Használati útmutató Traxxas EZ-Peak Dual

Traxxas Akkumulátor töltő EZ-Peak Dual

Olvassa el alább 📖 a magyar nyelvű használati útmutatót Traxxas EZ-Peak Dual (4 oldal) a Akkumulátor töltő kategóriában. Ezt az útmutatót 13 ember találta hasznosnak és 2 felhasználó értékelte átlagosan 4.5 csillagra

Letöltés PDF
Oldal 1/4
NiMH/LiPO DUAL CHARGER INST RUCT IONS
Covers Part #2972X
Thank you for purchasing the Traxxas EZ-Peak Dual charger.
This charger features exclusive Traxxas innovations that make
charging batteries easier and safer than ever. If you have any
questions or concerns about your charger, please contact our
customer support team for fast, friendly answers and solutions.
Contact information is at the bottom of this page.
WARNING! For best charging results and your safety, it is essential that you read and
understand these instructions, warnings, and precautions before using the charger.
Charging and discharging batteries has the potential for serious injury and damage
to property. Use care when charging and follow all instructions and cautions. A
B
C
D
EF
H
Charge
Status
iD LogoBattery Type
Traxxas High-Current
Connector
Charge
Progress
Charge Rate
(Amps)
A
B
C
D
EF
G G
H
*Note: Either charger output port can be used independently or both ports can be used
simultaneously to charge. Use the buttons corresponding with the chosen port(s) to
operate the charger.
1. Plug the charger into an AC wall outlet
and connect the battery/batteries
2. Verify the charge settings
Charging Traxxas iD NiMH Batteries
Battery type selected must match the battery type shown on the battery.
The charger will recognize the iD batteries
and show you the charge settings.
Charge Rate StartBattery Type
HKC18031-R02 180808
T R A X X A S . c o m
Traxxas, 6250 Traxxas Way, McKinney, TX 75070,
Phone: 1-888-TRAXXAS (Toll-free, US only) or 972-549-3000, Fax: 972-549-3011, e-mail: support@Traxxas.com
3. Charging
Press and hold the Start button(s)
for 1 second. The charger will
play a tone, indicating that
charging has started. Press once
to stop. The charger will play a
tone, indicating that charging
has been canceled. The charge
progress LEDs will light as the
battery charges.
Charging
(flashing)
Charge Cycle Progress
4. Charge cycle complete
The charger will play a complete tone, followed by one or two beeps
to indicate channel 1 (left) or channel 2 (right) charging is complete.
The EZ Peak Dual will
trickle charge your NiMH
battery at up to 200mA
for 12 hours after the
charge cycle is complete.
Cycle
Complete
(solid)
A. Start/Stop
B. LiPo Charge Mode Select
C. Battery Type Select
D. Charge Rate Select
E. Charger Output Ports (Traxxas
High-Current Connector)*
F. 2S/3S Lipo Balance Ports
(pull to remove cover)
G. Charge Status LEDs
H. Charge Progress/
Charge Rate LEDs
Identifying iD Batteries LiPo battery shown, NiMH battery similar
Dual Charge Mode
Charging Traxxas iD LiPo Batteries
Fast charge
Fast charges batteries without
balancing your cells. Stops charging
when the first cell reaches peak voltage.
Depending on the condition of the
batteries, this may reduce the charge
time by a few minutes.
Balance charge
Always balance charge your LiPo
batteries for maximum capacity,
voltage, and battery life. This is the
default setting for Traxxas iD batteries.
The EZ-Peak Dual performs a balance
charge quickly and efficiently.
LiPo Charging M
Storage charge
Makes it easy to charge or discharge
batteries to the proper storage
voltage. Use this mode whenever
batteries will be stored unused for
more than 7 days.
Change your LiPo charging mode if desired.
The default setting for iD LiPo batteries is Balance Charge.
Charging Traxxas iD Batteries
in High Output Mode
High Output Mode allows you to charge high capacity batteries
at a faster charge rate. Use the high output channel to charge your
5000 mAh NiMH batteries at 5 amps and your 4000 mAh and larger
LiPo batteries at a “2C” charge rate (2C is 2 times the capacity; 4000
mAh x 2 = 8000 or 8 amps). Only one Traxxas battery at a time can be
charged in High Output Mode using the output port on the right side
of the charger (the left side of the charger is disabled).
Move the switch
to High Output, and follow steps 1-4 for Traxxas iD battery charging.
Note: The 5A LED will light to indicate the charge rate setting for Traxxas
Power Cell batteries requiring a charge current of 5 amps or less.
4. Charge cycle complete
The charger will play a complete tone, followed by one or two beeps to
indicate channel 1 (left) or channel 2 (right) charging is complete.
1. Plug the charger into an AC wall outlet
and connect the battery/batteries
The charger will recognize the iD batteries
and show you the charge settings.
2. Verify the charge settings
Battery type selected must match the battery type shown on the battery.
3. Charging
Press and hold the Start button(s) for 1 second. The charger will play a
tone, indicating that charging has started. Press once to stop. The charger
will play a tone, indicating that charging has been canceled. The charge
progress LEDs will light as the battery charges.
Charging
(flashing)
Charge Cycle Progress
Cycle
Complete
(solid)
Disabled
Start
Charge Mode
(the default is
Balance) Charge RateBattery Type
Dual Charge Mode
1. Connect the main connector and the balance connector to the charger
(pull to remove balance port cover)
2. Enter Advanced Mode:
Simultaneously press and hold
the Start button and the Charge
Rate Select button for 2 seconds.
The charger will play a short tone.
Charging Traxxas Batteries without iD in Advanced Mode
Advanced Mode offers full manual control for users that have an in-depth knowledge of battery types (chemistry) and battery charging techniques.
Advanced mode also allows you to adjust the charge rate (current) for Traxxas iD batteries. If you do not understand the differences in various battery
types or what charge rates should be used, then do not use Advanced Mode. Use the Traxxas Battery iD System instead for safe, easy, and fast charging.
High Output Mode Advanced Mode (see above) can also be used while charging batteries in .
When batteries are connected for charging
that do not have Traxxas Battery iD, the red
charge rate/progress LEDs will sweep in a
scanning motion. Advanced Mode must be
used for manual battery type and charge rate
selection. The Start button will not light blue
when there is no Traxxas Battery iD present.
WARNING: DO NOT attempt to charge LiPo batteries with missing or damaged balance connectors. The EZ-Peak Dual will default to LiPo mode
charging when a balance plug connection is detected. If you fail to plug in the balance connector, or attempt to charge a LiPo battery with a damaged
or missing balance connector, you create the risk of accidentally selecting to charge a LiPo battery in NiMH mode, resulting in fire and possible injury
to yourself and others. Always make sure to select the battery type that matches the connected battery. If you do not understand what this warning
means, do not attempt to use Advanced Mode on the EZ-Peak Dual. Contact Traxxas for more information.
LiPo Only
WARNING: When the charger is switched to High Output Mode, the charge rate selection begins at 5 amps and goes up to 8 amps. Make sure you
do not exceed the maximum charge rate recommended by your battery manufacturer. If you are unsure about the maximum charge rate for your
battery, then do not attempt to charge the battery in Advanced Mode. Contact Traxxas or your local hobby dealer for more information.
3b. Charging a LiPo battery or batteries
LiPo mode should be selected by default (green LEDs). If the LiPo and
NiMH LEDs alternately blink, then the balance connector is either
disconnected or damaged. Do not attempt to charge this LiPo battery.
LiPo Only
3a. Charging a NiMH battery or batteries
Press and hold the Start button(s) for 1 second. The charger will play
a tone, indicating that charging has started. Press once to stop. The
charger will play a tone, indicating that charging has been canceled.
The charge progress LEDs will light as the battery charges.
Charge cycle progresses as shown in steps 3 and 4 for iD
NiMH charging.
Select NiMH
Battery Type (Red)
Select Charge
Rate
Select Charge
Rate
Press and hold the Start button(s) for 1 second. The charger will play a
tone, indicating that charging has started. Press once to stop. The charger
will play a tone, indicating that charging has been canceled. The charge
progress LEDs will light as the battery charges.
Charge cycle progresses as shown in steps 3 and 4 for iD LiPo charging.
Select Charge
Mode

