Használati útmutató Pro-form PFMC8992

Pro-form Pulzusmérő PFMC8992

Olvassa el alább 📖 a magyar nyelvű használati útmutatót Pro-form PFMC8992 (12 oldal) a Pulzusmérő kategóriában. Ezt az útmutatót 2 ember találta hasznosnak és 2 felhasználó értékelte átlagosan 4.5 csillagra

Letöltés PDF
Oldal 1/12
Heart Rate Monitor User’s Guide Model No. PFMC89820
Model No. PFMC89920
Congratulations for purchasing the new AccuRate™
heart rate monitor. To install and use the heart rate
monitor, read and follow all instructions in this
user’s guide. For detailed instructions about using
the heart rate monitor with your exercise equipment,
refer to the user’s manual included with your exercise
equipment.
This device complies with Part 15 of the FCC rules.
Operation is subject to the following conditions: (1)
this device may not cause harmful interference, and
(2) this device must accept any interference re-
ceived, including interference that may cause unde-
sired operation. Changes or modifications not ex-
pressly approved by ICON Health & Fitness, Inc.
could void the user’s authority to operate this device.
WARNING
If you have an implanted medical device such
as a pacemaker, check with your physician be-
fore using the heart rate monitor.
If you have heart problems, or if you are over 60
years of age and have been inactive, do not use
pulse-driven programs.
If you are taking medication regularly, consult
your physician to find whether the medication
will affect your exercise heart rate.
2
How to Install the Receiver
Before the heart rate monitor can be used, the included receiver must be installed.
To install the receiver in an exercise cycle or an elliptical crosstrainer, refer to the instructions in your exer-
cise cycle user’s manual or elliptical crosstrainer user’s manual. After you have installed the receiver, refer to
pages 10 and 11 of this user’s guide. Note: If you have lost your user’s manual, go to www.iconservice.com on
the World Wide Web, or call toll-free 1-800-999-3756.
To install the receiver in a treadmill, refer to the instructions in your treadmill user’s manual. After you have in-
stalled the receiver, refer to pages 10 and 11 of this user’s guide. Note: If you have lost your user’s manual, go to
www.iconservice.com on the World Wide Web, or call toll-free 1-800-999-3756. If your treadmill user’s manual
does not include instructions for installing the receiver, refer to pages 2 through 9 of this user’s manual.
Pages 2 through 9 include 11 different sections that show how the receiver should be installed in different styles
of treadmills. Find the drawings that most closely resemble your treadmill, and follow the instructions in that sec-
tion to install the receiver. Note: Your treadmill may not look exactly like the treadmills shown in the drawings. If
you have questions, call toll-free 1-800-999-3756.
1. Make sure that the power cord is unplugged. Remove
the indicated Screws from the Console Back (A).
Important: The Screws may be different lengths. Keep
track of which Screws were removed from which holes.
2. Peel the paper off the pad on the bottom of the Receiver
(B). Turn the Receiver so the cylinder is on the side
shown, and press the Receiver into the bottom of the
Console Base (C) in the indicated location.
A
C
Screws
1
2C
B
Cylinder
3. Connect the included Short Jumper Wire (D) to the wire
on the Receiver (B). Connect the other end of the Short
Jumper Wire to the PULSE 2 or PLS2 jack on the back of
the Console (C). If there is a wire already plugged into
the PULSE 2 jack, unplug it. Note: The other wires in-
cluded with the receiver may be discarded. The Wire Tie
can be used to tie wires, if needed.
Make sure that no wires are pinched. See step 1.
Reattach the Console (C) with the Screws. Important: If
the Screws are not put back into the same holes from
which they were removed, the Console will be dam-
aged.
C
PLS2
Jack
PULSE 2
Jack
3
DB
3
1. Make sure that the power cord is unplugged. Remove
the indicated Screws (A) from the Console Back (B).
2. Peel the paper off the pad on the bottom of the Receiver
(C). Turn the Receiver so the cylinder is on the side
shown, and press the Receiver into the bottom of the
Console Back (B) in the indicated location.
Connect the included Short Jumper Wire (D) to the wire on
the Receiver (C). Connect the other end of the Short
Jumper Wire to the PULSE jack on the back of the Console
(E). Note: The other wires included with the receiver may
be discarded. The Wire Tie can be used to tie wires, if
needed.
Make sure that no wires are pinched. See step 1.
Reattach the Console (E) with the Screws (A).
B
E
A
1
2
PULSE
Jack
D
E
C
B
Cylinder

Termékspecifikációk

Márka: Pro-form
Kategória: Pulzusmérő
Modell: PFMC8992

Szüksége van segítségre?

Ha segítségre van szüksége Pro-form PFMC8992, tegyen fel kérdést alább, és más felhasználók válaszolnak Önnek


Útmutatók Pulzusmérő Pro-form

Pro-form

Pro-form PFMC9910 Útmutató

17 Augusztus 2024
Pro-form

Pro-form PFMC8881 Útmutató

10 Augusztus 2024
Pro-form

Pro-form PFMC8992 Útmutató

9 Augusztus 2024

Útmutatók Pulzusmérő

Legújabb útmutatók Pulzusmérő

Garmin

Garmin HRM-DUAL Útmutató

6 Október 2024
Bowflex

Bowflex Heart Rate Armband Útmutató

23 Szeptember 2024
Garmin

Garmin GSC10 Útmutató

16 Szeptember 2024
Polar

Polar A1 Útmutató

16 Szeptember 2024
Polar

Polar M71TI Útmutató

15 Szeptember 2024
Polar

Polar H6 Útmutató

3 Szeptember 2024
Polar

Polar CS Cadence sensor W.I.N.D. Útmutató

2 Szeptember 2024
Timex

Timex T5K738 Útmutató

1 Szeptember 2024
Rossmax

Rossmax SB220 Útmutató

30 Augusztus 2024
Beurer

Beurer PO30 Útmutató

28 Augusztus 2024