Használati útmutató Jabsco 23680-4003

Jabsco Pompa 23680-4003

Olvassa el alább 📖 a magyar nyelvű használati útmutatót Jabsco 23680-4003 (2 oldal) a Pompa kategóriában. Ezt az útmutatót 2 ember találta hasznosnak és 2 felhasználó értékelte átlagosan 4.5 csillagra

Letöltés PDF

Oldal 1/2

MODELS:

23680-4003 12V DC

23680-4103 24V DC

COMMERCIAL DUTY

WATER PUPPY

FEATURES:

Continuous rated, medium duty pumps for

bilge and general purpose use.

l ISO 8846 MARINE (Ignition protection).

l ISO 8849 MARINE (Bilge pump standard).

l Small bilge debris present no problem to

these bronze bodied, flexible impeller

pumps.

l Simple design means fewer wearing

parts.

l 32 lpm (6.5 UK gpm) output @ 3m (10ft)

head.

l Self priming to 1.2m (4 ft).

INSTALLATION INSTRUCTIONS:

Jabsco Water Puppy can be mounted on any flat

surface. Fit the pump in a dry, well ventilated

position where there is full access for service. If

installed in a vertical position the motor must be

above the pump head. Use the rubber grommets

provided to minimise vibration, do not overtighten the

mounting screws.

Secure 25mm (1”) id hose either direct to the

discharge ports or to ½” BSP male threaded fittings

using stainless steel hose clamps. Use spiral

reinforced hose (with a smooth internal bore) that will

not collapse under suction, or rigid or semi rigid

pipework systems. The pipework must be compatible

with the liquid being pumped. Pipe runs should be

kept as straight and short as possible, avoiding rising

and dipping over obstructions. Fit a strainer on the

inlet hose to prevent larger debris from entering the

pump.

WIRING INSTRUCTIONS

Make all electrical connections in dry locations,

connections in humid environments should be sealed

to prevent corrosion. Protect the circuit with a

correctly rated fuse or circuit breaker in the orange

positive (+) lead as close as possible to the power

source. Connect the black motor wire to the negative

(-) battery terminal. Inadequate voltage at the motor

terminals when the pump is running (not less than

10% below rated voltage at full load) due to partially

discharged batteries or insufficient cable size may

result in blowing fuses, failure to start or poor pump

performance.

WARNING: If the fuse fails

repeatedly do not fit a heavier fuse or

bridge the fuse terminals with silver

paper or metal wire. Failure to observe

this instruction may result in a fire

hazard due to overheating of cables.

WARNING: All marine pumps

discharging overboard must be

installed with the overboard discharge

well above both static and heeled

waterlines.

m ft lpm UK gpm

2 7 35 7.7

3 10 32 7

4 13 30 6.6

6 20 25 5.5

WATER PUPPY PERFORMANCE

TOTAL HEAD

WATER PUPPY

Approximate performance for new pump,

running water at 20°C with fully charged battery

WARNING: Do not use any Jabsco

pump for petrol, petroleum products or

any products with a flash point below

37°C (98°F), explosion or death may

occur.

MODEL

NO.

VOLTAGE

MAXIMUM

AMP

DRAW

MAXIMUM

FUSE

SIZE

MINIMUM

WIRE

SIZE

MAXIMUM LENGTH

BETWEEN (+) & (-)

BATTERY TERMINALS

23680-4003 12 volt 13 amp 15 amp

30 / 0.25mm

(1.5mm²)

4.5m (15ft) *

32 / 0.2mm

(1.0mm²)

ELECTRICAL WIRING INFORMATION

23680-4103

24 volt

6 amp

10 amp

4.5m (15ft) *

DIMENSIONAL DRAWING & PARTS LIST

WEIGHT: Water Puppy - 3.0kg (6.6lb)

Warranty: All products of the company are sold and all services of the company are offered subject to the company’s warranty and terms and conditions of sale, copies of which will be furnished upon request.

100 Cummings Center, Ste 535-N, Beverly, MA 01915

+1 978 281 0440 +1 978 283 2619