Használati útmutató Pyle PLMRK47BK

Pyle mélynyomó PLMRK47BK

Olvassa el alább 📖 a magyar nyelvű használati útmutatót Pyle PLMRK47BK (16 oldal) a mélynyomó kategóriában. Ezt az útmutatót 7 ember találta hasznosnak és 2 felhasználó értékelte átlagosan 4.5 csillagra

Oldal 1/16
Marine Stereo Receiver Power Amplifier
AM/FM/MP3/USB/AUX/SD Card Reader Marine
Stereo Receiver, Single DIN, 30 Preset Memory Stations,
LCD Display with Remote Control
www.PyleUSA.com
2
INSTALLATION
Preparation
The preparation kit is necessary to mount the radio on the dashboard, this kit is
available at electronics stores and car audio specialists, check the installation kit
before using it to make sure it is the right one for your vehicle.
INSTALL THE DEVICE
1. Lift the left or right top corner of the plastic outer trim ring
then pull it out to remove it.
2. Insert the two bracket keys into the left and right side of
the chassis to separate the chassis from the housing.
3. Install the mounting knob on the board. Check the
opening size of the sliding panel to be mounted. If the
measurement is not large enough, carefully cut it until it
slips easily on the opening. Do not force the handle in the
opening so as not to bend it. Locate the series of dubbing
tabs above, below and all sides to be mounted. Completely
insert it to the opening of the board, bend the tabs as
necessary towards outside to ensure it ts the board.
4. Slide the stereo into the opening in the dash, ensuring that
the wires behind are tucked and not pinched.
5. Follow the wiring diagram carefully.
Verify you’ve connected them correctly.
CAUTION! Connect the unit to a 12 Volt power source
with adequate ground.
6. Now that your wires are all completed, attach the front
panel and turn the unit (the vehicle must be switched on). If the unit does not ON
work, check the calibration again until the problem is solved. With the new car
stereo secured into the bracket, all you need to do is plug the wiring harness back
into the stereo and put the assembly back into place.
7. Slide the stereo into the opening in the dash, ensuring that the wires behind are
tucked and not pinched. Sometimes this may take a few times when the vehicle
has a tight dash opening. Tuck the wires back into an opening behind the unit.
8. Install the plastic outer trim ring
9. Snap all the pieces of trim back into place over the stereo. Double check that all
screws and trim pieces are securely in place.Try out the new stereo. Turn the car
power on again and play around with the stereo and its settings to be sure
everything is in working order.
www.PyleUSA.com
3
WIRING CONNECTIONS
CONTROL PANEL BUTTONS
WIRING DIAGRAM
PRECAUTION
+12V DC
NEGATIVE
EARTH
AMPLIFIER OUTPUT
White: Rear Output
Left
White: Front Output
Left
Red: Right Front Output
Red: Rear Right Output

Termékspecifikációk

Márka: Pyle
Kategória: mélynyomó
Modell: PLMRK47BK

Szüksége van segítségre?

Ha segítségre van szüksége Pyle PLMRK47BK, tegyen fel kérdést alább, és más felhasználók válaszolnak Önnek




Útmutatók mélynyomó Pyle

Pyle

Pyle PW18SUBA Útmutató

4 Január 2025
Pyle

Pyle PPA15 Útmutató

6 Október 2024
Pyle

Pyle PLRVST400 Útmutató

29 Szeptember 2024
Pyle

Pyle PLMW63 Útmutató

20 Szeptember 2024
Pyle

Pyle PLMRB29W Útmutató

11 Szeptember 2024
Pyle

Pyle PLMRK47BK Útmutató

10 Szeptember 2024
Pyle

Pyle UPLBN122 Útmutató

7 Szeptember 2024
Pyle

Pyle PSBS8 Útmutató

2 Szeptember 2024
Pyle

Pyle PLR38I Útmutató

28 Augusztus 2024
Pyle

Pyle PLRG23C Útmutató

28 Augusztus 2024

Útmutatók mélynyomó

Legújabb útmutatók mélynyomó