Használati útmutató Kern ORA 3HB

Kern Mérőberendezések ORA 3HB

Olvassa el alább 📖 a magyar nyelvű használati útmutatót Kern ORA 3HB (2 oldal) a Mérőberendezések kategóriában. Ezt az útmutatót 4 ember találta hasznosnak és 2 felhasználó értékelte átlagosan 4.5 csillagra

Letöltés PDF
Oldal 1/2
1
2
CONTENT S
1 Technical data.................................................................................................1
2 Description......................................................................................................2
3 General information 3 .......................................................................................
3.1 Bestimmungsgemäße Verwendung 3 .............................................................
3.2 Warranty..........................................................................................................3
4 Basic safety information 4 ...............................................................................
4.1 Follow the instructions in the operating manual 4 .......................................
4.2 Warning .......................................................................................................4-5
5 Supplied items 5 ................................................................................................
6 Before the first use 6 ........................................................................................
7 Use/measurement.........................................................................................6
7.1 Zero point calibration 7-8 ................................................................................
7.2 Additional advice 9 ............................................................................................
7.3 Measuring procedure 9-10 ..............................................................................
8 Cleaning and maintenance 11 .........................................................................
9 Storage .........................................................................................................11
10 Service.......................................................................................................... 12
11 Disposal ........................................................................................................ 12
12 Additional information 12 ................................................................................
13 Brix to refractive index (nD) conversion table 13 .........................................
14 Annex ............................................................................................................ 14
1. Technical data
Models
KERN
Measuring
range and
Scales
Scale
graduations
Accuracy
Dimensions
Product
Net weight
ORA 3 HBHA/
58-92% Brix
38-43°Bé
12-27% water
0,5% Brix
0,5°Bé
1 % water
160x40x40mm 0,140kg
ORA 6 HBHA/
12-30%
water content
in honey
0,1%
water content
in honey
168x40x40mm 0,140kg
Operating manual
Analogue refractometer
KERN & Sohn GmbH
KERN ORA 3 HB Baumé, Brix,HA/
honey moisture
ORA 6 HB Honey refractometerHA/
Ziegelei 1
D-72336 Balingen
E-Mail: info@kern-sohn.com
Tel: +49-[0]7433-9933-0
Fax: +49-[0]7433-9933-149
Internet: www.kern-sohn.com
GB
2. Description
1. Prism cover
2. Prism surface
3. Adjustment screw
4. Eyepiece with rubber eyeshade
5. Diopter adjustment ring
6. Optical tubes with rubber grip
Example scale on
ORA 3 HB
1
6
3
5
4
2
Version 1.1 05 / 2016
7. Storage box
8. Pipette
9. Refractometer
10. Contact liquid
(Clove oil)
11. Adjustment tool
12. Cleaning cloth
5
3
4
3. General information
3.1 Intended use
The refractometer is a measuring instrument for determining the refractive index of
transparent substances in the liquid or the solid state. It is used to observe the
behaviour of light as it passes from a prism with known properties to the substance
being tested.
Use of the refractometer for other purposes is contrary to its intended use and may
be hazardous. The manufacturer shall not be liable for any damages caused
by improper use.
3.2 Warranty
The warranty shall be void in the event of:
▸ Failure to observe the instructions in the operating manual
▸ Use for purposes other than those described
▸ Modifications or opening the device housing
▸ Mechanical damage and/or damage resulting from media, liquids,
natural wear and tear
4. Basic safety information
4.1 Follow the instructions in the operating manual
▸ Carefully read through the operating manual even if you have prior
experience with KERN refractometers.
▸ Every language version includes a non-authoritative translation.
The original German document is the definitive version.
4.2 Warning
▸ Do not let acids come into contact with skin or eyes. If acid comes into contact
with skin, flush with copious amounts of water. Shower if larger areas of skin are
affected.
▸ If acid comes into contact with eyes, keep the eyelid open and flush the eye with
running lukewarm water from the outer corner to the inner corner. Flush eyes for
at least 15 minutes. Then consult a doctor or ophthalmologist immediately.
▸ Thoroughly clean the refractometer aer each use.
▸ The refractometer must not be exposed to extreme temperatures, high
mechanical stresses, strong direct sunlight or high humidity.
▸ This refractometer is not a toy. Keep out of reach of children.
▸ Make sure that you will not be hit by anything else while you are using the
refractometer, as this could cause serious eye injuries
