Használati útmutató NetBotz NBWL0456
Olvassa el alább 📖 a magyar nyelvű használati útmutatót NetBotz NBWL0456 (154 oldal) a Biztonság kategóriában. Ezt az útmutatót 7 ember találta hasznosnak és 2 felhasználó értékelte átlagosan 4.5 csillagra
Oldal 1/154
NetBotz® Appliance
User’s Guide
NBRK0570
NBRK0550
NBRK0450
NBWL0455
NBWL0456
NBWL0355
NBWL0356
This manual is available in English on the enclosed CD.
NetBotz Appliance User’s Guide i
Contents
Preface ............................................................................. 1
U.S. Government Restricted Rights . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Misuse . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Improper Use of Audio/Video Recording Capabilities. . . . . . . . . . . . 1
Availability of Open Source Technologies . . . . . . . . . . . . . . . . . . . . . 1
Introduction ..................................................................... 2
System Definition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Basic Concepts and Terminology . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
SSL Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Web Client: Getting Started ........................................... 4
System Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Choosing a Language. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Supported languages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Accessing the Web Client . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Interface Navigation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Launching Advanced View. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Web Client: Monitoring Your Environment................... 7
Status tab . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Alerts tab . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Cameras tab . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Pods tab . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Sensor History tab . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
NetBotz Appliance User’s Guide ii
Advanced View: Getting Started.................................. 10
System Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Software Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Installing software on a Windows system . . . . . . . . . . . . . . . . . . . 11
Installing software on a Linux system . . . . . . . . . . . . . . . . . . . . . . 11
Adding Appliances . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Removing Appliances. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Accessing an Appliance Using Advanced View . . . . . . . . . . . . . . . 13
Interface Navigation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Navigation pane . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Using folders . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Locking a Navigation pane selection . . . . . . . . . . . . . . . . . . . . . . . 15
Sensor Data Pane . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Action/Information Pane. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Advanced View Menus . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Using Advanced View POST-only Mode . . . . . . . . . . . . . . . . . . . . . . 18
Editing Preferences . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Appearance preferences . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
General preferences . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Network preferences . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Video clip player . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Advanced View: Monitoring Your Environment......... 19
Viewing Sensor Readings and Status. . . . . . . . . . . . . . . . . . . . . . . . 19
Alerting Sensors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Security Sensors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Controlling Rack Access sensors . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Deleting a Pod . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Viewing Live Video . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Pelco PTZ Camera Presets. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Adding a Pelco PTZ Camera Preset . . . . . . . . . . . . . . . . . . . . . . . . 24
Modifying a Pelco PTZ Camera Preset . . . . . . . . . . . . . . . . . . . . . . 24
Renaming a Pelco Camera Preset . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Removing a Pelco Camera Preset . . . . . . . . . . . . . . . . . . . . . . . . . . 24
NetBotz Appliance User’s Guide iv
IPMI Devices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
Adding, editing, and removing IPMI devices . . . . . . . . . . . . . . . . . 50
Sensor settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
Modbus Slave System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
Assigning a slave ID to a pod . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
Removing a slave ID from a pod . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
Viewing the Modbus map . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
Exporting the Modbus map . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
Assigning a register address to a sensor . . . . . . . . . . . . . . . . . . . 53
Removing a register address from a sensor . . . . . . . . . . . . . . . . . 53
Output Control. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
Output control label settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
Output control external port settings . . . . . . . . . . . . . . . . . . . . . . . 54
Output control sensor settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57
Periodic Reports . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58
Configuring periodic e-mail reports . . . . . . . . . . . . . . . . . . . . . . . . 58
Configuring periodic FTP reports . . . . . . . . . . . . . . . . . . . . . . . . . . 59
Configuring periodic HTTP reports . . . . . . . . . . . . . . . . . . . . . . . . . 61
Rack Access Pods . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62
Configuring the Rack Access Pod settings . . . . . . . . . . . . . . . . . . 62
Configuring the Rack Access Pod sensors . . . . . . . . . . . . . . . . . . 63
Threshold configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63
Rack Access System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64
About the Rack Access System dialog . . . . . . . . . . . . . . . . . . . . . . 64
Selecting a card format . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64
Registering cards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64
Registering a card manually . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65
Editing card information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65
Deleting a card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65
Assigning doors to a card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65
Copying permissions between cards . . . . . . . . . . . . . . . . . . . . . . . 66
Removing a door from a card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66
Adding an appliance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67
Removing an appliance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67
Editing an appliance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67
Sensor Pods . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68
Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69
Sensors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69
External ports . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70
NetBotz Appliance User’s Guide v
Advanced View: Configuring Appliances ................... 74
Backup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74
Clock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74
Custom Audio Clips . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75
Adding custom audio clips . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75
Deleting custom audio clips . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75
Data Center Expert . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75
DNS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76
Configuring DNS settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76
Configuring dynamic DNS settings . . . . . . . . . . . . . . . . . . . . . . . . . 76
E-mail Server . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77
External Storage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77
Using an external storage system . . . . . . . . . . . . . . . . . . . . . . . . . . 78
Using a Windows share . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79
Using an NFS mount . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80
Removing external storage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80
Reclaiming external storage data . . . . . . . . . . . . . . . . . . . . . . . . . . 81
IP Filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82
Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82
Adding new filters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82
Filter fields . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 83
Configuring IP filters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 84
Using CIDR bit-masks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 84
Example configurations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85
License Keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 86
Location . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 86
Log . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 86
Modbus Slave Communication . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 87
Network Interfaces . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 88
PPP/Modem . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 89
Managing your appliance using a dial-In PPP connection . . . . . . 91
PPP performance considerations . . . . . . . . . . . . . . . . . . . . . . . . . . 91
Using SIM security . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 92
Upgrading over PPP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 92
NetBotz Appliance User’s Guide vi
Pod, Pelco Camera, and Rack Access PX-HID Sharing. . . . . . . . . .93
Setting up a Pelco shared IP camera pod . . . . . . . . . . . . . . . . . . . . 95
Setting up shared IP camera pods . . . . . . . . . . . . . . . . . . . . . . . . . . 95
Proxy. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .97
Rack Access Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .97
Region . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .98
Configuring the available language files . . . . . . . . . . . . . . . . . . . . . 98
Restore . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .99
Serial Devices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .99
SMS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .100
SNMP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .101
SSL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .102
Upgrade . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .103
Users. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .103
Lost password recovery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 105
Web Server. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .106
Basic Tab . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 106
Advanced tab . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 106
Wireless Sensor Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .107
Add Addresses . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 108
Configure Coordinator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 109
Safely Remove Coordinator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 109
Wireless Sensor Firmware Update . . . . . . . . . . . . . . . . . . . . . . . . . 109
Advanced View: Defining Thresholds .......................110
Defining Analog Thresholds. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .110
Defining State Thresholds . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .112
Advanced Threshold Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . .114
1NetBotz Appliance User’s Guide
Preface
U.S. Government Restricted Rights
Restricted rights legend. Use, duplication, or disclosure by the Government is subject to restrictions as
set forth in subparagraph (c) (1) (ii) of the Rights in Technical Data and Computer Software clause at
DFARS 252.227-7013 or subparagraphs (c) (1) and (2) of the Commercial Computer Software-
Restricted Rights clause at CFR 52.227-19, as applicable.
Misuse
Use your appliance ONLY in the manner specified. If the equipment is used in a manner not specified,
the protection provided by the equipment may be impaired. APC is not responsible for misuse.
Improper Use of Audio/Video Recording
Capabilities
Attention: THE EQUIPMENT CONTAINS, AND THE SOFTWARE ENABLES, AUDIO/VISUAL
AND RECORDING CAPABILITIES, THE IMPROPER USE OF WHICH MAY SUBJECT YOU TO
CIVIL AND CRIMINAL PENALTIES. APPLICABLE LAWS REGARDING THE USE OF SUCH
CAPABILITIES VARY BETWEEN JURISDICTIONS AND MAY REQUIRE AMONG OTHER
THINGS EXPRESS WRITTEN CONSENT FROM RECORDED SUBJECTS. YOU ARE SOLELY
RESPONSIBLE FOR INSURING STRICT COMPLIANCE WITH SUCH LAWS AND FOR STRICT
ADHERENCE TO ANY/ALL RIGHTS OF PRIVACY AND PERSONALTY. USE OF THIS
SOFTWARE FOR ILLEGAL SURVEILLANCE OR MONITORING SHALL BE DEEMED
UNAUTHORIZED USE IN VIOLATION OF THE END USER SOFTWARE AGREEMENT AND
RESULT IN THE IMMEDIATE TERMINATION OF YOUR LICENSE RIGHTS THEREUNDER.
Availability of Open Source Technologies
This product includes technologies that are governed by the GNU Public License. The GPL source code
contained in our products is available for free download from:
http://support.netbotz.com/gpl
2NetBotz Appliance User’s Guide
Introduction
The Schneider Electric NetBotz® Web Client and Advanced View each provide a software interface for
monitoring and controlling your NetBotz security and environmental monitoring system with the
following NetBotz appliances:
NetBotz Rack Monitor 450, NetBotz Rack Monitor 550, NetBotz Rack Monitor 570, NetBotz Room
Monitor 455, and NetBotz Room Monitor 355.
