Használati útmutató Liberty Pumps CSP-257

Liberty Pumps Pompa CSP-257

Olvassa el alább 📖 a magyar nyelvű használati útmutatót Liberty Pumps CSP-257 (14 oldal) a Pompa kategóriában. Ezt az útmutatót 5 ember találta hasznosnak és 2 felhasználó értékelte átlagosan 4.5 csillagra

Letöltés PDF

Oldal 1/14

IMPORTANT:

Prior to installation, record Model, Serial Number, and

Code Number from pump nameplate for future reference.

MODEL ________________________

SERIAL ______________________

CODE ______________________

INSTALLATION

DATE _____________________ __

CSP-237 1/3HP 115V 60Hz

CSP- 7 1/3HP 115V 60Hz 25

CSP-457 1/2HP 115V 60Hz

7000 Apple Tree Avenue

Bergen, NY 14416

Phone: (800) 543-2550

Fax: (585) 494-1839

www.libertypumps.com

Contents

1.) General Information and Safety

Guidelines

2.) Installation

3.) Maintenance and Troubleshooting

Installation Manual 4353 0C00

Model CSP-237, CSP-257, and CSP-457 Crawl Space Pump

Before installation, read the following instructions carefully. Each Liberty pump is individually factory tested to insure proper

performance. Closely following these instructions will eliminate potential operating problems, assuring years of trouble-free service.

 Risk of electric shock. Always disconnect the pump from the power source before handling or making adjustments.

 The electrical connections and wiring for a pump installation should only be made by qualified personnel.

 This pump is supplied with a grounding conductor and grounding-type attachment plug. To reduce the risk of electric shock, be

certain that it is connected only to a properly grounded, grounding-type receptacle.

 Do not bypass grounding wires or remove ground prong from attachment plugs.

 Do not use an extension cord.

 This pump requires separate, properly fused and grounded branch circuit. Make sure the power source is properly sized for the a

voltage and amperage requirements of the pump, as noted on the nameplate.

 The electrical outlet shall be within the length limitations of the pump power cord, and at least 4 feet above floor level to minimize

possible hazards from flood conditions.

 The installation must be in accordance with the National Electric Code and Plumbing Codes as well as all applicable local codes

and ordinances.

Fig. 1 – Typical Residential Installation

This is a recommended installation only.

1. General Information and Safety Guidelines

2. Installation

Figure 1

Application: The CSP- , CSP-257, and CSP-457 crawl space pumps are designed for use a crawl space or where pooling water 237 in

is occurring. Allowing the water in the pump or discharge line to freeze may cause damage to the pump. In colder regions, the pump

should only be installed indoors or deep enough to be below the frost line.

A. For in ground installation a hole should excavated as small as possible, leaving at least 8” of diametrical clearance. BACKFILL:

Course gravel is recommended for backfill.

B. The CSP- , CSP-257, and CSP-457 include a perforated basin for gathering water. Additional inlets may be added with INLET: 237

a hole saw for allowing drain lines or weep tiles.

C. When attaching the discharge, place the pump in the basin being careful to keep float from any obstruction or from DISCHARGE:

hitting the tank wall. The CSP- , CSP-257, and CSP-457 include a DHK-24 discharge hose kit. A 1-1/2” X 1-1/4” hose adapter 237

will thread into the pump discharge. The 24’ flexible hose will fit over the barbed fitting of the adapter and should be tightened

down with a hose clamp. The hose will fit through the grommet in the basin cover and can be cut to the required length. Exit the

discharge of water in an area that will drain away from the building and foundation.

D. The CSP- , CSP- and CSP-457 include a threaded check valve for use with the discharge hose. If the CHECK VALVE: 237 257,

pump is short cycling, then a check valve may be required. This would prevent water from draining back through the discharge

hose into the basin. When using a check valve, the discharge line must be protected from freezing by running the discharge deep

enough below ground level to be beneath the frost line. See figure 1.

E. The pump power cord is equipped with a grounding conductor and grounding-type 3-prong plug. It should be POWER CORD:

connected to a separately fused, grounded, 3-wire grounding-type receptacle of 15-amp capacity with the proper . Make sure 115V

all electrical wiring and connections are in accordance with the National Electric Code and all applicable local codes.

 Risk of electric shock. Always disconnect the pump from the power source before handling or making adjustments.

 DO NOT remove the plug or ground prong.

 DO NOT use an extension cord.

Termékspecifikációk

Márka:	Liberty Pumps
Kategória:	Pompa
Modell:	CSP-257

Szüksége van segítségre?

Ha segítségre van szüksége Liberty Pumps CSP-257, tegyen fel kérdést alább, és más felhasználók válaszolnak Önnek

Az Ön neve*

Az Ön e-mail címe*

Írja ide kérdését

Útmutatók Pompa Liberty Pumps

Liberty Pumps 250 Útmutató

1 Október 2024

Liberty Pumps 457 Útmutató

1 Október 2024

Liberty Pumps 230 Útmutató

1 Október 2024

Liberty Pumps CSP-257 Útmutató

1 Október 2024

Liberty Pumps LE51A Útmutató

18 Augusztus 2024

Útmutatók Pompa

Legújabb útmutatók Pompa

Einhell Royal TMP-R 400 Útmutató

5 December 2024

Gardena RWT Pump 2000/2 Li-18 Útmutató

16 Október 2024

Ozito PTP-012A Útmutató

15 Október 2024

15 Október 2024

15 Október 2024

15 Október 2024

15 Október 2024

Nefit VentiLine Útmutató

12 Október 2024

PowerPlus POWXG9513 Útmutató

7 Október 2024

Bestway Flowclear 58647 Útmutató

2 Október 2024