Használati útmutató Ruckus Wireless ZoneFlex R710

Ruckus Wireless hozzáférési pont ZoneFlex R710

Olvassa el alább 📖 a magyar nyelvű használati útmutatót Ruckus Wireless ZoneFlex R710 (4 oldal) a hozzáférési pont kategóriában. Ezt az útmutatót 4 ember találta hasznosnak és 2 felhasználó értékelte átlagosan 4.5 csillagra

Letöltés PDF

Oldal 1/4

Published August 2016, Part Number 800-70938-001 Rev E

Page 1 of 4

T710 Access Point

Quick Setup Guide

This Mounting Guide provides step-by-step instructions on how to

field-install the Ruckus Wireless T710 access point (AP).

For detailed information on planning the installation, performing a site

survey, and operating the T710, refer to the ZoneFlex Outdoor Access

Point User Guide, available at https://support.ruckuswireless.com.

WARNING: Only trained and qualified personnel should be allowed to

install, replace, or service this equipment.

WARNING: Installation of this equipment must comply with local and

national electrical codes.

CAUTION: Make sure that you form a 80mm - 130mm (3”-5”) drip

loop in any cable that is attached to the AP or the building. This will

prevent water from running along the cable and entering the AP or the

building where the cable terminates.

CAUTION: Be sure that grounding is available and that it meets local

and national electrical codes. For additional lightning protection, use

lightning rods and lightning arrestors.

CAUTION: Make sure that proper lightning surge protection

precautions are taken according to local electrical code.

WARNING: Ruckus Wireless strongly recommends that you wear eye

protection before mounting the T710.

T HIS GUIDE IN OTHER LANGUAGES

请从以下网站获得该指南的简体中文版

https://support.ruckuswireless.com.

Vous trouverez la version française de ce guide à l'adresse suivante

https://support.ruckuswireless.com.

このガイドの⽇本語版は https://support.ruckuswireless.com

でご覧ください。

이 가이드의 한국어 웹 버전은 사이트

(https://support.ruckuswireless.com) .에서 확인하시기 바랍니다

Veja a versão em português (Brasil) deste guia em

https://support.ruckuswireless.com.

Puede ver la versión en español (América Latina) de esta guía en

https://support.ruckuswireless.com.

BEFORE YOU BEGIN

Before deploying your Ruckus Wireless T710, verify that all items listed

in Package Contents are included in the package. If any item is

damaged or missing, notify your authorized Ruckus Wireless sales

representative. Also, make sure that you have the required hardware

and tools.

REQUIRED HARDWARE AND TOOLS

• Customer-supplied outdoor-rated three-wire (1-2mm2 or 14-

18AWG) AC cable

• 1/2” (13mm) flat-blade screwdriver or equivalent

• No. 2 Phillips screwdriver

• Small flat-blade screwdriver

• Torque wrench or torque screwdriver with sockets

• Long-nose pliers

• Electrical wire stripping and terminal crimping pliers

• Pipe or pole --OR-- a sturdy flat surface

• Electric drill with drill bits and customer-supplied wall anchors, flat

washers, and hex nuts for flat-surface mount

• Four factory-supplied 1/2” (12.7mm) wide stainless steel

adjustable clamps, 2.5” (63.5mm) diameter, for main mounting

bracket on smaller poles

• Ruler

PACKAGE CONTENTS

A complete T710 field installation package includes all of the items

listed below (see Figure 1for illustrations):

• T710 Access Point (A)

• M25 data cable gland extender (B)

• Three M25 data cable glands (C)

• Outdoor AP Mounting Bracket (D), consists of:

• Mounting bracket

• U-joint bracket

• Linkage bracket

• AP bracket

• AC Power Cable End Connector (E)

• Cable Gland Extender Flat Gasket (F)

• Safety cable kit (G)

• One ground wire with lug (H)

• Service Level Agreement/Limited Warranty Statement

• Regulatory Statement

• Ruckus Wireless AP Getting Started Guide

• Declaration of Conformity

• This Quick Setup Guide

Figure 1: Package Contents

S TEP 1: CONNECTING AND SEALING THE RJ-45

CABLES

The T710 may use zero, or one or two RJ-45 cables, one for Ethernet

when configured as a Root AP (RAP), and another when the T710 is

supplying PoE out to a peripheral device, such as a small cell or micro

cell radio. When the T710 uses RJ-45 cables, connect and seal the

cables using the M25 data cable glands as shown in Figure 3.