You use the Web Client interface primarily to monitor the environment. You use the full-featured
Advanced View to monitor the environment and for system administration. This NetBotz Appliance
User’s Guide explains how to use both the Web Client and Advanced View.
System Definition
Your NetBotz security and environmental monitoring system may consist of one or more appliances.
When using the Web Client or Advanced View, you select one appliance on which to view sensor
readings, live video, and associated devices. Devices associated with the appliance are typically NetBotz
camera or sensor pods connected to the appliance, or supported third-party cameras or other supported
devices that have security and environmental monitoring capabilities.
Basic Concepts and Terminology
Sensor pod and camera pod. The terms Sensor Pod and Camera Pod are commonly used in both the
Web Client and Advanced View. These terms refer to the two categories of devices that make up your
NetBotz security and environmental monitoring system. Sensor pods typically have multiple internal
sensors or sensor ports for connecting APC or third-party sensors. The NetBotz product line consists of
various sensor pods and camera pods, but in the Web Client and the Advanced View software interface,
references to pods goes beyond the NetBotz products to include other devices, such as Pelco IP cameras
and the Rack Access PX-HID. In addition, the functionality of NetBotz appliances is divided into sensor
pod functionality and camera pod functionality and is initially labeled in the Web Client and Advanced
View as Sensor Pod (Integrated) and Camera Pod (Integrated).
Shared devices. Depending on the hardware and software that you purchased for use with your
NetBotz security and environmental monitoring system, you may be able to monitor remote devices on
your network (for example, Pelco IP cameras, the Rack Access PX-HID, and NetBotz appliances) from
one screen in Advanced View or the Web Client. This feature is called Pod Sharing. If you use Pod
Sharing, remote devices are initially labeled as Shared.
For additional details on shared devices, see “Pod, Pelco Camera, and Rack Access PX-HID
Sharing” on page 93.
3NetBotz Appliance User’s Guide
SSL Support
By default, Secure Sockets Layer (SSL) is enabled on your NetBotz appliance. All browser/appliance
interaction can be carried out using SSL by connecting to the appliance using a URL beginning with
https (for example, https://IP_address). Your appliance can also use SSL when posting alert notification
and sensor data to Web servers, and Advanced View can be configured to use SSL when communicating
with your appliance.
The SSL certificate needed for SSL communications is generated by the appliance (self-signed) and
requires no user interaction. If the hostname or domain name of the appliance is changed, the certificate
automatically regenerates. You can also request and install a signed SSL certificate from a certification
authority.
For information on how to install a signed SSL certificate, see “SSL” on page 102.
Note: Your browser generates a warning the first time you attempt to communicate with the
appliance using SSL after a self-signed SSL certificate has been created. This is normal
behavior and you can accept the certificate.
To use SSL when communicating with the appliance using the Web Client, use https:// at the beginning
of the appliance Web address.
For more information about the Web Client see “Web Client: Monitoring Your
Environment” on page 7.
To use SSL when posting alert notifications and sensor data to a Web server, use https:// at the
beginning of the Web address of the Web server when configuring the Send Using HTTP Post Alert
Action.
For information on configuring Send Using HTTP Post Alert Actions, see “Creating or
editing alert actions” on page 32 and “Creating a send HTTP post alert action” on page 128.
To use SSL when monitoring or managing your appliance using Advanced View, select Use SSL in the
Advanced View interface.
For more information about Advanced View, see “Advanced View: Getting Started” on
page 10.
4NetBotz Appliance User’s Guide
Web Client: Getting Started
The NetBotz Web Client provides a real-time overview of alerts and device details for a NetBotz
appliance running at least version 4.2. It does not require the Advanced View application and Java
Runtime Environment.
You can use the Web Client to view a list of active and resolved alert conditions: images captured by
camera pods connected to the appliance, and sensor readings reported by camera pods; sensor pods;
external sensors connected to sensor pods; devices monitored using scanners; and graphs of collected
sensor data. Additionally, you can activate relay output actions and configure sensors.
By default, Secure Sockets Layer (SSL) is enabled on the NetBotz appliance. The SSL certificate is
generated by the appliance (self-signed) and requires no user interaction.
System Requirements
The Web Client has been tested on the following Web browsers. Other versions may work, but have not
been tested.
• Microsoft® Internet Explorer® 8.x, 9.x
• Google Chrome® 23
• Firefox® 17.0
• Safari® 5.17
NetBotz appliances also support a simplified version of the Web Client that can be viewed using the
following mobile devices and tablets. Other mobile devices and tablets may work, but have not been
tested.
Mobile devices
• iPhone® 3GS
• iPhone® 4
• iPod® Touch
• Android® 2.2+
• BlackBerry® 6.0
Tablets
• iPad®
• iPad®
• 2 Android®2.2+
• Firefox® 3.0
6NetBotz Appliance User’s Guide
Interface Navigation
The Web Client interface is divided into five tabs: Status, Alerts, Cameras, Pods, and Sensor
History:
Status: Provides information at a glance about alerting sensors, security sensors, and cameras.
Alerts: Displays alerts from the device types and severities you select, All by default.
Cameras: Displays live video captured by the appliance, the cameras connected to the appliance, or IP
cameras on your network that are shared through the appliance.
Pods: Allows you to view data from Sensor, Rack Access, or Camera pods you select.
Sensor History: Displays data from a sensor pod and sensor you select, at an interval you select, in a
graph.
Launching Advanced View
If you wish to switch to the Advanced View application, you must launch it from its install directory on
your system. If Advanced View is not installed on your machine, a link in the Web Client help opens a
web page where you can download and install the program. Advanced View is not supported on mobile
devices.
Note: You must have at least the 1.6.0_12 version of the JRE installed to run Advanced
View.
7NetBotz Appliance User’s Guide
Web Client: Monitoring Your
Environment
The Web Client provides a real-time overview of alerts and device details, including sensor readings and
images captured by camera pods, for a NetBotz appliance running at least version 4.2. It does not require
the Advanced View application and Java Runtime Environment.
By default, Secure Sockets Layer (SSL) is enabled on the NetBotz appliance. The SSL certificate is
generated by the appliance (self-signed) and requires no user interaction.
To access the Web Client, enter the hostname or IP address of the appliance in a browser. Once you log
in, you can view data according to the privilege set assigned to your user account.
The interface is divided into five tabs: Status, Alerts, Cameras, Pods, and Sensor History.
Status tab
The Status tab provides an overview of the devices monitored by the NetBotz appliance.
Note: For an air flow sensor, data must be accumulated for 15 to 30 minutes before accurate
air flow readings are available. After power is applied to the device, air flow sensor data
appears as N/A until enough data is collected.
• Alerting Sensors: Displays the sensors reporting alerts, and their severity, at all the devices
monitored by the NetBoltz appliance.
You can select a sensor to view its details, and change its label or sensor value history, or
choose whether to report unplugged errors, if necessary.
• Security Sensors: Displays pods and sensors reporting rack access alerts, and their severity, at all
the devices monitored by the NetBoltz appliance (available only when a rack access device is
managed by the NetBotz appliance).
You can select a sensor to view its details, and change its label, if necessary.
Security sensors include all Door sensors, Handle sensors, and Lock sensors connected to a
Rack Access Pod 170, and any Door, Handle, or Lock sensors connected to a pod-shared Rack
Access PX-HID appliance.
• Cameras: Displays thumbnail views and identification information for all the cameras monitored
by the NetBotz appliance, regardless of whether an alert is reported.
You can select a camera to view its details, change the resolution and refresh rate, or change
the camera angle (supported cameras only).
• Maps: Displays the device maps created in the NetBotz Advanced View, showing the location of
pods and sensors, and the alert state of the devices on the map. You use the Advanced view to
create, edit, or delete a map.
When more than one device map is stored on the appliance, the first map in the list is
displayed by default. You can select from the list to view additional device maps. You can
select a device in a map to view the readings and alerts for each sensor.
9NetBotz Appliance User’s Guide
Depending on the pod type selected, one or more of the following options are available:
• Settings: Allows you to change the pod label.
• External Sensor Ports: Allows you to select the sensor type, and change the port label.
• Pod Details: Displays details for the selected pod, including the name, model,
manufacturer, revision, bootstrap verison, and application version.
You can select a sensor to change its label or sensor value history, or choose whether to report
unplugged errors, when applicable. A toggle switch is displayed for supported state sensors.
Sensor History tab
The Sensor History tab allows you to view historical sensor data in a graph, for a sensor and interval
you select.
Note: The start time available is dependent upon the value you specify for Sensor Value
History in the Settings section of the Pods tab.
