Használati útmutató Muse M-32CM

Muse hangszóró M-32CM

Olvassa el alább 📖 a magyar nyelvű használati útmutatót Muse M-32CM (2 oldal) a hangszóró kategóriában. Ezt az útmutatót 2 ember találta hasznosnak és 2 felhasználó értékelte átlagosan 4.5 csillagra

Letöltés PDF
Oldal 1/2
AUX IN
1. Plug one end of cable (not included)
into the AUX IN socket (15) on the unit.
2. Plug the other end of the cable into the
Headphone or Line Out socket of the
external source.
GB - 2
POWER SUPPLY
2. The remote control unit operates on 2pcs
“AAA/UM4” battery (excluded). To
power up the remote control, open the
battery door, install the battery
according to the polarity diagram on the
battery compartment, then close the
battery door.
Before throwing any batteries away, consult your distributor who may be able
to take them back for specific recycling.
Important note
If an abnormal display indication or an operating problem occurs, disconnect the AC
power cord. Wait at least 5 seconds, then reconnect the AC power cord.
3. Press the STOP / FUNCTION
button (20) on the unit or the FUNCTION
button
(H1) on the remote control to select Auxiliary function. “AUX” indicator shows on
the display.
1. This micro system operates on AC230V~50Hz line power supply.
An external (auxiliary) audio source (i.e., personal CD player or MP3 player) can be
connected to this unit and heard through the speakers.
Installing Battery
Insert 2 “AAA/ UM4” batteries to the remote control prior to use. Make sure to match
their polarities (+/-) to the markings inside the compartment.
NOTES:
- In order to avoid leakage, always remove the batteries when unit will not be used for
a long period of time.
- If the remote control is not going to be used for a long time, remove the battery to
avoid damage caused by battery leakage corrosion. -
CAUTION: Danger of explosion if battery is incorrectly replaced. Replace only with
the same or equivalent type.
Track number “01” ,“CD”& the symbol “ ” will be shown during
normal compact disc playback.
Track number “001”,“CD”, the symbol “ ” & “MP3”will be shown during MP3 playback.
Track number “001”,“MP3”, the symbol “ ” & “USB” will be shown during USB
playback.
During Repeat 1
mode, display shows
During Repeat all
mode, display shows
During Random mode,
display shows
FOR NORMAL COMPACT
DISC PLAYBACK
To: PRESS:
Stop play
Pause play once
Resume play after pause again
Scan forward and backward and hold /
Skip tracks /
Repeat current track PLAY MODE once
Repeat all tracks PLAY MODE twice
Random play PLAY MODE three times
DISC ERROR
Note: If the disc is dirty, damaged or unreadable, or if the disc is placed upside down,
the “ ” indicator will appear on the display. If this occurs, clean the disc, insert the
disc correctly, or try another disc.
REPEAT, REPEAT FOLDER AND RANDOM PLAYBACK
Press PLAY MODE button (12) during unit ON mode.
CD plays with a single track repeat, all tracks repeat or
randomly.
FOR MP3/USB PLAYBACK
During Repeat 1
mode, display shows
During Repeat folder
mode,display shows
During Repeat all
mode, display shows
During Random mode,
display shows
RANDOM
GB -5
M-32CM
MICRO SYSTEM CD/MP3/USB
User Manual
Please read the instruction carefully
before operating the unit.
English GB - 1
LOCATION OF CONTROLS
REMOTE CONTROL
STANDBY BUTTON
PLAY/PAUSE BUTTON
F - SKIP BUTTON
+ 10 TRACK BUTTON
FOLDER UP BUTTON
PLAY MODE BUTTTON
MUTE BUTTON
VOLUME BUTTON
SPEAKER
POWER / STANDBY BUTTON
CD DOOR
REMOTE SENSOR
LCD DISPLAY
USB PORT
CD OPEN / CLOSE BUTTON
FM STEREO LED INDICATOR
PLAY / PAUSE BUTTON
VOL + BUTTON
F - SKIP / UP BUTTON
PLAY MODE BUTTON
FOLDER UP BUTTON
PROGRAM / CLOCK - ADJ.
BUTTON
AUX. IN JACK
PHONES JACK
BAND BUTTON
B - SKIP / DN BUTTON
VOL - BUTTON
STOP / CLEAR / FUNCTION
BUTTON
TUNING CONTROL
SPEAKER CORD
LEFT SPEAKER JACK
AC POWER CORD
RIGHT SPEAKER JACK
FM WIRE ANTENNA
FUNCTION BUTTON
STOP BUTTON
B - SKIP BUTTON
- 10 TRACK BUTTON
FOLDER DOWN BUTTON
PROGRAM/CLOCK-ADJ
BUTTON
BAND BUTTON
VOLUME BUTTON
H1.
H2.
H3.
H4.
H5.
H6.
H7.
H8.
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
15.
16.
17.
18.
19.
20.
21.
22.
23.
24.
25.
26.
H9.
H10.
H11.
H12.
H13.
H14.
H15.
H16.
Press MUTE button (H15) to on/off mute function.
Note: The mute on is cancelled when:
a. The power is off/on
b. The Volume is adjusted by the VOL +/- button.
USING HEADPHONES (Headphones Not Included)
Connect a set of stereo headphones with 3.5mm mini plug to the phone jack on the
bottom panel. The speakers are automatically cut off when headphones are in use.
Note: To establish a safe headphones sound level:
