not be modified; doing so will also invalidate the guarantee.
The guarantee is also invalidated if accidents and damage of any form are caused as a result
of improper use and/or not heeding the warnings in general as laid out in this user guide.
US Blaster Europe accepts no responsibility for any personal accidents as a consequence of not
following the safety instructions and warnings. This is also the case for consequential loss in
any form.
USB 1389 - 1390 - 1391 - 1392
Class-AB Power amplifiers
INTRODUCTION
Thank you for purchasing this US BLASTER Class AB full range amplifier for your car audio system.
Now you own an amplifier of uncompromising design and engineering incorporating the latest advan-
ced circuit technology.
You will soon discover the amplifiers’ optimum sound and reliable performance.
US BLASTER amplifiers are adopted by advanced craftsmanship using the highest quality components
and strict quality control system. In order to provide you with long and pleasureable listening, we
recommend that you have your amplifier installed by an authorized US BLASTER dealer. It will ensu-
re installing your product properly and will also increase the warranty to one year. (please see the
warranty section for more details.)
Please read this manual thoroughly to ensure you get the maximum benefit from this amplifier. When
installed properly, this unit will provide you years of trouble-free performance.
DESIGN FEATURES
SMD Hi-Fi audio components.
FR-4 heavy duty double side PCB.
Low ESR high capacitance filter capacitor.
Super noise rejection circuit.
Smart protection system against overload, short circuit, overheat and low voltage.
Gold plated heavyduty connectors.
Intergrated high performance filters.
AMPLIFIER FUNCTIONS
1. Speaker connection
• Never connect the speaker cables with the chassis ground. This could destory your amplifier.
• Check that your speakers are connected correctly which means plus to plus and minus to minus.
We recommend speaker cable from 16 Gauge or up. Other connection ways are shown in the attach-
ment.
2. BATT+
Battery +(plus) terminal. The +(plus) 12 Volt power cable must be connected with a fuse on the bat-
tery +(plus) terminal. We recommenda fuse listed on pre-installation a 12 feet copper cable with 8
Gauge thickness or up.
3. REM
Remote terminal. The remote cable must be connected with the radio remote output
terminal so that the amplifier will switch on and off automatically with the radio. If there are two or
more amplifiers connected to this antenna terminal it might be necessary to add an additional relay.
Please consult your dealer.
4. GND
Chassis ground terminal. The chassis ground cable must be connected very tight on a nearbymassi-
veand electric conductiveplace.
©US Blaster Europe BV

Termékspecifikációk

Márka: US Blaster
Kategória: autórádió
Modell: USB 1392

Szüksége van segítségre?

Ha segítségre van szüksége US Blaster USB 1392, tegyen fel kérdést alább, és más felhasználók válaszolnak Önnek


Útmutatók autórádió US Blaster

US Blaster

US Blaster usb 1389 Útmutató

21 Augusztus 2024
US Blaster

US Blaster USB 1392 Útmutató

21 Augusztus 2024

Útmutatók autórádió

Legújabb útmutatók autórádió

Boss

Boss MR63UAB Útmutató

12 December 2024
Kenwood

Kenwood KDC-130UG Útmutató

9 December 2024
Alpine

Alpine MRP-M850 Útmutató

8 December 2024
Alpine

Alpine CTA-1505R Útmutató

8 December 2024
Audio-Technica

Audio-Technica AT-RX80 Útmutató

7 December 2024
Pioneer

Pioneer AVH-A240DAB Útmutató

7 December 2024
Pyle

Pyle PLMR14BW Útmutató

6 December 2024
Pyle

Pyle PLMR2DNBK Útmutató

6 December 2024
Pyle

Pyle PLTS73FX Útmutató

6 December 2024
Pyle

Pyle UPLMR15BW Útmutató

6 December 2024