10NetBotz Appliance User’s Guide
Advanced View: Getting Started
Advanced View is a stand-alone Java application you can use to monitor and configure your appliance
and any camera pods, sensor pods, CCTV adapter pods, output relay pods, 4-20 mA sensor pods,
external sensors, or supported serial-based sensors connected to the appliance.
Note: Your monitor must be set to at least 1024x768 for Advanced View to display properly.
System Requirements
To run the Advanced View software application, your personal computer must meet these system
requirements:
• x86-compatible (32-bit or 64-bit) processor
• Supported operating systems:
– Microsoft® Windows® XP Pro SP2 or SP3
– Windows Vista® Business or Enterprise
– Windows 7
– Red Hat ® Enterprise Linux® version 5 running X Windows
– Red Hat Fedora® 10 or 11
• 120 MB of free disk space
• A monitor capable of displaying a resolution of 1024x768
12NetBotz Appliance User’s Guide
Adding Appliances
Before using Advanced View to manage an appliance, you must first add the appliance IP address or
hostname to the Appliance list. To add an appliance to the Appliance list:
1. Click Add Appliance. The Add Host Device window opens.
2. In the IP Address or Hostname field, type the IP address or hostname of the appliance.
3. In the Port field, type the TCP port through which you will communicate with this appliance.
The default value is 80.
4. To use SSL encryption to communicate with this appliance, check Connect Using SSL.
5. If you want to be logged out after a period of inactivity, select Auto Logoff and specify the length
of idle time before you are logged out in the provided field. Click OK.
Once you have added an appliance to the Appliance list, Advanced View automatically loads data from
the appliance into Advanced View. Navigate to an appliance by selecting the appliance address or
hostname from the Appliance list. If you specified Use SSL when adding the appliance, SSL appears in
the selection list beside the appliance IP address or hostname.
Removing Appliances
To remove an appliance from the Appliance list:
1. Select Remove Appliance from the File menu. The Remove Appliance window opens.
2. Select the appliance you want to remove from the list of appliances.
3. Click Remove to remove the appliance from the Appliance list.
13NetBotz Appliance User’s Guide
Accessing an Appliance Using Advanced View
Select an appliance from the Appliance list.
• If the appliance Guest account is configured with a Sensor (No Camera), Sensor, Application,
or Administrator privilege set, you are automatically granted access to the appliance and can
view Advanced View panes permitted by the privilege set. If you have a user account on the
appliance with greater privileges than those allowed to guests, click Logon at the top of the
Advanced View interface and enter your User ID and Password.
• If the Guest account is configured with no privileges (privilege set of None), you must provide a
User ID and Password. Once you have logged in, you can view the Advanced View panes that
are permitted by the privilege set assigned to your user account.
For more information, see “Users” on page 103.
Note: The Application, Application (with Alert Update), and Sensor (No Camera) privilege
sets are only available with the purchase of the Advanced Software Pack. They are standard
on the NetBotz Rack Appliance 550 and NetBotz Rack Appliance 570.
Advanced View panes accessible by privilege set
Privilege Set Accessible Panes
Administrator Gives user access to all information and configuration icons
available on the appliance.
Application (with Alert Update) Gives user access to the Navigation, Sensor Data, and selected
portions of the Information/Action panes. Users can view the
Camera, Graphs, Alerts, History, and About panes. Users can also
resolve alert conditions for thresholds that have been configured
with the Return-To-Normal Requires User Input setting in
their Advanced Settings.
Note: This privilege set does not permit access to the
Configuration pane.
Application Gives user access to the Navigation, Sensor Data, and selected
portions of the Information/Action panes. Users can view the
Camera, Graphs, Alerts, History, and About panes.
Note: This privilege set does not permit access to the
Configuration pane and the user cannot resolve alert conditions
for thresholds configured with the Return-To-Normal Requires
User Input setting in their Advanced Settings.
Sensor Gives user access to the Navigation, Sensor Data, and selected
portions of the Information/Action panes. Users can view the
Camera, Graphs, History, and About panes.
Note: This privilege set does not permit access to the Alerts or
Configuration panes.
Sensor (No Camera) Gives user access to the Navigation, Sensor Data, and selected
portions of the Information/Action panes. Users can view the
Graphs, History, and About panes.
Note: This privilege set does not permit access to the Cameras,
Alerts, or Configuration panes.
None No access to any appliance features.
14NetBotz Appliance User’s Guide
Interface Navigation
The Advanced View interface is divided into the Navigation pane, the Sensor Data pane, and the Action/
Information pane.
Navigation pane
Located in the upper-left corner of the interface, the Navigation pane displays:
• An appliance and camera pods and sensor pods connected to the appliance
• Serial-based sensors being monitored using scanners
• Alerting sensors
• Shared devices, such as shared IP cameras
Click a device in the Navigation pane to display all sensors associated with the device in the Sensor Data
pane.
Right-click a device in the Navigation pane and select Configure Pod to modify the sensors, settings,
and external ports associated with the device.
See “Scanned Devices” on page 44.
Pods connected to your appliance automatically appear in the Navigation pane. Newly-added pods are
labeled by their pod type and their serial number.
For details on changing labels, see “Camera Pods” on page 36, “Sensor Pods” on page 68, or
“Output Control” on page 53.
If you connect a pod to the appliance and then disconnect it, the pod remains in the Navigation pane, but
the icon is grayed out. If you reconnect the pod, its Navigation pane entry becomes active again.
Using folders
The Navigation pane lists all devices associated with the appliance. You can create folders in the
Navigation pane to form virtual groups of devices. Devices included in a folder are also listed in the
selection list. A single device can be included in multiple folders. When a folder is not expanded, if any
one device in the folder is in an alert status, the folder will be red.
Folders can be created, modified, or deleted only using Advanced View. Any folders created using
Advanced View are visible in the Web Client.
15NetBotz Appliance User’s Guide
To create or modify a folder:
1. Right-click on the background of the Navigation pane, not on a device, and select Add Folder.
To modify a folder, right-click on the folder and select Modify Folder.
2. Type a folder name in the Folder Name field.
3. To add devices, select one or more devices from Available Enclosures and click the right arrow
(>) button to add the selected devices to the Selected Enclosures list.
4. To remove devices, select one or more devices from Selected Enclosures, and click the left
arrow (<) button to move the selected devices to the Available Enclosures list.
5. Click OK.
To delete a folder, right-click on the folder and click Delete Folder.
Locking a Navigation pane selection
You can lock the Navigation pane so that only a specific device is selected. Once the Navigation pane is
locked, Advanced View automatically starts with the pane in the locked state.
To lock the pane to a specific device:
1. Select a device.
2. Right-click on the device and select Lock selection.
3. To unlock the pane, right-click on any device in the Navigation pane and clear the check box for
the Lock selection option.
16NetBotz Appliance User’s Guide
Sensor Data Pane
Located in the lower-left hand corner of the interface, the Sensor Data pane displays the readings and
alert status of sensors associated with the selected device in the Navigation pane. If the selected device is
an output relay device, the state of the relay is displayed.
If the selected device features a large number of sensors, the sensors may be divided into sensor sets. Use
the Set drop-down list to select either a specific sensor set or All Sensors.
Right-clicking on a sensor in the Sensor Data Pane reveals a drop-down menu with the following
options:
• Configure sensor...
Select this option to display the Sensor Configuration window, where you can modify the
settings and thresholds for the available sensors.
• View graph
Select this option to display the Graph View pre-populated with the current sensor.
• View History
Select this option to display the History View pre-populated with the current sensor.
Action/Information Pane
Use the Action/Information pane, located on the right-hand side of the interface, to view information and
perform configuration tasks on your appliance and pods. The following views are available from the
Action/Information pane:
• Camera View: This view displays live video captured by the appliance, cameras connected to the
appliance, or IP cameras on your network that are shared through the appliance. You can listen to
an audio stream from a selected camera pod or CCTV adapter pod and transmit audio from a
microphone connected to a computer running Advanced View to a selected camera pod or CCTV
adapter pod. If relay outputs are associated with a camera pod, buttons for each switch or relay
appear on the camera image to which they correspond.
See “Output Control” on page 53.
• Alerts View: This view displays alerts and resolved alerts reported by the appliance, any pods
connected to the appliance, or any devices being monitored by scanners.
• Maps View: This view displays maps that you configure for use with the appliance. A device
with a red background has an alert status. A device with a green background has a status of OK.
• Graph View: This view displays a graph of up to 24 hours of environmental data collected from
any sensors or devices associated with an appliance.
• History View: This view displays a historical set of data for a chosen appliance or sensor set. This
data can be exported to a text file for import into another application.
• Configuration View: Use this view to configure your appliance, pods connected to the appliance,
and sensors, plus various other system settings and features.
• About View: This view displays information about your appliance and all connected pods.
17NetBotz Appliance User’s Guide
Advanced View Menus
Advanced View features the following menu bar:
• File: Use this menu to add appliances to or remove appliances from the Appliance selection
drop-down list and to exit the Advanced View application.
• Edit: Use this menu to cut, copy, paste, and delete text, and to configure Preferences.
