Használati útmutató Jabsco 23620-4103

Jabsco Pompa 23620-4103

Olvassa el alább 📖 a magyar nyelvű használati útmutatót Jabsco 23620-4103 (2 oldal) a Pompa kategóriában. Ezt az útmutatót 6 ember találta hasznosnak és 2 felhasználó értékelte átlagosan 4.5 csillagra

Letöltés PDF

Oldal 1/2

MODELS:

23620-4003 12V

23620-4103 24V

MINI PUPPY

FEATURES:

Continuous rated, medium duty pumps for

bilge and general purpose use.

zISO 8846 MARINE (Ignition protection).

zISO 8849 MARINE (Bilge pump standard).

zSmall bilge debris present no problem to

these brass bodied, flexible impeller

pumps.

zSimple design means fewer wearing

parts.

z6 lpm (1.3 UK gpm) output @ 2m (6.6ft)

head.

zSelf priming to 1.5m (5 ft).

INSTALLATION INSTRUCTIONS:

Jabsco Mini Puppy can be mounted on any flat

surface. Fit the pump in a dry, well ventilated

position where there is full access for service. If

installed in a vertical position the motor must be

above the pump head. Use the rubber grommets

provided to minimise vibration, do not overtighten the

mounting screws.

Secure 25.4mm (1”) id hose direct to the discharge

ports using stainless steel hose clamps, or use 3/8”

BSP / NPT pipe fittings using suitable jointing tape.

Use spiral reinforced hose (with a smooth internal

bore) that will not collapse under suction, or rigid or

semi rigid pipework systems. The pipework must be

compatible with the liquid being pumped. Pipe runs

should be kept as straight and short as possible,

avoiding rising and dipping over obstructions. Fit a

strainer on the inlet hose to prevent larger debris

from entering the pump.

WIRING INSTRUCTIONS

Make all electrical connections in dry locations,

connections in humid environments should be sealed

to prevent corrosion. Protect the circuit with a

correctly rated fuse or circuit breaker in the red

positive (+) lead as close as possible to the power

source. Connect the black motor wire to the negative

(-) battery terminal. Inadequate voltage at the motor

terminals when the pump is running (not less than

10% below rated voltage at full load) due to partially

discharged batteries or insufficient cable size may

result in blowing fuses, failure to start or poor pump

performance.

WARNING: If the fuse fails

repeatedly do not fit a heavier fuse or

bridge the fuse terminals with silver

paper or metal wire. Failure to observe

this instruction may result in a fire

hazard due to overheating of cables.

WARNING: All marine pumps

discharging overboard must be

installed with the overboard discharge

well above both static and heeled

waterlines.

m ft lpm UK gpm

2 6.6 6 1.5

4 13 5 1.3

6 19.7 4 1.1

8 26.2 2.8 0.9

MINI PUPPY PERFORMANCE

TOTAL HEAD MINI PUPPY

Approximate performance for new pump,

running water at 20°C with fully charged battery

WARNING: Do not use any Jabsco

pump for petrol, petroleum products or

any products with a flash point below

37°C (98°F), explosion or death may

occur.

DIMENSIONAL DRAWING & PARTS LIST

WEIGHT: Mini Puppy - 2.2kg (4.8lb)

* For longer installations, fit thicker cables

All dimensions in mm

MODEL

NO. VOLTAGE

MAXIMUM

AMP

DRAW

MAXIMUM

FUSE

SIZE

MINIMUM

WIRE

SIZE

MAXIMUM LENGTH

BETWEEN (+) & (-)

BATTERY TERMINALS

23620-4003 12 volt 5 amp 7.5 amp 30 / 0.25mm

(1.5mm²) 8m (26ft) *

23620-4103 24 volt 2.5 amp 5 amp 32 / 0.2mm

(1.0mm²) 8m (26ft) *

ELECTRICAL WIRING INFORMATION

KEY DESCRIPTION QUANTITY PART NUMBER

1 End Cover Screw * 3 SP1002-03

2 End Cover 1 29305-0100

3 Impeller* 1 1414-0003B

4 O-Ring* 1 X1990-131

5 Body 1 7824-2000

6 Seal* 1 93000-6100

7 Screw (pump to motor) 2 X3001-147F

8 Slinger 1 6342

Motor 12V 1 98012-2742C

Motor 24V 1 98012-2885C

SK374-0003

MINI PUPPY PARTS LIST

Service Kit (Contains Items Marked *)

Warranty: All products of the company are sold and all services of the company are offered subject to the company’s warranty and terms and conditions of sale, copies of which will be furnished upon request. The information provided