WARNING: Do not use any PoE injector not tested and approved by

Ruckus Wireless to power the T710 Access Point.

WARNING: Do not plug PoE IN power into the PoE OUT port. See

Figure 2.

WARNING: If using PoE OUT, it is MANDATORY to use the custom

Ruckus supplied 60W PoE injector (part #902-0180-XX00), or to use

AC power.

WARNING: If using a PoE switch to supply power to the T710, 30W

MUST be reserved for the T710 on the switch. Failure to ensure a

30W supply may result in unpredictable operation of the access point.

Additionally, if using a PoE switch, the T710’s PoE OUT port cannot be

used to power additional devices.

Figure 2: PoE IN and PoE OUT ports

1Feed the end of the cable through the sealing nut, rubber O-ring,

clamping ring assembly and cable gland base as shown in Figure

CAUTION! The minimum software revision for the T710

is ZoneFlex (ZF) 9.13 or later, or SmartZone (SZ) 3.4 or

later.

DO NOT CONNECT THE T710 TO A RUCKUS

WIRELESS ZONEDIRECTOR RUNNING 9.12.2 OR

EARLIER.

Published August 2016, Part Number 800-70938-001 Rev E

Page 2 of 4

Figure 3: RJ-45 cable and cable gland assembly

2Use a wide flat-blade screwdriver to remove the required (RESET/

PoE OUT or PoE IN) blanking cap from the T710.

3Connect the cable to the Ethernet port in the T710.

4Tighten the cable gland base into the T710 chassis to 7 N.m or

62 in-lbs.

5Wrap the clamping ring assembly around the rubber O-ring. Make

sure that the clamping ring assembly fully encloses the rubber O-

ring.

6Seat the clamping ring assembly and rubber O-ring in the cable

gland base.

7Hand-tighten the sealing nut.

S TEP 1A: CONNECTING THE SFP OPTIC MODULE TO

THE FIBER PORT

To connect to fiber backhaul, plug an SFP Optic module into the Fiber

port. The SFP module is hot-swappable and can be removed with

fingers or simple tools.

NOTE: Recommended modules specified to work with this system

are: Finisar GPON FTGN2117P2TUN, Finisar EPON

FTEN2217P1CUN-BC, Finisar 1000BaseLX FTLF1318P3BTL, Xavi

XO-3901 GPON ONT.

NOTE: The fiber cable must be a single diameter cable, not a zipcord.

Figure 4: SFP module cable gland assembly

S TEP 2: ATTACHING THE U-JOINT BRACKET TO THE

MOUNTING BRACKET

1Position the U-joint bracket on the mounting bracket.

NOTE: Mount the U-joint bracket in any direction on the mounting

bracket, preferably to allow AP azimuth adjustments. Then the AP

bracket allows AP elevation adjustments.

Figure 5: U-joint bracket attached horizontally to the mounting bracket

2Use four 1/4-28 bolt and washer sets (A) to mount the U-joint

bracket (B) to the mounting bracket (C). Tighten the bolts to 9.5

N.m (7 ft-lbs).

3Continue with Step 3a: Attaching the Mounting Bracket to a

Flat Surface or Step 3b: Attaching the Mounting Bracket to a

Metal Pole.

S TEP 3A: ATTACHING THE TO MOUNTING BRACKET A

FLAT SURFACE

1Place the mounting bracket at the location on the flat surface

where you want to mount the AP. Use the holes on the mounting

bracket as a template to mark the locations of the mounting

holes.