See “Editing Preferences” on page 18.
• Tools: Use this menu to complete the following tasks:
– View Messages (information generated by Advanced View for logging and debugging
purposes).
– Put the appliance in Advanced View POST-only Mode. This mode is only for appliances
located behind a firewall. This mode does not permit StruxureWare Data Center Expert
appliances to access the appliances directly.
– View the Appliance Log.
See “Log” on page 86.
– View the Event Log.
See “Event Log” on page 29.
– Reboot the appliance.
– Change the Root Password.
Note: The Root Password only affects console access to the device. It should only
be changed by advanced users.
– Access the Configuration Wizard.
Only user accounts with administrator privileges have full access to the Tools
menu. For more information, see “Users” on page 103.
• Window: Use the Window menu to launch a New Window or to switch between multiple
Advanced View windows.
• Help: Use this menu to access information about Advanced View and to access context-sensitive
help.
18NetBotz Appliance User’s Guide
Using Advanced View POST-only Mode
If you use StruxureWare Data Center Expert to monitor and manage a NetBotz appliance that is located
behind a firewall, StruxureWare Data Center Expert may not be able to communicate directly with the
appliance. Placing the appliance in Advanced View POST-Only Mode causes the appliance to post all
monitoring data to a specified StruxureWare Data Center Expert appliance at a user-specified interval.
SSL encryption can be used for secure data posting.
To use the Advanced View POST-Only Mode:
1. From Advanced View, log in to the appliance using a User account with administrator privileges.
2. From the Tools menu, select Advanced > Advanced View POST-Only Mode.
3. Click Add to open the Advanced View POST-Only Mode Configuration window. Enter your
information and click OK.
Editing Preferences
With Advanced View you can configure preferences that apply to the appearance and functionality of the
Advanced View user interface. These settings are saved on your client system, not on your appliance.
Select Preferences from the Edit menu. Choose from the following preference categories:
• Appearance
• General
• Network
• Video Clip Player
Appearance preferences
To edit your client Appearance settings, open the Client Preferences window and select Appearance
from the Category list. Select an option from the Look and Feel drop-down menu, define whether the
Toolbar should include text and icons, and choose the size of those elements. When you are finished,
click OK.
General preferences
To edit the General settings for the client, open the Client Preferences window and select General from
the Category list. Configure the browser location, restore the Advanced View window to full size when
an alert occurs, and force Advanced View to ignore the default setting of the clock and to use either a
12-hour or 24-hour clock. When you are finished, click OK.
Network preferences
To edit your client Network preferences, open the Client Preferences window and select Network from
the Category list. Configure the connection time-out, choose a direct connection for camera images, and
enter the proxy configuration information. When you are finished, click OK.
Video clip player
To specify the maximum amount of disk space allocated for use by the Video Clip Player, open the
Client Preferences window and select Video Clip Player from the Category list. Specify the maximum
number of megabytes of disk space available to the Video Clip Player, and click OK.
19NetBotz Appliance User’s Guide
Advanced View: Monitoring Your
Environment
Use Advanced View to view sensor readings, view camera images, graph collected sensor data, and view
active and resolved alert conditions. You can also create, view, and delete maps for use in the Map view.
Viewing Sensor Readings and Status
To view sensor readings, select a device that includes sensors from the Navigation pane. The Sensor
Data pane automatically updates with sensor information for the device you selected. Any sensors with
an alert status have a background color of red.
If the device has a large number of sensors, the sensors are divided into sensor sets. If the sensors are
divided into sets, you have the following options:
• To display all of the sensors for the selected device, select All Sensors from the Set drop-down
list.
• To view only the sensors in a sensor set, select the sensor set from the Set drop-down list.
Note: For an air flow sensor, data must be accumulated for 15 to 30 minutes before accurate
air flow readings are available. After power is applied to the device, air flow sensor data
appears as N/A until enough data is collected.
Alerting Sensors
Selecting the Alerting Sensors entry in the Navigation pane provides a list of all local or pod-shared
sensors that are currently generating an alert. The alerting sensors are listed in the Sensor Data pane.
Security Sensors
Selecting the Security Sensors entry in the Navigation pane provides a list of all security-related sensors
that are currently generating an alert in the Sensor Data pane. Security sensors include all Door sensors,
Handle sensors, and Lock sensors connected to a Rack Access Pod 170, as well as any Door, Handle, or
Lock sensors connected to a pod-shared Rack Access PX-HID appliance.
Controlling Rack Access sensors
If you have an SP170 Rack Access Pod connected to your appliance, you can lock and unlock rack locks
and enable or disable card reader hardware using the Web Client or Advanced View. The user account
must have “Sensor” or “Administrator” privileges in order to access this functionality.
To lock or unlock a rack lock in Advanced View:
1. From the Navigation pane, select a Rack Access Pod.
2. Right-click a lock sensor in the Sensor Data pane.
3. Select Lock (n): Set to “Unlocked”. The reading will change to Unlocked and the menu item
will read Lock (n): Set to ‘Locked’. The lock will automatically relock in 10 seconds by default.
This setting can be changed in the Rack Access Settings configuration dialog.
20NetBotz Appliance User’s Guide
To enable or disable a card reader in Advanced View:
1. From the Navigation pane, select a Rack Access Pod.
2. Right-click the Reader sensor in the Sensor Data pane.
3. Select Reader (n): Set to “Disabled” next to the desired card reader. The reading will change to
Disabled and the button label will read Reader (n): Set to “Enabled”.
Note: A physical key can always be used to access the rack regardless of whether
the card reader is enabled or disabled.
Deleting a Pod
When a pod is disconnected from an appliance, you can delete it from the Navigation pane. You cannot
delete integrated pods.
1. Disconnect the pod from the appliance. The symbol for the pod in the Navigation pane will dim.
2. From the Navigation pane, right-click the pod and select Delete pod.
3. Click Remove to confirm the deletion.
21NetBotz Appliance User’s Guide
Viewing Live Video
Click the Camera View button in the Action/Information pane to view live video captured by the
appliance, cameras connected to the appliance, or shared IP cameras on your network. Controls are
applied to the top-most camera image. Click an image to change its position to the top. To view all
camera images side by side, click the Tiled check box.
For information on shared IP cameras, see “Pod, Pelco Camera, and Rack Access PX-HID
Sharing” on page 93.
Standard camera controls
Control Description
Mode To change the size of the image, right-click the camera image, and select Configure
Camera. Select Settings, and, from the Mode drop-down list, choose dimensions
(resolution) for the image. The dimensions 640x480, for example, mean 640 pixels wide by
480 pixels high. NOTE: As the image dimensions increase, the maximum image rate
available will decrease.
Rate To change the frame rate, that is, the frequency that the video image is updated, make a
selection from the Refresh Rate drop-down list in the Camera View. NOTE: The
maximum rate available is determined by the mode setting (described above) and, if
applicable, the image quality settings.
NOTE: The maximum frame rate for shared IP cameras is limited to 15 frames per second.
For more information on image quality settings, see “Capture settings” on page 38.
For more information on shared IP cameras, see “Pod, Pelco Camera, and Rack Access PX-
HID Sharing” on page 93.
Zoom This zoom feature does not apply to Pelco PTZ cameras. See “Pelco PTZ camera controls”
on page 22 for details on the zoom features for Pelco PTZ cameras.
1. To avoid distortions, right-click the camera image and select Maintain aspect ratio.
2. Within the camera image, click and drag to draw a box around the area of interest.
3. Right-click the camera image and select Zoom in.
4. To return to the full camera image, right-click and select Zoom out.
Only available when a microphone is connected to the NetBotz appliance or a pod. Click to
listen to streaming audio. Click again to turn off the audio.†
Only available when speakers are connected to the NetBotz appliance or a pod. Click and
hold the button while speaking into your system microphone. NOTE: While transmitting
audio, you will not be able to hear audio from the device.†
†These audio features are only available when the Advanced Software Pack has been installed on
the system running Advanced View. The Advanced Software Pack is included with a NetBotz 550
or NetBotz 570 appliance, but must be purchased separately when using any other NetBotz
appliance. To check if the software pack has been installed, click the Configuration button, then
click License Keys from the Appliance Settings area.
23NetBotz Appliance User’s Guide
Resize Camera
View
View a part of the image in more detail. Click this button, and then on the
image, click and drag a box around the area of interest. When you release the
mouse button, the camera automatically zooms to the box you created.
Center Click this button and then click a point on the image to center the image on
that point.
Control Name Description
24NetBotz Appliance User’s Guide
Pelco PTZ Camera Presets
The Pelco camera preset controls allow you to associate a name with a camera position, and save it. You
can modify the camera position of a preset, or rename it.
Adding a Pelco PTZ Camera Preset
To create, modify, or remove presets for the selected Pelco camera:
1. Click the Update button from the Action/Information pane.
2. On the Presets tab, in the Add/Update Preset field, specify the name of a new preset, and click
Add, then click OK.