Start your volume control at a low setting.
Slowly increase the sound until you can hear it comfortably and clearly, and without
distortion.
1. The player is on/off by pressing STANDBY (2/H9) button.
2. The function is selected cyclically by pressing
STOP / CLEAR / FUNCTION button:
CD USB TUNER AUX
Press STANDBY button (2/H9) to turn on the unit,
then press VOLUME +/- control (10/H16, 19/H8)
to adjust the sound to comfortable level. The vol-
ume level will show on display for a few seconds.
GB - 3
AUDI O CONTROL
ADJUSTING THE SOUND
In full power, the continuous listening of the player may damage the user’s
hearing.
MUTE
To cut off the sound from the speakers temporarily, press the MUTE button (H15).
The Volume level icon flash on the LCD display (5). Press the MUTE button again to
cancel Mute mode and restore the sound from the speakers.
NOTE: When standby light is lit, unit is in OFF (standby) mode.
TO ADJUST THE VOLUME
VOLUME
VOL - VOL +
1. Press STANDBY button (2/H9).
2. Press the STOP / FUNCTION button to select CD.
3. Open the CD door(3) by pushing the CD door Open button (7).
4. Place the CD with label side up inside the CD compartment
and close the CD door (3).
5. After a few seconds, the total number of tracks and total
playing time will appear on the Multifunction display (5).
Press button (9/H10) to start playing the CD.
6. Press the PLAY/PAUSE button.
1. Turn on the unit by pressing STANDBY
button (2/H9).
2. Press the STOP (20/H2) /FUNCTION
(20/H1) button to select the tuner.
3. Press the BAND button (17/H7) to select desired band.
4. Tune to the desired radio station by using TUNING knob (21) and frequency is displayed.
5. Adjust the sound.
The clock is displayed on LCD display at standby mode.
1. Press the PROGRAM / CLOCK-ADJ.
button (14/H6).
2. Press the F-SKIP/UP (11/H11) or
B-SKIP /DOWN (18/H3) to select 12 hours
or 24 hours display.
3. Press the PROGRAM / CLOCK-ADJ. button
(14/H6), the hour digit flash.
4. Press the F-SKIP/UP (11/H11) or B-SKIP/DOWN
(18/H3) to adjust hour digit.
5. Press the PROGRAM / CLOCK-ADJ. button (14/H6), the minute digit flash.
6. Press the F-SKIP/UP (11/H11) or B-SKIP/DOWN (18/H3) to adjust
minute digit.
7. Press the PROGRAM / CLOCK-ADJ. button (14/H6) again, the correct time is
shown on display.
CLOCK SETTING
LISTENING TO THE RADIO
COMPACT DISC OPERATION
GB - 4
ANTENNA
For FM reception fully unwind the external FM wire antenna and adjust direction, for
optimum reception.
AFTER LISTENING
Turn off the unit by pressing STANDBY button (2/H9).
　　　　　2009-6-15, 10:271
FOR MP3 PLAYBACK
Programmed playback enables folders/albums or tracks on a disc to be played in the
desired order. Up to 20 folders/albums or tracks can be programmed.
1. Press the “PROGRAM/CLOCK-ADJ.” button (14/H6).
2. Press the FOLDER DOWN (H5) /FOLDER UP (13/H13) button to select the
desired folder.
3. Press the / buttons to select the desired track number.
4. Press “PROGRAM/CLOCK-ADJ.” button (14/H6) again to memorize the track.
5. Repeat steps 2 to 4 until all desired tracks are programmed.
6. Press the “PLAY/PAUSE” button (9/H10) to start.
“PROGRAM” is shown on the CD display.
7. Press “STOP/FUNCTION” button to stop programmed playback.
8. Press “PLAY/PAUSE” button (9/H10) to resume programmed playback.
9. Press “STOP/FUNCTION” button again until “PROGRAM” disappear from
the display or turn off the CD player can clear the programmed memory.
Note : Programming can only be made when the player is in stop mode.
GB - 6
NOTE ON CD-R/RW DISCS
- CD-Rs or CD-RWs playback capability at this player may vary depending on quality
of media, CD-Burner, speed of burning and application software. Because of non
standardized format definition/production of CD-R/RW, playback-quality and
performance are not guaranteed.
- Manufacturer is not responsible for the playability of CD-R/RW due to recording
conditions such as PC performance, writing software, media ability, etc.
- Do not attach a seal or label to either side of the CD-R/RW disc. It may cause a
malfunction.
- Do not use your set immediately after transport from a cold place to a warm place,
there may be condensation problems.
FOLDER UP / DOWN
- Press FOLDER UP (13/H13) or FOLDER DOWN
(H5) button to select desired folder.
- Press B-SKIP/DOWN button (18/H3) or
F-SKIP/UP button (11/H11) to select desired track.
- Press PLAY/PAUSE button (9/H10) to start playing.
+10 / -10 BUTTON
These buttons allow you to advance 10 tracks at a time (+10) or go back 10 tracks at a
time (-10).
PROGRAM PLAYBACK
FOR NORMAL COMPACT DISC PLAYBACK