▸ The rubber eyeshade may cause irritation when in prolonged contact with the
skin. If this happens, consult your doctor.
▸ Do not touch the lenses with your fingers.
6. Before the first use
Remove the protective film (if present) from the prism surface [2] and check that
the rubber eye-cup
[4] is fitted correctly.
7. Use/measurement
The refractometer can be used to quickly and accurately determine the refractive
index of transparent substances, liquid or solid ones. To ensure correct measure-
ment, the measuring device should be adjusted before measurements are carried
out. Please make sure your hands are dry before handling the measuring device.
5. Supplied items
Aer unpacking and before using the device for the first time, check that all
listed parts have been supplied. Replace damaged or faulty parts immediately
and do not put them into operation.
▸ Refractometer
▸ Storage box
▸ Pipette
▸ Adjustment tool
▸ Cleaning cloth
▸ Calibration block + Contact liquid ( )Clove oil
!
6
Avoid bringing the supplied contact liquid (clove oil) into contact with the prism
cover [1]. Even the smallest amounts of clove oil will damage the material of the
cover and lead to its opacification.
Therefore, pay big attention to this aspect while carrying out the adjustment of the refractometer
described below.
If still there is accidentally contact between clove oil and the prism cover, it would not affect
subsequent measurement operations even when high opacification occurs.
Important!
7
14
8
9
10
12
11
13
7.1 Zero point calibration
▸ Hold up the refractometer against a sufficiently bright light source and look through
the eyepiece [5], holding the rubber eyeshade [4] closely against your eye/glasses.
▸ Rotate the eyepiece [5] to adjust it for your eyesight, until you can see the scale
sharply.
▸ Open the prism cover [1
].
▸ Thoroughly clean the prism [2] and the underside of the prism cover [1] using a so
cloth or soft paper (with alcohol if necessary) and wipe dry.
▸ Moisten the polished surface of the calibration block with the contact fluid. Now put the
block with the moistened surface downward onto the prism surface [2].
▸ Close the prism cover [1]. The amount of fluid should be sufficient to moisten most of the
block surface. There should not be any air bubbles between the measuring prism [2] and
calibration block.
▸ Wait about 30 seconds to allow the temperatures of the fluid and prism to equalise.
▸ Look through the eyepiece
[4]
while pointing the refractometer‘s prism surface [2]
at a bright light source.
▸ Through the eyepiece [
4], you will see a bright and a blue field. The boundary line
between them shows the value on the scale which is also visible measured
through the eyepiece [
4]
.
▸ Use the supplied adjustment tool
[11] to turn the adjustment screw [
3]
behind
the prism surface [2
]
(under the rubber cap), and adjust the scale so that the
measuring device is optimally set up by moving the boundary line upwards or downwards.
Calibration value ORA A/ B: 3H 3H 78.8 % (Brix) (See the calibration line in the scale)
Calibration value ORA A/ B: % ( )3H 3H 19,6 Water content (See the calibration line in the scale)
▸ Repeat step 4 (cleaning)
.
Important!
The ambient/room temperature and the sample temperature influ-ence
the refractometer measuring result. The scales of the refractometer
models, which have " B" in its name, are designed for an ambient H
7.2 Additional advice
It is important that the samples being measured are representative samples. For
samples that evaporate easily, measurements should be carried out quickly. The
samples should be at the same temperature as the measuring instrument in order
to achieve an accurate result.
7.3 Measuring procedure
▸ Make sure your hands are dry before handling the refractometer.
▸ Open the prism cover [1]
and use the supplied pipette [8] to apply a few drops of
the sample liquid [8
] onto the prism surface [2]. Close the prism cover
[1]. Spread
the liquid evenly by pressing down on the prism cover [1] and elimi-nate any air
bubbles present.⇨
▸ Hold the device horizontally and wait about 30 seconds
(
for optimal tempera-ture
equalisation between the sample and device).
▸ View the measurement scale through the eyepiece [4]. Point the prism surface [2]
of the refractometer at a bright light source while doing this.
▸ Rotate the adjustment ring [5]
on the eyepiece [
4]
to adjust the focus.
▸ The boundary line will move on the measurement scale depending on the concen-
tration. This bright/dark boundary line shows the result on the scale.
▸ If the temperature deviates from +20 °C , and a refractometer without ATC is used
correct the measured result using the corresponding value from the temperature
correction table [13
].
▸ Carefully clean the supplied pipette
[8] and the refractometer aer carrying out
the measurement.
Important!
Aer every measurement, use a lint-free, absorbent cloth to remove
the fluids from the prism surface [2] and prism cover [1]. Then
carefully clean the prism and prism cover using a cloth moistened
with water or if necessary alcohol, and dry both parts using a so,
dry and lint-free cloth. Avoid rubbing the prism [
2]
.
9
BRIX
Refractive
index BRIX
Refractive
index BRIX
Refractive
index
%
nD
%
nD
%
nD
0 1.33299 30 1.38115 60 1.44193
1
1.33442
31
1.38296
61
1.44420
2 1.33586 32 1.38478 62 1.44650
3 1.33732 33 1.38661 63 1.44881
4 1.33879 34 1.38846 64 1.45113
5 1.34026 35 1.39032 65 1.45348
6 1.34175 36 1.39220 66 1.45584