3. To modify the name of an existing preset, select it from the Presets drop-down list, specify the
new name, and click Update, then click OK.
4. To remove a preset, select it from the Presets drop-down list, and click Remove, then click OK.
Modifying a Pelco PTZ Camera Preset
To modify the camera position of an existing preset for the selected Pelco camera:
1. Reposition the camera using the Pelco camera controls.
2. Click the Save Preset button.
3. Select the Overwrite an existing preset option, and select the name of the preset you want to
modify from the drop-down list.
4. Click OK.
Renaming a Pelco Camera Preset
To rename a preset for the selected Pelco camera:
1. Click the Manage Presets button.
2. Select the preset from the list in the display.
3. Select Rename, specify the new name, and click OK.
4. Click OK.
You must click OK to save any changes.
Removing a Pelco Camera Preset
To delete a preset for the selected Pelco camera:
1. Click the Manage Presets button.
2. Select the preset from the drop-down list.
3. Click Remove, then click OK.
You must click OK to save any changes.
25NetBotz Appliance User’s Guide
Recording Camera Images
Use Advanced View to record camera images and save them to a user-specified directory. By default,
recorded camera images are saved to a subdirectory with the same name as the camera pod, located
within a directory named camera in your Home directory. For example, a user account named NetBotz
on a Windows XP system recording images from a camera pod labeled My Camera would store
recorded images in the directory C:\Documents and Settings\NetBotz\camera\My Camera.
Images are stored as JPG files, and are named imagexxx.jpg by default, where xxx is a picture count
number that is automatically incremented as images are captured and saved.
To specify camera recording settings, right-click in the camera image and select Preferences. Specify
the directory in which camera images are stored, the file name used when recording camera images, and
a maximum number of pictures or a maximum amount of disk space used to store recorded images on
your system.
To record camera images to your hard drive, right-click on an image and select Record images.
Viewing Alerts
To view alert conditions reported by your appliance or attached pods or sensors:
1. Click the Alerts View button from the Action/Information pane.
2. From the Pods drop-down list, select the appliance, pod, or other device to check for alert
conditions. By default, the appliance is selected. To view alert conditions for the appliance and
all connected pods, select All from the Pods drop-down list.
3. Use the Refresh Interval drop-down list to specify how often the Alerts View content is
updated. Click the Refresh button to refresh the contents of the Alerts View immediately. The
default refresh rate is 15 seconds.
4. To view resolved alert conditions, check Include Return to Normal. By default, resolved alerts
are stored on the appliance for up to 24 hours. The period of time for which resolved alerts are
available on the appliance is configured using Advanced View.
Active and resolved alerts for the selected sensor are displayed in a table on the Alerts panel. Alert-
specific data for resolved alerts is shown in italics. The following information is available for each active
or resolved alert condition:
• Time: The time at which the alert occurred. A second time stamp indicates the time at which the
alert was resolved.
• Severity: The severity of the alert. Severity values, from most severe to least severe, are Failure,
Critical, Error, Warning, and Information.
• Sensor/Device: The device or sensor reporting the alert.
• Alert Type: A brief description of the alert.
• Description: A detailed description of the conditions that caused the alert.
To view detailed information about an alert, double-click the alert. A new window opens, displaying
detailed information about the alert, including the value reported by the sensor that reported the alert, the
sensor port to which the sensor is connected, and the alert ID. Click Close to return to the Alerts view.
27NetBotz Appliance User’s Guide
Creating and editing maps
To create a new map for use in the Map View or to edit a map:
1. Click the Maps View button in the Action/Information pane.
2. To create a new map, click Add. To edit a map, select the map from the Maps drop-down list and
click Edit. The Map Configuration window opens.
Note: There is a limited amount of space available for creating maps and using
custom audio clips. The Storage Information area at the bottom of the window shows
the storage space used and the total storage space available.
3. Enter a name in the Name field.
4. A default background image is provided for the map. To use a different image, click Change
Background Image. Select a graphic file (JPG, PNG, or GIF format, no larger than 640x480)
and click OK.
5. Place devices or sensors on the map. To position a device on the map, select the device symbol
from the device directory structure at the left side of the window and click Add Selected Pod/
Sensor, or click and drag the icon from the directory structure onto the map.
– To specify a new label for symbols on the map, right-click on the symbol, then click Change
map label.... Type the new label for the symbol and click OK.
– To remove a symbol from the map, right-click the symbol, then click Remove.
6. When you have finished placing symbols on the map, click OK to save the map to your
appliance.
Viewing Graphs
To view a graph of the data collected by a sensor connected to your appliance:
1. Click the Graph View button in the Action/Information pane.
2. Select the pod from the Pods drop-down list that either includes the sensor you need to view or to
which the external sensor that you need to view is connected.
3. From the Sensors drop-down list, select a sensor for which data will be graphed. Only sensors
that are available on the device selected from the Pods drop-down list, and that are included in
the selected sensor set (if applicable) are listed in the Sensors drop-down list.
4. Use Start Time and End Time to specify the range of time for which sensor data is graphed, and
use the Refresh Interval drop-down list to specify how often the graph content is updated. The
default Start Time is 60 minutes and the default End Time is Present.
For more information, see “Capture settings” (for camera pods and CCTV adapter pods) or “Settings”
(for sensor pods).
28NetBotz Appliance User’s Guide
Viewing Historical Data
The History View lets you view and export historical data from one or more sensors. You can specify
which pods and sensors to include, as well as the range of time for which data will be retrieved. The data
can then be exported to a text file in a tab-delimited, comma-delimited, or semi-colon-delimited format.
The History View button is available on the Action/Information pane.
Running a historical data report
To define the parameters for the report:
1. Click History View on the Action/Information pane. The History View pane is displayed.
2. In the list of Pods, select one or more pods. Use Control-click or Shift-click to select multiple
pods. The Sensor list is populated with the sensors from the selected pods.
Note: Unplugged sensors will be displayed in the list, as will sensors with no
recorded data. Sensors that have been deleted from the system will not be shown.
3. In the list of Sensors, select one or more sensors. Use Control-click or Shift-click to select
multiple sensors.
4. In the Start time drop-down, select the amount of time for which you wish to display data.
5. Click Run History to run the report. Depending on the pods and sensors chosen, the report may
take a few minutes to complete for larger reports.
Note: Best results can be achieved by separating large report requests into logical
sections.
The report returns a sortable table with the pod name, sensor name, time the value was recorded, and the
value of the sensor. By default, the table is sorted by pod and sensor, with the most recent data listed first.
Only changes in value or state are listed in the table, so if a sensor has not changed during the report
scope, only the initial value will be listed. If a sensor has been disconnected during the entire scope of the
report, a empty table will be listed for that sensor.
Exporting the data to a text file
Once a report has been run, the displayed data can be exported into a text file. The file can be tab-
delimited, comma-delimited, or semi-colon-delimited.
Note: The Date column is exported in a 13-digit format (milliseconds since January 1st, 1970).
To export the data from a report:
1. On the History view, click Export Data.
2. Choose the delimiter for the file on the right side of the window. There are three choices,
Semicolon, Comma, and Tab.
3. Choose the location where you will save the file and enter a filename. Click Save.
29NetBotz Appliance User’s Guide
Event Log
The event log records System and Rack Access System events in order to provide an audit trail for
security-related events. The Event Log can hold ten pages of data (with each page limited to 64K of
data).
For each event, the date and time of the event is recorded, along with the category of the event, the
severity of the event, and a text description of the event.
To refresh the contents of the Event Log, click Refresh. Any new events will be appended to the bottom
of the current page.
To clear the current Event Log, click Clear. All recorded event data currently contained in the Event Log
is deleted. After the Event Log has been cleared, the first entry in the new log will be “Event log has been
cleared”.
30NetBotz Appliance User’s Guide
Advanced View: Pod/Sensor Settings
Use the icons in the Pod/Sensors Settings area of the Configuration view to configure the pods and
sensors connected to your appliance and configure the alert actions and policies that are used when alerts
are reported by sensors.
Note: The icons that appear in the Pod/Sensor Settings area depend on how your system is
configured. It is possible that not all icons discussed in this chapter will appear in your Pod/
Sensor Settings area.
Alert Action
Use the Alert Action icon to define Alert Actions.
Pre-configured alert actions
Your appliance comes with pre-configured alert actions. To use the pre-configured alert actions, edit the
alert action to provide the information that is required to complete the alert action.
Available alert notification methods
An alert action consists of a single alert notification method and any specific information necessary to
deliver the notification. Your appliance supports the following alert notification methods:
• Activate Button Output: Generates an output relay that is defined as a Button Relay.
Note: This alert notification method is designed for use only with output switch
devices.
• Call Web Services Alert Receiver: Sends alert data to a web server implementing the NetBotz
Web Services Alert Receiver.
• Play Audio Alert: Plays a description of the alert in spoken English.
• Play Custom Audio Alert: Plays a user-specified audio clip. Audio clips are uploaded to the
appliance using the Custom Audio Clip icon.