Programmed playback enables tracks on a disc to be played in the desired order. Up
to 20 tracks can be programmed.
-10 BUTTON
Same as +10 button (see above) except you can go back 10 tracks at a time. For
example, if Track 12 is playing and -10 is pressed, it will take you back to Track 2 (12-
10 = 2). You may also press -10 (H4) repeatedly (as above) to go back 10 tracks each
time -10 is pressed. If there are less than 10 tracks available, CD will go to the last
possible track.
+10 BUTTON
For example, if Track 1 is playing and +10 is pressed, it will take you to Track 11
(1+10 = 11). You may press +10 (13/H12) repeatedly to advance forward 10 tracks at
a time. (For example, when on Track 1, press once to Track 11 (1+10 = 11). Press
again to Track 21 (11+10 = 21).) If there are less than 10 higher tracks available, CD
will go back to Track 1.
1. Press the “PROGRAM/CLOCK-ADJ.” button (14/H6).
2. Press the / buttons to select the desired track number.
3. Press “PROGRAM/CLOCK-ADJ.” button (14/H6) again to memorize the track.
4. Repeat steps 2 and 3 until all desired tracks are programmed.
5. Press the “PLAY/PAUSE” button (9/H10) to start.
“PROGRAM” is shown on the CD display.
6. Press “STOP/FUNCTION” button to stop programmed playback.
7. Press “PLAY/PAUSE” buttons (9/H10) to resume programmed playback.
8. Press “STOP/FUNCTION” button again until “PROGRAM” disappear from the
display or turn off the CD player can clear the programmed memory.
USB OPERATION
1. Connect USB stick or MP3 player into the USB port.
2. Press STOP / FUNCTION button (20) to select USB.
3. Press PLAY / PAUSE button (9/H10) to start playback.
Note:
- USB connector does not design for communication with computer directly.
- Manufacturer is not responsible for the playability of USB disk or MP3 player due to
recording condition, capacity, interface compatibility, etc.
- Due to different formats, some USB stick or MP3 players may take longer time to be
read.
- USB stick is direct connected or with a cable with max. 0.5m length.
GB -7
- Do not expose discs to direct sunlight, high humidity, high temperatures or dust,
etc. Prolonged exposure to extreme temperatures can warp the disc (such as
leaving the disc in your car during summertime).
- When cleaning the disc, wipe in straight lines from the center of the
disc to the outer edge of the disc. Never wipe in circular motions.
Note: Always press STOP button and wait for the disc stop rotating
before opening the CD door to remove the disc.
- If there is a scratch, dirt or fingerprint on the CD, it may cause
tracking error. Before playing, clean the CD with a cleaning cloth.
Wipe the CD from the center out. Don’t store discs in places with
high temperatures or high humidity-they can become warped.
After playing, store the CD in its cases.
GB - 8
CARE AND MAINTENANCE
1. Clean the unit with a soft, damp (never wet) cloth. Solvent or detergent should
never be used.
2. Avoid operating your unit under direct sunlight or in hot, humid or dusty places.
3. Keep your unit away from heating appliances and sources of electrical noise such
as fluorescent lamps or motors.
- Handle the disc only by its edges. Never allow your fingers to come in contact with
the shiny, unprinted side of the disc.
- Do not attach any tape, stickers, etc and/or write anything on either side of the disc.
- Clean the disc periodically with a soft, lint-free , dry cloth. Never use deter gents or
abrasive cleaners to clean the disc. If necessary, use a CD cleaning kit.
- If a disc skips or gets stuck on a section of the disc, it is probably dirty or damaged
(scratched).
- To remove a disc from its storage case,
press down on the center of the case
and lift the disc out, holding it carefully
by the edges. Discs should be stored
in their cases after use to avoid
scratches.
COMPACT DISC CARE
CLEANING THE LENS
A dirty lens will cause sound skipping. If the lens is very dirty, the player may not
work. We suggest using a special cleaning disk (not included) available in most
music and Hi-Fi stores. However, if you do not have one, you may use a cotton swab
very slightly dampened with alcohol to clean the lens.
GB - 9
CLEANING THE UNIT
- To prevent fire or shock hazard, disconnect your unit from the AC power source
when cleaning.
- If the cabinet becomes dusty, wipe it with a soft cloth. Do not use any wax or polish
sprays on the cabinet.
- If the cabinet becomes dirty or smudged with fingerprints it may be cleaned with a
soft cloth slightly dampened with a mild soap and water solution. Never use