7 1.34325 37 1.39409 67 1.45822
8 1.34476 38 1.39600 68 1.46061
9 1.34629 39 1.39792 69 1.46303
10 1.34782 40 1.39986 70 1.46546
11 1.34937 41 1.40181 71 1.46792
12 1.35093 42 1.40378 72 1.47037
13 43 1.40576 73 1.35250    1.47285
14 1.35408 44 1.40776 74 1.47535
15 1.35568 45 1.40978 75 1.47787
16 46 1.41181 76 .48040 1.35729 1 
17 1.35891 47 1.41385 77    1.48295
18 1.36054 48 1.41592 78 1.48552
19 49 1.41799 79 1.4881 1.36218
20 1.36384 50 1.42009 80 1.49071
21 1.36551 51 1.42220 81 1.49333
22 1.36720 52 1.42432 82 1.49597
23
1.36889
53
1.42647
83
1.49862
24 1.37060 54 1.42862 84 1.50129
25 1.37233 55 1.43080 85 1.50398
26 1.37406 56 1.43299
27 1.37582 57 1.43520
28 1.37758 58 1.43743
29 1.37936 59 1.43967
!
8. Cleaning and maintenance
Clean the refractometer using a so, lint-free cloth moistened with either water
or, if necessary, alcohol. Do not use any aggressive or abrasive cleaning agents.
Never immerse the device in water or hold it under running water. Never handle the
device with wet or damp hands.
Never touch the measuring prism [2] with hard tools made from plastic, wood,
rubber, metal, glass etc. Hard objects can quickly damage the relatively so prism
glass, resulting in measurement errors.
The refractometer is maintenance-free.
Cleaning should be carried out immediately before and aer each use of the refrac-
tometer to maximise its life and optimise measurement results.
9. Storage
Store the refractometer in a dry, non-corrosive environment, preferably
between 10 °C and 30 °C.
10. Service
Aer reading this operating manual, if you have any questions about setting up
or using the refractometer, or if any unexpected problem occurs, please contact
your dealer. The device housing may only be opened by trained service technicians
authorised by KERN.
11. Disposal
The packaging consists of environmentally friendly materials which can be disposed
of via local recycling facilities.
The device and storage box should be disposed of by the operator in accordance
with applicable national or regional regulations at the place of use.
12. Additional information
The product may differ slightly from the illustrations. Avoid exposing the refracto-
meter to direct sunlight. Never bring the refractometer into contact with solvents.
13. Brix to refractive index (nD) conversion table
Data from „ICUMSA“ International Commission for Uniform Methods
of Sugar Analysis, at 20 °C and 589 nm wavelength.
!
% Brix
reading
0.0 5.0 10.0 15.0 20.0 25.0 30.0 35.0 40.0 45.0 50.0 55.0 60.0 65.0 70.0 75.0 80.0 85.0
Temperature °C
10.0 - - - - - - - - - - - - - - - - - - 0.53 0.56 0.59 0.62 0.65 0.67 0.69 0.71 0.72 0.73 0.74 0.75 0.75 0.75 0.75 0.75 0.74 0.73
11.0 - - - - - - -0 - - - - - - - - - - - 0.49 0.52 0.54 0.57 0.59 0.61 .63 0.64 0.65 0.66 0.67 0.68 0.68 0.68 0.68 0.67 0.67 0.66
12.0 - - - - - - - - - - - - - - - - - - 0.44 0.47 0.49 0.51 0.53 0.55 0.56 0.57 0.58 0.59 0.60 0.60 0.61 0.61 0.60 0.60 0.60 0.59
13.0 - - - - - - - - - - - 3 - - - - - - - 0.40 0.41 0.43 0.45 0.47 0.48 0.50 0.51 0.52 0.52 0.5 0.53 0.53 0.53 0.53 0.53 0.52 0.52
14.0 - - - - - - - - - - - - - - - - - - 0.34 0.36 0.38 0.39 0.40 0.42 0.43 0.44 0.44 0.45 0.45 0.46 0.46 0.46 0.46 0.45 0.45 0.44
15.0 - - - - - - - - - - - - - - - - - - 0.29 0.31 0.32 0.33 0.34 0.35 0.36 0.37 0.37 0.38 0.38 0.38 0.38 0.38 0.38 0.38 0.37 0.37
16.0 - - - - - - - - - - - - - - - - - - 0.24 0.25 0.26 0.27 0.28 0.28 0.29 0.30 0.30 0.30 0.31 0.31 0.31 0.31 0.31 0.30 0.30 0.30
17.0 - - - - - - - - - - - - - - - - - - 0.18 0.19 0.20 0.20 0.21 0.21 0.22 0.22 0.23 0.23 0.23 0.23 0.23 0.23 0.23 0.23 0.23 0.22
18.0 - - - - - - - - - - - - - - - - - - 0.12 0.13 0.13 0.14 0.14 0.14 0.15 0.15 0.15 0.15 0.15 0.15 0.15 0.15 0.15 0.15 0.15 0.15
19.0 - - - - - - - - - - - - - - - - - - 0.06 0.06 0.07 0.07 0.07 0.07 0.07 0.08 0.08 0.08 0.08 0.08 0.08 0.08 0.08 0.08 0.08 0.07
20.0 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00
21.0 0.06 0.07 0.07 0.07 0.07 0.07 0.08 0.08 0.08 0.08 0.08 0.08 0.08 0.08 0.08 0.08 0.08 0.07
22.0 0.13 0.14 0.14 0.14 0.15 0.15 0.15 0.15 0.16 0.16 0.16 0.16 0.16 0.16 0.15 0.15 0.15 0.15
23.0 0.20 0.21 0.21 0.22 0.22 0.23 0.23 0.23 0.23 0.24 0.24 0.24 0.24 0.23 0.23 0.23 0.23 0.22
24.0 0.27 0.28 0.29 0.29 0.30 0.30 0.31 0.31 0.31 0.32 0.32 0.32 0.32 0.31 0.31 0.31 0.30 0.30
25.0 0.34 0.35 0.36 0.37 0.38 0.38 0.39 0.39 0.40 0.40 0.40 0.40 0.40 0.39 0.39 0.39 0.38 0.37
26.0 0.42 0.43 0.44 0.45 0.46 0.46 0.47 0.47 0.48 0.48 0.48 0.48 0.48 0.47 0.47 0.46 0.46 0.46
27.0 0.50 0.51 0.52 0.53 0.54 0.55 0.55 0.56 0.56 0.56 0.56 0.56 0.56 0.55 0.55 0.54 0.53 0.52
28.0 0.58 0.59 0.60 0.61 0.62 0.63 0.64 0.64 0.64 0.65 0.65 0.64 0.64 0.64 0.63 0.62 0.61 0.60
29.0 0.66 0.67 0.68 0.69 0.70 0.71 0.72 0.73 0.73 0.73 0.73 0.73 0.72 0.72 0.71 0.70 0.69 0.68
30.0 0.74 0.75 0.77 0.78 0.79 0.80 0.81 0.81 0.81 0.82 0.81 0.81 0.81 0.80 0.79 0.78 0.75 0 .77
14. Annex
Table 1: International Temperature Correction Table for °Brix (
% sugar gradient)
Correct the result by the following values
(refractometer must be correctly
adjusted at 20 °C
).
temperature of +20 °C! If the measurements are carried out at a temperature other than +20 °C,
the results must be correspondingly corrected. A correction table can be found in the annex,
Point 14. Refractometer models, which have " A" in its name, are equipped with an automatic H
temperature compensation (ATC). Between +10°C and +30°C measurement differences due to
temperature changes are automatically compensated.