For information about Custom Audio Clips, see “Custom Audio Clips” on page 75.
• Send Custom HTTP GET: Delivers alert notifications as custom HTTP GET commands. The
URL generated from the alert action is user-definable, and can include BotzWare macro values.
• Send Custom Text File to FTP Server: Sends a customized text file with user-specified content
to an FTP server. Use macros supported by BotzWare to define the name of the directory on the
server in which custom text files are stored and the base filename used for the text files.
• Send Data to FTP Server: Sends an alert notification with information about the alert to an FTP
server. Use macros supported by BotzWare to define the name of the directory on the server in
which data files are stored and the base filename used for FTP data files.
• Send E-mail: Sends an alert notification e-mail with information about the alert to one or more
e-mail recipients. The alert notification e-mail can include images captured by a camera pod, a
graph, and a map of the sensor-specific data associated with the alert.
31NetBotz Appliance User’s Guide
• Send HTTP Post: Sends an HTTP post to a specified HTTP server with information about the
alert. The alert notification post can include images captured by a camera pod, a graph, and a map
of the sensor-specific data associated with the alert.
Note: The appliance posts all data according to the HTTP Post/FTP Data Delivery
parameters. You must configure the target HTTP server appropriately to receive the
posted data. More information can be found on the APC Web site.
• Send Short Message E-mail: Sends a user-configurable e-mail alert notification for devices with
limited display capabilities, such as cellular telephones and personal data assistants (PDAs). Use
macros supported by BotzWare to specify the contents of the title and body of the e-mail.
For more information on macros supported by BotzWare, see “BotzWare Macros” on
page 136.
• Send SNMP v1 Trap: Sends an SNMP trap that contains information about the alert to a
specified SNMP trap recipient.
• Send SNMP v3 Inform: Sends an SNMP INFORM packet that contains information about the
alert to a specified SNMP trap recipient.
• Send Wireless SMS Message: Sends a wireless SMS message that contains information about
the alert to an e-mail address or phone number.
For more information, see “SMS” on page 100.
• Set Beacon Output State: Set the Beacon to turn on or off in response to an alert.
• Set Output Switch 1: Set an output device to turn on or off in response to an alert.
• Set Output Switch 2: Set an output device to turn on or off in response to an alert.
Note: Set Output Switch 1 and 2 are only available on the NetBotz Rack Monitor 450,
550 and 570 models.
• Set Switch Output State: Generates an output relay that is defined as a Switch Relay.
Note: This alert notification method is designed for use only with relay output
devices.
• Set Lock Output State: Set the lock to lock or unlock in response to an alert.
• Set Outlet State: Set the outlet to turn on or off in response to an alert.
• Set Reader Output State: Set the card reader to enabled or disabled in response to an alert.
32NetBotz Appliance User’s Guide
Creating or editing alert actions
To create a new Alert Action or edit an existing Alert Action:
1. Double-click the Alert Actions icon.
2. Click Add... If you are editing an existing alert action, select it from Alert Action, click Edit,
and proceed to step 4 .
3. Select the alert notification method for this action from the Add Alert Action window, and click
OK.
4. Specify the notification information for this alert action.
For detailed notification method-specific instructions, see “Advanced View: Creating
Alert Actions” on page 118.
5. Click OK to save your changes. The saved alert action appears in the list of defined alert actions,
and is available for use in your Alert Profile.
If you create an Alert Action for a specific pod and subsequently remove and delete that pod from your
appliance, you must manually remove the alert actions that were associated with that pod.
Alert Profile
Use the Alert Profile icon to customize your appliance default alert notification policy, or to create
additional alert notification policies. Alert policies define the notification actions taken by the appliance
in response to alerts. Each Alert Profile consists of one or more Alert Sequences. An Alert Sequence
specifies:
• The period of time that must pass before an alert condition results in notification
• The number of times the notification is repeated if the alert condition is not corrected
• The time interval at which the notification is enacted
• One or more alert actions that are part of the Alert Sequence notification process
• The schedule that determines whether the Alert Sequence is active at the date and time the alert
occurs
• Capture settings that can override specific alert-action attributes, such as including graphs or
image captures with alert notifications
You can also use the Alert Profile icon to temporarily disable all alert notifications globally associated
with an Alert Profile.
33NetBotz Appliance User’s Guide
Default alert profile
Your appliance comes pre-configured with a default alert profile. The default policy features the
following four pre-configured Alert Sequences which are active 24 hours a day, 7 days a week:
• Alert Level 1: Begins immediately after an alert condition occurs (Start Value of 0) and repeats
two times at 5 minute intervals. It initiates the Primary E-Mail Notification, and Short Message
E-Mail alert actions.
• Alert Level 2: Begins 20 minutes after an alert condition occurs and repeats one time at a 10
minute interval. It initiates the Secondary E-Mail Notification and Short Message E-Mail alert
actions.
• Alert Level 3: Begins 90 minutes after an alert condition occurs and repeats two times at 60
minute intervals. It initiates the Primary E-Mail Notification, Secondary E-Mail Notification, and
Short Message E-Mail alert actions.
• Continuous Alert: Begins immediately after an alert condition occurs (Start Value of 0) and
repeats indefinitely at one minute intervals. It initiates the Send SNMP Trap alert action.
Note: Pre-defined alert actions or individual sensor thresholds may require additional
information such as e-mail addresses, server IP addresses, output devices, etc., for
notifications to be delivered. Be sure to properly configure alert actions and thresholds
used in your Alert Profile.
The default alert profile can be edited but not removed. When sensor thresholds are created, the default
alert profile is used unless you use advanced threshold settings to specify otherwise. You can also create
additional Alert Profiles.
Creating or editing an alert profile
To create a new alert profile or modify an existing alert profile:
1. Double-click the Alert Profile icon.
2. Click Add....
3. Type a label for the Alert Profile and configure the Alert Sequence(s) for the new profile.
For information on creating an Alert Sequence, see “Creating an alert sequence” on
page 34.
4. Click the Advanced tab to schedule an alert notification delay, if desired.
5. If you are modifying an existing alert profile, select the alert profile from the Profile table and
click Edit.... When you finish making your changes, click OK.
35NetBotz Appliance User’s Guide
Suppressing alert notifications
You can temporarily suppress all alert notifications associated with a selected alert profile globally.
Note: Disabling alert notifications prevents your appliance from automatically notifying you
of conditions that may be hazardous to your critical assets and spaces. Use this feature only for
scheduled maintenance or downtime.
When alert notifications are disabled, sensors in the Sensor Readings pane continue to turn red
to indicate that a threshold has been violated.
Disable Alert Notification settings are not persistently stored on the appliance.
If the appliance loses power or restarts prior to the specified time that alert notifications should
resume, alert notifications are no longer suspended.
To suppress alert notifications:
1. Select the Alert Profile for which you need to suppress alert notifications from the Alert Profile
window and click Edit....
2. Select the Advanced tab.
3. Check Suppress alert notifications until.
4. Use the calendar control to specify the date and time to resume alert notification.
5. Click OK.
36NetBotz Appliance User’s Guide
Camera Pods
To configure a camera:
Note: From the Navigation pane, you can right-click a Pelco camera and select Connect to...
to launch the Pelco Web interface for the camera. This will allow access to additional required
configuration settings.
1. For integrated cameras or cameras connected to the appliance, double-click the Camera Pods
icon. The Camera Pod Configuration window appears with a list of cameras.
2. For IP cameras that are shared, for example Pelco cameras, double-click the Shared Cameras
icon. The Shared Camera Configuration window appears listing the IP camera.
For more information on shared cameras, see “Pod, Pelco Camera, and Rack Access
PX-HID Sharing” on page 93.
3. From the window that appeared, select the camera to configure, then configure the camera by
using the buttons described below and in greater detail on the following pages:
– Click Settings to specify labels for the camera, to specify an interactive camera frame rate
limit and interactive camera mode limit.
– Click Capture to configure the camera image capture settings.
– Click Masking to configure the camera motion sensor and to specify motion and block-out
masks, if available.
– Click Visual Modes to specify the imaging mode and to specify the window to use with Pan
and Scan mode. (Not available for Pelco PTZ IP cameras.)
– Click Sensors to configure the sensors associated with the camera and to create thresholds for
those sensors.
Settings
Select a camera from the Camera Pods window and click Settings to open the Camera Pods Settings
window. From this window you can configure the following camera settings.
Note: Fields displayed may vary depending on the features of the camera selected.
Field Description
Pod Label The label that identifies the device. This field does not appear for
integrated cameras. For integrated cameras the Pod Label is set for
the appliance.
For more information, see “Settings” on page 69.
Camera Label An additional label for the camera. If you provide both a Pod Label
and a Camera Label, images and alerts generated by this device are
identified as Pod Label (Camera Label).
Microphone Label An additional label for the microphone on this pod (camera pods
and CCTV adapter pods only).
38NetBotz Appliance User’s Guide
Associating relays, switches, or outlets with integrated cameras and camera pods.