Figure 6: Mounting bracket flat surface holes

2Remove the mounting bracket from the flat surface.

3Drill holes required for the mounting hardware.

NOTE: The hardware required for mounting to a wall are not included

in the mounting kit.

4Attach the mounting bracket to the flat surface using the

mounting hardware.

5Using the mounting hardware instructions, tighten the hardware to

secure the mounting bracket.

6Continue with Step 4: Mounting the Linkage Bracket to the U-

Joint Bracket.

S TEP 3B: ATTACHING THE MOUNTING BRACKET TO A

METAL POLE

1Insert the open end of one steel clamp into the upper two slots on

the mounting bracket.

2Take the other steel clamp and insert it into the lower two slots on

the mounting bracket.

NOTE: The clamps can be daisy-chained together to

accommodate larger poles.

3Use the clamps to attach the mounting bracket to the pole.

Tighten the clamps to 3 N.m or 27 in-lbs, or per manufacturer’s

specifications.

Figure 7: Attaching the mounting bracket to a vertical pole

4Continue with Step 4: Mounting the Linkage Bracket to the U-

Joint Bracket.

S TEP 4: MOUNTING THE L BINKAGE RACKET TO THE

U-JOINT BRACKET

The linkage bracket attaches to the U-joint bracket using an M8 bolt

and washer set. The linkage bracket is symmetrical, and either end

can be attached to the U-joint bracket.

NOTE: Make sure that linkage bracket is installed with its serrated

external-tooth lock washer on the inside of the U-joint bracket

flanges. This ensures that the azimuth adjustment does not

change.

1Loosely assemble the linkage bracket (A), the U-joint bracket (C),

one serrated external-tooth lock washer (B), and one M8 bolt

and washer set (D).

Figure 8: Attaching the linkage bracket to the U-joint bracket

Cable gland base

Clamping ring assembly

Rubber O-ring

Sealing nut

Published August 2016, Part Number 800-70938-001 Rev E

Page 3 of 4

2Set the azimuth required by the AP.

3Tighten the M8 bolt to 13.6 N-m (10 ft-lbs).

4Continue with Step 5: Attach the AP bracket to the linkage

bracket.

S TEP 5: ATTACH THE AP BRACKET TO THE LINKAGE

BRACKET

Attach the AP bracket to the linkage bracket using the included bolt,

nut, lock washer, flat washer, serrated external-tooth washer shown in

Figure 9.

The AP bracket attaches to the linkage bracket using an M8 bolt and

washer set. The linkage bracket is symmetrical, and either end can be

attached to the AP bracket.

NOTE: Make sure that linkage bracket is installed with its serrated

external-tooth lock washer on the inside of the AP bracket flanges.

This ensures that the elevation adjustment does not change.

1As described in Step 4: Mounting the Linkage Bracket to the

U-Joint Bracket, loosely assemble the AP bracket (shown in

Figure 10), the linkage bracket (A in Figure 8), the second

serrated external-tooth lock washer (B in Figure 8), and the

second M8 bolt and washer set (D in Figure 8).

Figure 9: Attach the linkage bracket to the AP bracket

S TEP 6: ATTACHING THE AP BRACKET TO THE

ACCESS POINT

1Place the AP bracket onto the back side of the AP so that the four

larger screw holes on the bracket align with the four screw holes

on the AP. Make sure that the end of the AP bracket with the

hoisting loop is on the same side as the AP PoE IN port.

Figure 10: Attaching the AP bracket to the AP

2Use four 0.5-inch x 0.250-28 hex bolts with split lock and flat

washer sets to mount the AP bracket to the AP. Tighten the bolts

to 2.5-3.0 N.m or 22-27 in-lbs.

CAUTION: Make sure that the screws are no longer than 0.5 inch.

If a screw is longer than 0.5 inch, it can damage the AP chassis.

3If required, suspend the AP by attaching a carabiner to the

hoisting loop on the AP bracket.

