Használati útmutató Klipsch IC-SW-8T 2

Klipsch mélynyomó IC-SW-8T 2

Olvassa el alább 📖 a magyar nyelvű használati útmutatót Klipsch IC-SW-8T 2 (6 oldal) a mélynyomó kategóriában. Ezt az útmutatót 9 ember találta hasznosnak és 2 felhasználó értékelte átlagosan 4.5 csillagra

Letöltés PDF

Oldal 1/6

I C - S W - 8 T 2 I N E N G S U B W O R- C I L I O F E

O ’ M WW N E R S A N U A L A N D A R N T YR A

3. To install the tilebridge, fold the rail side of the ring back

upon itself using the spring tensioner on the reinforcement ring

to allow insertion into the cutout hole. Once it is inserted into

the cutout hole, release the reinforcement ring such that it

unfolds back to its normal position. Position tilebridge over

cutout hole.

4. The wiring compartment is intended as a termination point

for the audio circuit. Access to this compartment is gained by

removing the terminal cover located on the back of the

speaker. The terminal cover will accept the appropriate

conduit/wire adapter. Feed wires through conduit/wire

adapter and connect to the input terminal according

to the desired operation mode. Be sure to observe

proper polarity. Replace the terminal cover and tighten the

conduit/wire adapter to secure the wire.

Caut on When conne ng 70V 00Vi : cti or 1 distributed

li su mine en systems, take care to re prop ter er nal

c i . i to t low impe nce ter -onnect on Connect on he da mi

nal c r t sp k d ag amp fierould esul in ea er am e, li

da e, h.mag or bot

Than ou or pu ha ing ouk y f rc s y r

Klips IC-S -8 in-ceiling su ooch W T2 bw fer.

The IC-SW-8T2 in-ceiling speaker is designed for music reinforce-

ment applications. Unobtrusive, these loudspeakers are engi-

neered for easy, versatile installation.

The IC-SW-8T2 features a transformer-less design for 70.7V/100V

distributed-line systems. Some of the benefits of this design are:

Elimintation of transformer saturation at high output levels,

elimination of transformer insertion losses, improved bandwidth

(particularly at low frequencies), and improves power transfer to

the loudspeaker at low frequencies. For applications where 4

ohm mono or 8 ohm stereo operation is required, the mode of

operation can be selected by using an optional connection

located on the back input terminal and by properly setting the

rotary switch located under the grill.

Before installing your speakers take a moment to check the

contents of the cartons and make sure nothing has been

damaged in transit.

Content s Descriptio n QUA TYNTI

Speaker Module 1

Grille 1

Reinforcement Ring 1

Rails 2

Cardboard Cutout Template and Paint Mask 1

Screws (Attach Rails to Reinforcement Ring) 2

3/8" Adapter Fittings 1

1/2" Adapter Fittings 1

Installation Guideline s

The IC-SW-8T2 includes a tilebridge for use when installing

the loudspeaker into suspended ceilings or wherever additional

reinforcement of the ceiling material is required. The tilebridge

and loudspeaker are designed such that installation may be

accomplished where access above the ceiling is not possible

or may be difficult.

Installation

1. The tilebridge is composed of three parts—a reinforcement ring

and two rails. The two rails should be attached to the

reinforcement ring using the two included screws as shown below.

Caution: Be co wi and all building code sure to mply th any s

in our ea y ar .

2. To install your IC-SW-8T2 cut out a hole in the ceiling using

either the cardboard cutout template provided with your speak-

ers or consult the measurements below. Pull wiring through hole.

I C - S W - 8 T 2

I C - 8 T 2 o u n- SW " R12.5 d

5. Insert the speaker into the cutout hole. With a #2 Phillips screw-

driver, tighten the four dog clamps until they are seated securely

against the ceiling surface. Do not overtighten.

6. For installations using 70v/100v input connection, set the

switch on the front panel to "70V/100V".

For low impedance, stereo applications, the switch should be

set to 8 ohms stereo.

For low impedance, mono applications, the switch should be

set to 4 ohm mono.

In all cases, please make sure the speaker wires are connect-

ed to the appropriate terminal on the back.

7. Using the flat of your hand, insert grille into speaker frame

making sure it is securely seated and flush.

S s Ta bei m ic

A seismic tab, located on the back of the speaker, is used

as a secondary security point. Some construction codes may

require its use. To utilize the seismic tab, run a support wire

from a secure point in the ceiling and attach it to the tab.

Be sure to consult the construction codes in your area.

Klipsch recommends the use of this tab in all installations as

a secondary means of support.

70V

60W

120W

30W

100V

IC-SW-8T2 tap selectable

Termékspecifikációk

Márka:	Klipsch
Kategória:	mélynyomó
Modell:	IC-SW-8T 2

Szüksége van segítségre?

Ha segítségre van szüksége Klipsch IC-SW-8T 2, tegyen fel kérdést alább, és más felhasználók válaszolnak Önnek

Az Ön neve*

Az Ön e-mail címe*

Írja ide kérdését

Útmutatók mélynyomó Klipsch

Klipsch KI-115-SMA-II Útmutató

1 Január 2025

Klipsch KI-215-SMA-II Útmutató

1 Január 2025

Klipsch RSW-10 Útmutató

31 December 2025

Klipsch Reference RW-5802 II Útmutató

9 December 2024

Klipsch SW-310 Útmutató

18 Szeptember 2024

Klipsch RSW SUB Útmutató

16 Szeptember 2024

Klipsch Icon Series XW Sub Útmutató

8 Szeptember 2024

Klipsch C Series C-310ASWi Útmutató

8 Szeptember 2024

Klipsch SUB 260 Útmutató

2 Szeptember 2024

Klipsch SW-10 Útmutató

31 Augusztus 2024

Útmutatók mélynyomó

Legújabb útmutatók mélynyomó

Phase Technology IW200-II Útmutató

4 Április 2025

Wet Sounds ZERO 10 S4 XZ-W Útmutató

2 Április 2025

SoundTube CM1001D Útmutató

2 Április 2025

JL Audio FS108-W5 Útmutató

31 Március 2025

Phase Technology PL-12p Útmutató

30 Március 2025

ETON Graphit 8-2 Útmutató

19 Március 2025

ETON Graphit 8-4 Útmutató

19 Március 2025

ETON Graphit 10-4 Útmutató

19 Március 2025

ETON MW 10 FLAT Útmutató

19 Március 2025

ETON PW 8 Útmutató

19 Március 2025