Relays, switches, and outlets can be associated with cameras to simplify manually changing relay states
from the Camera View.
Once a relay, switch, or outlet is associated with a camera, you can associate an action with it, and
manually generate that action from the camera image in the Camera View. You right-click the camera
image, and select the action from the menu. You can also configure Advanced View to include a button
on the camera image to generate the action. This applies to integrated cameras and cameras connected to
the appliance, but not shared IP cameras.
To associate a relay or switch with a camera, and include buttons in the Camera View for the associated
relays:
1. Double-click the Camera Pods icon.
2. A list of integrated cameras and cameras connected to the appliance appears. Select the camera
you want to configure.
3. Click Settings. Select the Associated Sensors tab.
4. Select one or more relays, switches, or outlets from Available Sensors to associate with the
selected camera. Click -> (right arrow) to move the selected relays to Selected Sensors. To
remove a sensor from the list, select one or more relays from Selected Sensors, and click <- (left
arrow) to move the selected sensor to Available Sensors.
5. To include buttons for the associated relay actions in the Camera View, check Overlay Buttons
on Camera Image.
6. Select the location in the camera image to place the associated relay action buttons.
7. Click OK.
Capture settings
Select a camera from the Camera Pods window and click Capture to open the Camera Capture
Settings window. From this window you can configure the following settings:
Note: Fields displayed may vary depending on the features of the camera selected.
Field Description
Brightness The brightness of the image captured by the camera, from 0 to 255.
Gamma correction Adjust the overall brightness of the camera image. Images not
properly corrected can look either bleached out or too dark.
Video format The format in which video is transmitted by the video source.
Note: This option is available only when configuring Capture
settings for CCTV adapter pods.
Rotate camera image 180 degrees Rotate the image captured by the camera 180 degrees.
Note: This option is not available when configuring Capture
settings for CCTV adapter pods.
39NetBotz Appliance User’s Guide
Flicker filter Minimize image brightness flickering that can occur in the dark
areas of the image.
Note: Enabling the flicker filter can impact the number of frames
per second at which images are captured and displayed, typically
noticeable only at image capture rates more than 5 per second.
Note: This option is available only when configuring Capture
settings for NetBotz Camera Pod 120s, Revision A0, Submodel
120-0000 or earlier. For revision and submodel details, click the
About button to open the About View.
Timestamp Set the location of the timestamp on the image capture.
Color Balance / Type of Lighting /
Red Balance / Blue Balance
The color balance settings used by the camera:
• Fluorescent: Best for locations with fluorescent lighting.
• Incandescent: Best for locations with incandescent lighting.
• Daylight: Best for locations with natural lighting.
• Auto-detect: Analyzes the lighting conditions and automatically
selects the best setting.
Select Custom to specify Red Balance and Blue Balance.
Mode The resolution of images captured for alert notifications. This
setting does not affect the image resolution displayed in the Camera
View.
Maximum Rate The maximum rate at which images are captured when a picture
alert is generated. This does not affect the image refresh rate
displayed in the Cameras View.
Image Quality The amount of compression applied to captured images. As
compression increases, file sizes decrease but the quality of the
image decreases as well. For Pelco cameras, this field does not
apply. Default is shown in this field and it cannot be changed.
Note: The image quality and the mode setting specified in the
Camera view affect the maximum frame rate available. Choosing a
low image quality and a small image size (mode), for example, will
result in a higher available maximum frame rate.
For more information, see “Standard camera controls” on page 21.
For more information on the Mode setting in the Camera view, see
“Viewing Live Video” on page 21.
Field Description
40NetBotz Appliance User’s Guide
Type the values in the appropriate fields. To see an example of an image capture using the updated
settings, click Apply. The sample image in the Capture window is updated using the new values. When
you are finished, click OK.
Post-Alert Capture Time The total number of seconds after the alert generating event that
images are included in alert notifications.
NOTE: For Pelco cameras, once an alert is generated a new alert
will not be generated until 30 seconds has elapsed. To ensure that
you capture all motion, set this field to 30 seconds.
The number of post-alert images captured is equal to the Post-Alert
Capture Time multiplied by the Maximum Rate. If the total number
of post-alert image captures and pre-alert image captures is larger
than the Maximum Camera Pictures setting for an alert action, the
most recent images captured are given preference and included in
the alert notification.
For more information, see “Creating a send e-mail alert action” on
page 126.
Pre-Alert Capture Time The total number of seconds prior to the event that generated the
alert that images are included in the alert notification. The number
of pre-alert images that are captured is equal to the Pre-Alert
Capture Time multiplied by the Maximum Rate.
If the total number of post-alert image captures and pre-alert image
captures is larger than the Maximum Camera Pictures setting for an
alert action, the most recent images captured are given preference
and included in the alert notification.
For more information, see “Creating a send e-mail alert action” on
page 126.
Delay Time Before Capturing The number of seconds between when an alert is generated and the
first picture capture.
Include Audio Specify whether the camera pod should capture audio and include it
with the alert.
NOTE: This option is available only when configuring Capture
settings for camera pods and CCTV Adapter Pods connected to a
NetBotz 550, NetBotz 570 or an appliance with the Advanced
Software Pack.
Audio Volume The volume at which audio is captured.
Capture Data Summary Shows information about the files generated by the pod using the
Capture settings. This information updates automatically as new
settings are specified.
Field Description
41NetBotz Appliance User’s Guide
Mask settings
Select a camera from the Camera Pods window and click Masking. Masking is available only on the
NetBotz Rack Monitor 570, 550 or on appliances for which the Advanced Software Pack has been
purchased. For more information, contact your NetBotz authorized reseller or the NetBotz support team.
Camera-based motion sensing compares concurrent image captures and determines whether any detected
changes are significant enough to generate an alert. An alert is generated only if observed changes meet
the criteria specified by both the Sensitivity and Area of Motion settings.
For Pelco cameras, custom settings are available to set the Sensitivity and Area of Motion more
precisely. Setting these values too high or too low can produce constant motion detection alerts, or no
alerts, depending on the camera.
Note: If you have the Advanced Software Pack installed, this window also features a Block
Out Mask tab.
Motion mask tab. The following controls are available:
To unmask a masked region, click and drag in the image to draw a box around the region you want to
unmask. Click Unmask Selection to remove the mask from the selected region. Red Xs displayed in the
selected region are removed.
Field Description
Enable Camera Motion Check to enable the camera motion sensor.
For Pelco cameras, the camera motion sensor is enabled by default.
Sensitivity Specifies how much change in a portion of the image capture is
tolerated before the change is considered movement. Lower values
indicate higher sensitivity and less tolerance for change between
images.
For Pelco cameras, an additional custom setting is available to set
the Sensitivity % to a value from 1 - 100.
Show outline of detected motion When enabled, any region of an image that indicates motion is
surrounded by a dotted-line outline. This feature is not available
with Pelco cameras.
Area of Motion Specifies how large an area of the image capture must change
(based on the Sensitivity value) before the change is considered
movement. Lower Area of Motion values indicate higher sensitivity
and smaller areas.
For Pelco cameras, an additional custom setting is available to set
the Area of Motion to a number of16x16 pixel blocks from 1 - 100.
Motion Detection Mask Specify regions of the image to be ignored by the Camera Motion
sensor.
To mask a portion of the image, click and drag to draw a box around
the region to ignore. Click Mask Selection. Red Xs appear in the
region.
44NetBotz Appliance User’s Guide
Scanned Devices
Note: The Scanned Devices icon is only available with the purchase of the 5-node Scanner/
IPMI Pack. For more information, contact your NetBotz authorized reseller or the NetBotz
support team.
Scanned devices are SNMP targets that are monitored by the NetBotz appliance. You can monitor status
information for up to five remote SNMP targets such as servers, routers, and switches as well as APC
devices such as APC UPSs and APC Rack Power Distribution Units (PDUs). When you add SNMP
targets, each target appears in the Navigation pane. Once added, you can set thresholds, monitor alerts,
and graph reported data. For APC devices, at user-configurable intervals, the appliance retrieves sensor
information specific to the APC device. For all SNMP targets, the appliance monitors the following MIB
II SNMP values:
• Online: State sensor that reports whether the target is Online or Offline.
• Ping RTT: Analog sensor that reports the amount of time it takes SNMP queries or ICMP Ping
requests to complete a send and reply from the appliance.
• SNMP System Contact: Displays the target system contact data (does not support threshold
configuration).
• SNMP System Description: Displays the target system description data (does not support
threshold configuration).
• SNMP System Location: Displays the target system location data (does not support threshold
configuration).
• SNMP System Name: Displays the target system name data (does not support threshold
configuration).
• SNMP System Object ID: Displays the target system object ID data (does not support threshold
configuration).
• SNMP System Uptime: Analog sensor that reports the uptime value of the target.
• System Model: Displays the target system model data (does not support threshold configuration).
• System Type: Displays the target system type data (does not support threshold configuration).
• System Vendor: Displays the target system vendor data (does not support threshold
configuration).
