Használati útmutató SEADA G44-HDMI
Olvassa el alább 📖 a magyar nyelvű használati útmutatót SEADA G44-HDMI (1 oldal) a Processor kategóriában. Ezt az útmutatót 2 ember találta hasznosnak és 2 felhasználó értékelte átlagosan 4.5 csillagra
Oldal 1/1
SD- - 2 EN 01 1V0
G44-HDMI Quick Start Manual
Note
1. Do not fix the device to any surface which is a heat source to avoid over heating
2. Do not cover the surface or ventilation grills of the device to avoid over heating
1. Verify the package contents
Please verify the package contents against the List Below
1. G44-HDMI Controller
x1
5. Network Cable
x1
2. Power Cable
x1
6. Remote Control
x1
3. Quick Start Manual
x1
7. 5-pin Phoenix Connector
x4
4. Ground Wire
x1
8. 3-pin Phoenix Connector
X4
2. Set up the G44-HDMI
I. Connect the power cable to the unit and power it up
II. Connect the outputs to the screens of the video wall
III. Connect all the video sources to the inputs of the devices
Note: G44H remembers the settings used on the device before powering off. The default setting for the new
unit is video wall with across the 4 screens. All outputs are set at resolution of 1920 x 1080@60. 2x2 input 1
3. Run the software on control PC
Users can run the G H.exe software directly without installation. Software can be download from the 44 ed
SEADA website ( ). Double click the G H software to get started. https://seada.co.uk/downloads 44
4. Connect through Serial Port
Connect the G -H with a serial cable to the control PC (cable not included in the package) 44 DMI
If the software was connected via UART (RS232) last time,
software will connect to the G -H automatically via 44 DMI
RS232. If it was used at Network last time, a ‘Network
Timeout’ error message will be shown on screen and users need to set up as below for RS232 connection in
the software
• Choose ‘ ’ instead of ‘UART Network’
• Select the from th dropdown menu COM port e Port
• Press button to connect ‘Disconnected’
5. Connect through Network
The default IP address for G -HDMI controller is Users need to change the IP address of the 44 192.168.0.247,
control PC to IP address and the same network segment as the G -H in static 44 DMI at TCP/IPv4 Ethernet
Properties
IP address: any address between and except the address which has been taken 192.168.0.2 192.168.0.254
by the G -H 44 DMI
Subnet mask: Default Gateway: 255.255.255.0, 192.168.0.1
Connect the G44-H with a CAT cable to the control PC (cable included in the package) DMI
Termékspecifikációk
Márka: | SEADA |
Kategória: | Processor |
Modell: | G44-HDMI |
Szüksége van segítségre?
Ha segítségre van szüksége SEADA G44-HDMI, tegyen fel kérdést alább, és más felhasználók válaszolnak Önnek
Útmutatók Processor SEADA
30 Augusztus 2024
30 Augusztus 2024
30 Augusztus 2024
30 Augusztus 2024
30 Augusztus 2024
30 Augusztus 2024
30 Augusztus 2024
30 Augusztus 2024
30 Augusztus 2024
30 Augusztus 2024
Útmutatók Processor
- Processor Phoenix Gold
- Processor Fujitsu
- Processor HP
- Processor Allen & Heath
- Processor Asus
- Processor Arturia
- Processor Zoom
- Processor Bose
- Processor Alpine
- Processor SPL
- Processor Smart-AVI
- Processor Black & Decker
- Processor Bogen
- Processor TC Helicon
- Processor LD Systems
- Processor Datapath
- Processor Pyle
- Processor MuxLab
- Processor DataVideo
- Processor Dangerous Music
- Processor Atlas Sound
- Processor Ashly
- Processor Neutrik
- Processor Siig
- Processor Gefen
- Processor Avenview
- Processor DBX
- Processor Lectrosonics
- Processor Vivolink
- Processor BSS Audio
- Processor KanexPro
- Processor Rupert Neve Designs
- Processor BZBGear
- Processor Matrox
- Processor Intel
- Processor Eventide
- Processor Radial Engineering
- Processor Solid State Logic
- Processor Drawmer
- Processor Sonifex
- Processor Manley
- Processor Helix
- Processor Christie
- Processor AudioThing
- Processor Heritage Audio
- Processor FabFilter
- Processor Metric Halo
- Processor Henry Engineering
- Processor MyMix
Legújabb útmutatók Processor
2 Október 2024
21 Szeptember 2024
12 Szeptember 2024
6 Szeptember 2024
4 Szeptember 2024
4 Szeptember 2024
4 Szeptember 2024
4 Szeptember 2024
4 Szeptember 2024
4 Szeptember 2024