Termékspecifikációk

Márka: Kern
Kategória: Mérőberendezések
Modell: ORA 3HB

Szüksége van segítségre?

Ha segítségre van szüksége Kern ORA 3HB, tegyen fel kérdést alább, és más felhasználók válaszolnak Önnek


Útmutatók Mérőberendezések Kern

Kern

Kern KFP 1500V40SM Útmutató

1 Április 2025
Kern

Kern ORA 6HB Útmutató

1 Április 2025
Kern

Kern ORA 3AB Útmutató

1 Április 2025
Kern

Kern ORA 10BA Útmutató

1 Április 2025
Kern

Kern ORA 3HB Útmutató

1 Április 2025
Kern

Kern ORA 1UB Útmutató

1 Április 2025
Kern

Kern KIP 3000V20LM Útmutató

1 Április 2025
Kern

Kern ORA 2PB Útmutató

1 Április 2025
Kern

Kern KFU 1500V20M Útmutató

1 Április 2025
Kern

Kern ORA 90BE Útmutató

1 Április 2025

Útmutatók Mérőberendezések

Legújabb útmutatók Mérőberendezések

Uni-T

Uni-T UT220 Útmutató

3 Április 2025
Uni-T

Uni-T UT681C Útmutató

3 Április 2025
Uni-T

Uni-T UT216C Útmutató

3 Április 2025
Uni-T

Uni-T UT611 Útmutató

3 Április 2025
Uni-T

Uni-T UT210D Útmutató

3 Április 2025
Uni-T

Uni-T UT210C Útmutató

3 Április 2025
Uni-T

Uni-T UT210B Útmutató

3 Április 2025
Uni-T

Uni-T UT682 Útmutató

3 Április 2025
Uni-T

Uni-T UT275 Útmutató

3 Április 2025
Uni-T

Uni-T UT08A Útmutató

3 Április 2025