Használati útmutató Nitek WB5362

Nitek wifi ismétlő WB5362

Olvassa el alább 📖 a magyar nyelvű használati útmutatót Nitek WB5362 (6 oldal) a wifi ismétlő kategóriában. Ezt az útmutatót 13 ember találta hasznosnak és 2 felhasználó értékelte átlagosan 4.5 csillagra

Letöltés PDF
Oldal 1/6
WB5326
Wireless Bridge
Quick Start Guide
01/09/12
2
Quick Start Guide
WB5326 Outdoor Wireless Bridge
Items Included in Kit
(1) WB5326 RADIO
(1) PoE (48V, 1A)
(1) Mounting Hardware Accessories
(1) Quick Start Guide
(1) Product CD
Hardware Installation
1. Put an Ethernet cable with RJ-45 connector through the water-tight joint. Make the RJ-45 connector as a 568B
wiring configuration:
2. Using the hardware provided mount the Bridge unit in position. Make sure that the Ethernet connection is
facing down. Keep in mind that the unit has a built-in antenna and must have line of sight between units. Refer
to separate mounting guide sheet for illustrations of hardware assembly.
3. Plug water-tight joint side of the Ethernet cable into the Bridge unit. Connect the other end of the cable to the
power injector supplied with the unit. Also connect a standard RJ-45 network cable for the power injector to a
hub or a terminal.
4. There is a ground connection on enna port. The ground connection should the Bridge unit located near the ant
be connected to a proper earth ground point.
5. The antenna of the Bridge unit is behind the plastic face of the unit and must face the other Bridge unit. Make
sure you have line of site to the opposite unit and that they face each other.
Warning Do not mount Bridge unit near electric power lines, electric
lights or near strong electric power signals
6. Power the unit using the supplied PoE inserter.
12345678
568B
21 4
3
Terminal Wire
1 Orange/White
2 Orange
3 Green/White
4 Blue
5 Blue/White
6 Green
7 Brown/White
8 Brown
3
These instructions are designed for configuring this system to be a network Bridge.
1. Power up each Bridge unit for 30 seconds, then RESET it by pressing the Reset button for 10 seconds.
2. On the PC you will be using to setup the Bridge units, select “Network Connections” in the control Panel. You
can get to it by Start>Settings>Control Panel>Network Connections. Locate the “Local Area Connection”
and right click to select “ ”. When in that tab select “Properties Internet Protocol (TCP/IP)”.
3. Set up a computer with a network IP address of:
IP address 192.168.1.100
Subnet 255.255.255.0
Gateway 192.168.1.254
4. Select and note an IP address for each Bridge unit along with an ID name and password for each unit (see
Example 1). You will also need to select a Channel from 1-11 for all units. Bridge units are designed to work as a
pair. Both units of the pair must operate on the same channel. Different sets should use different channels. For
maximum data speed separate sets by 4 channels or more (i.e., 1, 6, 11).
* Each pair of units must operate on the same channel (1 - 11). Different pairs should use different channels.
Example 1
Unit Your IP Address
For each unit Password Unit ID Channel*
1 xxx.xxx.xxx.1 Build 1 Building One 1
2 xxx.xxx.xxx.2 Build 2 Building Two 1
3
4
5
6

Termékspecifikációk

Márka: Nitek
Kategória: wifi ismétlő
Modell: WB5362

Szüksége van segítségre?

Ha segítségre van szüksége Nitek WB5362, tegyen fel kérdést alább, és más felhasználók válaszolnak Önnek


Útmutatók wifi ismétlő Nitek

Nitek

Nitek WB5362 Útmutató

2 Augusztus 2024

Útmutatók wifi ismétlő

Legújabb útmutatók wifi ismétlő

Evga

Evga 100-2W-0028-LR Útmutató

30 Március 2025
Evga

Evga 100-2W-0027-LR Útmutató

30 Március 2025
Mercusys

Mercusys ME80X Útmutató

25 Március 2025
TP-Link

TP-Link RE220 Útmutató

13 Január 2025
Manhattan

Manhattan 525664 Útmutató

12 Január 2025
D-Link

D-Link DMG-112A Útmutató

6 Január 2025
Mercusys

Mercusys Halo H1200G Útmutató

4 Január 2025
HELGI

HELGI HLG0372 Útmutató

3 Január 2025
Medion

Medion P85032 (MD 87070) Útmutató

31 December 2025
TP-Link

TP-Link RE3000X Útmutató

31 December 2025