abrasive cloths or polishes as there will mar the finish of your unit.
ATTENTION: To reduce the risk of electric shock, do not remove
the cover. There are no user serviceable parts inside the unit. Refer
all servicing to qualified personnel.
The lightening flash with arrowhead symbol within the triangle is a warning
sign alerting the user of “dangerous voltage” inside the unit.
The exclamation point within the triangle is a warning sign alerting the user of
important instructions accompanying the product.
CAUTION: Invisible laser radiation when open and interlocks defeated. Avoid
exposure to beam.
WARNING
WARNING - To reduce the risk of fire or electric shock, do not expose this appliance
to rain or moisture.
SPECIFICATIONS
RADIO SECTION
Tuning ranges:
Antennas:
GENERAL
Output power:
Power consumption:
Speaker:
Phone jack:
Power source:
DIMENSIONS
Main unit:
Speaker:
Weight:
FM 87.5-108MHz
MW522-1620kHz
MW Built - in ferrite bar
FM wire antenna
1W + 1W (RMS)
9W
3½’’ 8 OHM
3.5MM
AC:230V~50Hz
143(L) x 227(D) x 179(H)mm
101(L) x 193(D) x 174(H)mm
2.6KGS
PRECAUTIONS
IMPORTANT
- Do not throw batteries in fire
- Do not be exposed to dripping or splashing, and that no object filled with liquids,
such as vases, shall be placed on the apparatus.
- Mains plug is used as the disconnect device and it shall remain readily operable.To
be completely disconnected the power input, the mains plug of the apparatus shall
be disconnected from the mains completely.The mains plug should not be
obstructed OR should be easily accessed during intended use.
- Attention should be drawn to the environmental aspects of battery disposal.
- No naked flame sources such as lighted candles should be placed on the apparatus.
- The use of apparatus is only in moderate climates.
- See markings on bottom / back of the product.
- Excessive sound pressure from earphones and headphones can cause hearing loss.
- Battery shall not be exposed to excessive heat such as sunshine, fire or the like.
Heat- Do not use this unit near sources of heat, including heating vents, stoves, or
other appliances that generate heat.
Mounting surface- Place the unit on a flat, even surface.
Ventilation- The unit should be situated with a adequate space around it so that
proper heat ventilation is assured. Allow 10 cm (4 in.) clearance from the near and
the top of the unit and 5 cm (2 in.) from each side.
- Do not place the unit on a bed, rug, or similar surface that may block the ventilation
openings.
- Do not install the unit in a bookcase, cabinet, or airtight rack where ventilation may be
impeded.
Object and liquid entry- Take care that objects or liquids do not get inside the unit
through the ventilation openings.
Condensation- Moisture may form on the CD Pickup lens when:
- The unit is moved from a cold spot to a warm spot
- The heating system has just been turned on
- The unit is used in a very humid room
- The unit is cooled by an air conditioner
When this unit has condensation inside, it may not function normally. Should this
occur, leave the unit for a few hours,then try to operate again.
GB - 10
If at any time in the future you should need to dispose of this product please
note that Waste electrical products should not be disposed of with house-
hold waste. Please recycle where facilities exist. Check with your Local Au-
thority or retailer for recycling advice. (Waste Electrical and Electronic Equip-
ment Directive)
GB - 11
Electric Power
1 Power sources- Use AC house current, as specified in the Operating instructions
and marked on the unit.
2 AC power cord
- When disconnecting the AC power cord, pull it out by the AC power plug. Do not pull the
cord itself.
- Never handle the AC power plug with wet hands, as this could result in fire or
electric shock.
- Power cords should be firmly secured to avoid being bent, pinched, or walked upon.
Pay particular attention to the cord from the unit to the power socket.
- Avoid overloading AC power plug and extension cords, beyond their capacity, as
this could result in fire or electric shock.
3 When not in use - Unplug the AC power cord from the AC outlet if the unit will not
be used for several months or more. When the cord is plugged in a small amount of
current continues to flow to the unit, even when the power is turned off.
Electrical Fast Transient (Burst) / ESD Remark:
- In case of misfunction due to electrical fast transient (Burst) or electrostatic discharge, just
reset the product (reconnect of power source may be required) to resume normal operation.
　　　　　2009-6-15, 10:272