NOTE: This kit may include extra screws, nuts and washers. You

may use the extras wherever required.

4Continue with Step 7: Set the Elevation and Tighten Elevation

Bolt.

S -TEP 7: SET THE ELEVATION AND T EIGHTEN LEVA

TION BOLT

1Set the elevation required by the AP.

2Tighten the M8 bolt to 13.6 N-m (10 ft-lbs).

3Continue with Step 8: Powering the AP with AC.

S TEP 8: POWERING THE AP WITH AC

1Separate the AC cable connector parts by unscrewing the boot

from the cable gland and the cable gland from the connector

housing.

2Feed the end of the AC cable through the boot and cable gland.

3Strip the AC cable as shown.

4Insert the stripped part of the conductors into the appropriate

terminals on the connector housing. The conductors are color-

coded and must be connected to the appropriate terminals as

shown in Figure 11.

Typical AC wire colors:

- (Earth Ground): Green (US), Green/Yellow (EU)

- 1 (Neutral/Return): White or Gray (US), Blue (EU)

- 2 (Line/Hot): Black (US), Brown (EU)

- 3 (not used)

NOTE: The color coding of wire conductors varies by region. Before

completing this step, check your local wiring standards for guidance.

5Using a small screwdriver, tighten the small screws around the

connector housing to fix the connector pins into the terminals.

6Mate the cable gland with the connector housing, and then hand-

tighten.

Figure 11: Assembling the AC power connector

Two different-sized grommets are supplied in the AC connector

assembly kit. Use the grommet that is appropriate to the diameter

of the AC cable that you are using.

7Mate the boot with the cable gland, and then hand-tighten to seal.

8Connect the AC cord connector that you have assembled to the

AC power socket on the AP.

9Connect the AC cord to an AC power source.

36mm or 1.42in (max)

9mm or 0.35in (max)

Earth Ground

Neutral/Return

Line/Hot

(not used)

Wire Stripping

(Not Actual Size)

Termékspecifikációk

Márka:	Ruckus Wireless
Kategória:	hozzáférési pont
Modell:	ZoneFlex R710

Szüksége van segítségre?

Ha segítségre van szüksége Ruckus Wireless ZoneFlex R710, tegyen fel kérdést alább, és más felhasználók válaszolnak Önnek

Az Ön neve*

Az Ön e-mail címe*

Írja ide kérdését

Útmutatók hozzáférési pont Ruckus Wireless

Ruckus Wireless ZoneFlex 7372 Útmutató

26 Augusztus 2024

Ruckus Wireless ZoneFlex 7025 Útmutató

26 Augusztus 2024

Ruckus Wireless ZoneFlex T610 Útmutató

26 Augusztus 2024

Ruckus Wireless ZoneFlex 2925 Útmutató

26 Augusztus 2024

Ruckus Wireless ZoneFlex 2942 Útmutató

26 Augusztus 2024

Ruckus Wireless T710 Útmutató

26 Augusztus 2024

Ruckus Wireless ZoneFlex R700 Útmutató

26 Augusztus 2024

Ruckus Wireless R710 Útmutató

26 Augusztus 2024

Ruckus Wireless ZoneFlex R600 Útmutató

26 Augusztus 2024

Ruckus Wireless ZoneFlex 7343 Útmutató

26 Augusztus 2024

Útmutatók hozzáférési pont

Legújabb útmutatók hozzáférési pont

TP-Link Festa F65-Outdoor Útmutató

12 December 2024

TP-Link RE6000XD Útmutató

9 December 2024

Mikrotik Wireless Wire Útmutató

9 December 2024

Mikrotik WAP R Útmutató

9 December 2024

Cisco MR12 Útmutató

14 Október 2024

Draytek VigorAP 920R Útmutató

13 Október 2024

Netgear WNDAP360 Útmutató

12 Október 2024

Cisco 541N Útmutató

9 Október 2024

Cisco Aironet 1815m Útmutató

8 Október 2024

EnGenius ENS1200 Útmutató

5 Október 2024