Használati útmutató Micro Connect MC-GEN-270

Micro Connect kapcsoló MC-GEN-270

Olvassa el alább 📖 a magyar nyelvű használati útmutatót Micro Connect MC-GEN-270 (1 oldal) a kapcsoló kategóriában. Ezt az útmutatót 6 ember találta hasznosnak és 2 felhasználó értékelte átlagosan 4.5 csillagra

Letöltés PDF
Oldal 1/1
INTRODUCTION:
2 Way Speaker Switch
with Banana Connector
The product is used to distribute loudspeaker output signals from
audio amplifiers to different loudspeakers for selection and control
the volume.
This product is only approved for connection to loudspeaker outputs
of audio amplifiers and inputs of passive loudspeakers.
CONNECTION:
OPERATION:
SPECIFICATIONS:
PACKAGE CONTENTS:
● Main unit x1
● User Manual x1
1) Connect only loudspeaker outputs of audio amplifiers to the loudspeaker terminals AMP INPUT.
2) Connect only passive loudspeakers with impedance between 4 and 8 ohms to the loudspeaker terminals
SPEAKER OUTPUT.
3) Use only suitable speaker cables with a maximum cross-section of 6 mm² for cabling.
4) Carefully check the relevant operating instructions of the devices that are to be connected in regards to input and
output wiring.
5) If these instructions are not observed, the device or connected devices (amplifier or loudspeaker) may get
damaged.
6) Switch off the power switch of the amplifier before connecting it and do not switch the amplifier on again until you
have made all the necessary connections and che¬cked them. Proceed in the same way when changing the
circuit.
7) Make sure to introduce neatly the stranded wires into loudspeaker terminals to ex¬clude short circuits. Do not
remove more than 6 mm of insulation from the speaker line.
● Note the identification for connecting the loudspeaker terminals:
red = positive terminal
black = negative terminal
RIGHT = right terminal
LEFT = left terminal
● Connect loudspeaker terminals SPEAKER OUTPUT PAIR 1 and PAIR 2 to the speakers.
● Connect loudspeaker terminals AMP INPUT to the loudspeaker outputs of the amplifier.
Loudspeakers connected can be switched on individually or at the same time using the SPEAKERS selectors.
Speaker pair 1 is still running when both SPEAKERS selectors are in the OFF posi¬tion. This circuit protects your
amplifier against damage during idle operation.
● Turn on your amplifier and start the music programme you want.
● Use the SPEAKERS selectors to select the desired loudspeaker pair (PAIR 1 or PAIR 2).
Position ON > Loudspeaker pair switched on
Position OFF > Loudspeaker pair switched off
● The SPEAKER PAIR 2 VOLUME controller is used to adjust the volume of speaker pair 2.
● The overall volume is adjusted with the volume control on the amplifier.
Load.............................................. 60 W per channel
Impedance................................... 4 – 16 Ω
Cable length................................. max. 50 m
Wire cross section........................ max. 2.5 mm2
Operating conditions.................... -25 to +85 ºC, 20 – 75 % RH
Storage conditions....................... -25 to +85 ºC, 20 – 75 % RH

Termékspecifikációk

Márka: Micro Connect
Kategória: kapcsoló
Modell: MC-GEN-270

Szüksége van segítségre?

Ha segítségre van szüksége Micro Connect MC-GEN-270, tegyen fel kérdést alább, és más felhasználók válaszolnak Önnek


Útmutatók kapcsoló Micro Connect

Micro Connect

Micro Connect MC-GEN-270 Útmutató

30 Augusztus 2024
Micro Connect

Micro Connect MC-HM-MT402H Útmutató

18 Augusztus 2024
Micro Connect

Micro Connect MC-HM-MT404L Útmutató

17 Augusztus 2024

Útmutatók kapcsoló

Legújabb útmutatók kapcsoló

Hager

Hager LVS0060RPX Útmutató

12 December 2024
Hager

Hager HIB412M Útmutató

12 December 2024
Hager

Hager LVSR1VPVK4 Útmutató

12 December 2024
Hager

Hager U96N Útmutató

12 December 2024
Hager

Hager HIC420G Útmutató

12 December 2024
Hager

Hager HIC494G Útmutató

12 December 2024
Hager

Hager HIC493G Útmutató

12 December 2024
Hager

Hager HIC495G Útmutató

12 December 2024
Hager

Hager HFD306 Útmutató

12 December 2024
Hager

Hager FZ771A Útmutató

12 December 2024