Termékspecifikációk

Márka: Muse
Kategória: hangszóró
Modell: M-32CM

Szüksége van segítségre?

Ha segítségre van szüksége Muse M-32CM, tegyen fel kérdést alább, és más felhasználók válaszolnak Önnek


Útmutatók hangszóró Muse

Muse

Muse MC-50 WI Útmutató

1 Április 2025
Muse

Muse M-780 LG Útmutató

1 Január 2025
Muse

Muse M-750 FBT Útmutató

31 December 2025
Muse

Muse M-1937 DJ Útmutató

5 December 2024
Muse

Muse M-785 BT Útmutató

5 December 2024
Muse

Muse M-970 BT Útmutató

5 December 2024
Muse

Muse M-1928 DJ Útmutató

11 Október 2024
Muse

Muse M-1982 DJ Útmutató

11 Október 2024
Muse

Muse M-930 DJN Útmutató

8 Október 2024
Muse

Muse M-1935 DJ Útmutató

28 Szeptember 2024

Útmutatók hangszóró

Legújabb útmutatók hangszóró

Celly

Celly Ultraboost Útmutató

1 Április 2025
QSC

QSC MD-FP152-124r Útmutató

30 Március 2025
QSC

QSC PL-CA6 Útmutató

30 Március 2025
QSC

QSC PL-SUB15 Útmutató

30 Március 2025
QSC

QSC PL-SUB10 Útmutató

30 Március 2025
QSC

QSC MD-FP152-64r Útmutató

30 Március 2025
QSC

QSC PL-SUB12 Útmutató

30 Március 2025
Audac

Audac ARCHI210 Útmutató

30 Március 2025
Audac

Audac ARCHI10 Útmutató

30 Március 2025
Prixton

Prixton Jaia Útmutató

30 Március 2025