49NetBotz Appliance User’s Guide
Sensor settings
Select an SNMP target from the SNMP Targets view and click Sensors to open the Sensor
Configuration window. Monitored values available from the SNMP target are listed in the Sensors list.
Select a sensor from the Sensors list to display thresholds defined for that sensor in the Thresholds
selection list.
Note: If the selected sensor does not support threshold configuration, a message advising
you of this appears in the Thresholds area of the interface.
To modify a sensor:
1. Select a sensor from the Sensors list.
2. Click Modify to open the Modify Sensor window.
3. Type a label in the Label field. This label can be up to 64 characters in length, and identifies the
sensor in the Sensor Data pane, Advanced View interfaces, and alert notifications.
4. From Sensor Value History, select the amount of time that data reported by this sensor is stored
on the appliance. The amount of data available on the appliance affects the maximum amount of
data that can be graphed.
For more information see “Viewing Graphs” on page 27.
5. Click OK to save your changes.
Threshold configuration. To configure a threshold, select a sensor from the Sensors selection list.
Previously configured thresholds for the selected sensor appear in the Thresholds selection list.
All sensors have a default threshold that is generated automatically by Advanced View. This threshold
provides the typical threshold for the specific sensor type. Thresholds can be customized.
Sensor thresholds are explained in detail in “Advanced View: Defining Thresholds” on
page 113.
To enable or modify a sensor threshold:
1. Select a sensor from the Sensor list.
2. Select the threshold to enable or modify from the Thresholds list.
3. Click Edit....
4. The Edit Threshold window appears.
– To enable the threshold, check Enabled.
– To change threshold settings, use the controls in the Edit Threshold window.
5. Click OK to save your new settings.
The controls available in the Edit Threshold window are determined by the type of
threshold that you create or edit. For detailed instructions on how to create or edit
thresholds, see “Advanced View: Defining Thresholds” on page 113.
54NetBotz Appliance User’s Guide
Output control external port settings
Select a device from the Output Control Configuration window and click External Ports. To modify
devices connected to your output control devices:
1. Select the output control action to assign to the corresponding port from Relay Output Type.
Note: Output control actions do not apply for devices wired between the NO and NC
terminals. These devices have an always open state.
The following output control actions are available when the output control device is wired
between the NO (Normally Open) and COM terminals on the appliance:
Action Description
None No output action is associated with this port.
One-Second Button
(NC)
When activated, a normally closed (NC) relay is switched to an
open state for 1 second, and then switched back to closed.
One-Second Button
(NO)
When activated, a normally open (NO) relay is switched to a
closed state for 1 second, and then switched back to open.
Switch (NC) When activated, a normally closed (NC) relay is switched to an
open state.
Switch (NO) When activated, a normally open (NO) relay is switched to a
closed state.
Ten-Second Button
(NC)
When activated, a normally closed (NC) relay is switched to an
open state for 10 seconds, and then switched back to closed.
Ten-Second Button
(NO)
When activated, a normally open (NO) relay is switched to a
closed state for 10 seconds, and then switched back to open.
Reboot Button When activated, power to the outlet is interrupted for 10 seconds,
and then restored.
Termékspecifikációk
| Márka: | NetBotz |
| Kategória: | Biztonság |
| Modell: | NBWL0456 |
Szüksége van segítségre?
Ha segítségre van szüksége NetBotz NBWL0456, tegyen fel kérdést alább, és más felhasználók válaszolnak Önnek
Útmutatók Biztonság NetBotz
24 Augusztus 2024
24 Augusztus 2024
24 Augusztus 2024
24 Augusztus 2024
24 Augusztus 2024
24 Augusztus 2024
24 Augusztus 2024
Útmutatók Biztonság
- Biztonság Nedis
- Biztonság Grundig
- Biztonság Bosch
- Biztonság Theben
- Biztonság Panasonic
- Biztonság Siemens
- Biztonság Medion
- Biztonság Geemarc
- Biztonság TRENDnet
- Biztonság EZVIZ
- Biztonság Technaxx
- Biztonság Eden
- Biztonság Hikvision
- Biztonság Netgear
- Biztonság Lamax
- Biztonság V-TAC
- Biztonság Doro
- Biztonság First Alert
- Biztonság Devolo
- Biztonság Powerfix
- Biztonság BaseTech
- Biztonság Edimax
- Biztonság Bavaria
- Biztonság Eufy
- Biztonság Overmax
- Biztonság Foscam
- Biztonság Alecto
- Biztonság Honeywell
- Biztonság Juwel
- Biztonság Velleman
- Biztonság Prestigio
- Biztonság Grandstream
- Biztonság Monacor
- Biztonság Blaupunkt
- Biztonság Easy Home
- Biztonság Elro
- Biztonság Abus
- Biztonság Trust
- Biztonság Marmitek
- Biztonság Fenton
- Biztonság Steinel
- Biztonság Trebs
- Biztonság Alphatronics
- Biztonság Velbus
- Biztonság Provision-ISR
- Biztonság Somfy
- Biztonság Axis
- Biztonság Optex
- Biztonság EasyMaxx
- Biztonság Smartwares
- Biztonság IGET
- Biztonság Kopp
- Biztonság Ajax
- Biztonság AngelEye
- Biztonság Aritech
- Biztonság AceSee
- Biztonság Brennenstuhl
- Biztonság Alhua - Dahua
- Biztonság Yale
- Biztonság Tevion
- Biztonság Eminent
- Biztonság Axa
- Biztonság Maginon
- Biztonság Profile
- Biztonság Marquant
- Biztonság Jacob Jensen
- Biztonság Ednet
- Biztonság Perel
- Biztonság ME
- Biztonság Goliath
- Biztonság Audiovox
- Biztonság Nest
- Biztonság Grothe
- Biztonság LevelOne
- Biztonság Unitron
- Biztonság Netatmo
- Biztonság Goobay
- Biztonság Switel
- Biztonság Bticino
- Biztonság Topcraft
- Biztonság Secure Pro
- Biztonság Sygonix
- Biztonság Nemef
- Biztonság Dahua
- Biztonság BRK
- Biztonság Hagenuk
- Biztonság Waeco
- Biztonság Logicom
- Biztonság Jupiter Pro
- Biztonság Xavax
- Biztonság Elkron
- Biztonság Orbis
- Biztonság Niko
- Biztonság Gira
- Biztonság Jung
- Biztonság Interlogix
- Biztonság Dnt
- Biztonság Fito
- Biztonság Urmet
- Biztonság Ranex
- Biztonság Wanscam
- Biztonság Satel
- Biztonság Dymond
- Biztonság Notifier
- Biztonság Friedland
- Biztonság HomeWizard
- Biztonság Plustek
- Biztonság Golmar
- Biztonság Batavia
- Biztonság Storage Options
- Biztonság NetworX
- Biztonság Bitron Video
- Biztonság Zmodo
- Biztonság Elro-Flamingo
- Biztonság Electronics Line
- Biztonság One2track
- Biztonság HUMANTECHNIK
- Biztonság PIR Alarm
- Biztonság Heidemann
- Biztonság Directed Electronics
- Biztonság Oplink
- Biztonság BML
- Biztonság Unitec
- Biztonság Jablotron
- Biztonság Muller
- Biztonság Home8
- Biztonság AVTech - Velleman
- Biztonság Galaxy
- Biztonság Sonic Alert
- Biztonság I-onik
- Biztonság Smartalarm
- Biztonság GE Security
- Biztonság Microtech
- Biztonság Nor-tec
- Biztonság Entrya
- Biztonság Tegui
- Biztonság Stobo
- Biztonság Kompernass
- Biztonság Iiquu
- Biztonság Storex
- Biztonság Powermax
- Biztonság Woonveilig
- Biztonság Mikros
- Biztonság Bolyguard
- Biztonság Indexa
- Biztonság Skytronic
- Biztonság Paradox
- Biztonság Flamingo FA15RF
- Biztonság SecuFirst
- Biztonság BRK DICON
- Biztonság FBII
- Biztonság FlinQ
- Biztonság Dericam
- Biztonság Myfox
- Biztonság Kocom
- Biztonság RISCO Group
- Biztonság SmartHome
- Biztonság Bellman
- Biztonság Protector
- Biztonság I-Tel
- Biztonság Home Protector
- Biztonság Ksenia
- Biztonság Mr Safe
- Biztonság Epine
- Biztonság Inner Range
- Biztonság Dedicated Micros
- Biztonság Visonic
- Biztonság PROmax
- Biztonság Y-cam
- Biztonság Selvag
- Biztonság Voxx
- Biztonság Fracarro
- Biztonság Guardall
- Biztonság Xena
- Biztonság Smanos
- Biztonság One Concept
- Biztonság QuattSecure
- Biztonság Securitas
Legújabb útmutatók Biztonság
16 Január 2025
15 Január 2025
15 Január 2025
12 Január 2025
11 Január 2025
5 Október 2024
23 Szeptember 2024
23 Szeptember 2024
23 Szeptember 2024
22 Szeptember 2024