Termékspecifikációk

Márka: Traxxas
Kategória: Akkumulátor töltő
Modell: EZ-Peak Dual

Szüksége van segítségre?

Ha segítségre van szüksége Traxxas EZ-Peak Dual, tegyen fel kérdést alább, és más felhasználók válaszolnak Önnek


Útmutatók Akkumulátor töltő Traxxas

Traxxas

Traxxas EZ-Peak Dual Útmutató

2 Szeptember 2024
Traxxas

Traxxas EZ-Peak Live Dual Útmutató

30 Július 2024
Traxxas

Traxxas EZ-Peak Live Útmutató

25 Július 2024
Traxxas

Traxxas EZ-Peak Plus Útmutató

4 Július 2024

Útmutatók Akkumulátor töltő

Legújabb útmutatók Akkumulátor töltő

Schwaiger

Schwaiger LAD230 531 Útmutató

9 Április 2025
Schwaiger

Schwaiger 658699 Útmutató

9 Április 2025
Schwaiger

Schwaiger LAD440 532 Útmutató

9 Április 2025
Ergotron

Ergotron 97-939 Útmutató

3 Április 2025
Ergotron

Ergotron YES35 Útmutató

3 Április 2025
Trust

Trust Maxo 25242 Útmutató

3 Április 2025
Ergotron

Ergotron LiFeKinnex Útmutató

3 Április 2025
Voltcraft

Voltcraft PB-19C Útmutató

31 Március 2025
Watson

Watson 9V-2BC Útmutató

30 Március 2025
ISDT

ISDT Q6 Lite Útmutató

26 Március 2025