Használati útmutató Intermatic DT200LT

Intermatic kapcsoló DT200LT

Olvassa el alább 📖 a magyar nyelvű használati útmutatót Intermatic DT200LT (4 oldal) a kapcsoló kategóriában. Ezt az útmutatót 2 ember találta hasznosnak és 2 felhasználó értékelte átlagosan 4.5 csillagra

Letöltés PDF
Oldal 1/4
Libertyville, Illinois 60048
www.intermatic.com
Digital Landscape Timer
MODEL DT200LT
for use in Low Voltage Transformers up to 1200 W
SET
PROG
ON/OFF
SAFETY SECTION
WARNING
Risk of Fire or Electrical Shock
• Do Not use the timer to control devices that could have dangerous consequences due to inaccurate timing, such as sun lamps, saunas, heaters, crock pots, etc.
• Unplug the timer before replacing batteries.
• Do Not use to control receptacles.
• Installation should be in accordance with national and local electrical code requirements.
NOTICE
• Dispose of product per local regulations for disposal of used batteries.
WARNING
• Ingestion Warning: This product contains a button cell or coin battery.
• DEATH or serious injury can occur if ingested.
• A swallowed button cell or coin battery can cause in as little as .Internal Chemical Burns 2 hours
• KEEP OUT OF REACH CHILDREN new and used batteries of
• Seek immediate medical attention if a battery is suspected to be swallowed or inserted inside any part of the body.
• Remove and immediately recycle or dispose of used batteries according to local regulations and keep away from children. Do NOT dispose of batteries in household trash
or incinerate.
• Even used batteries may cause severe injury or death.
• Replace only with LR44 (1.5 V) Batteries.
• Call a local poison control center for treatment information.
• Non-rechargeable batteries are not to be recharged.
• Do not force discharge, recharge, disassemble, heat above (manufacturer’s specified temperature rating) or incinerate. Doing so may result in injury due to venting, leakage or explosion resulting in
chemical burns.
• Ensure the batteries are installed correctly according to polarity (+ and -).”
• Do not mix old and new batteries, different brands or types of batteries, such as alkaline, carbon-zinc, or rechargeable batteries.
• Remove and immediately recycle or dispose of batteries from equipment not used for an extended period of time according to local regulations.
• Always completely secure the battery compartment. If the battery compartment does not close securely, stop using the product, remove the batteries, and keep them away from children.
PRODUCT DESCRIPTION
The Intermatic DT200LT Digital Landscape Timer is a simple-to-use landscape timer to be used with low voltage transformers
up to 1200 W in order to control landscape lighting. This timer supports pre-programmed dawn/dusk times or one set of
custom ON/OFF times.
Specifications
Output
• 15 A Resistive, 120 VAC
• 12 A Inductive, 120 VAC
• 1000 W, 120 VAC
• 1/2 HP, 120 VAC
Input
• 120 VAC, 60 Hz, 2.5W max
Operating Temperature
• -40°F to 122°F (-40°C to 50°C), for 1200 W, 120 VAC
Batteries
• Two LR44 batteries that keep time and settings for up
to three months without power
TIMER OVERVIEW
Item Description Item Description
A Battery Holder H Selector Knob
B Low Battery Indicator I Reset Button
C Time of Day Display J Day of the Week Display
D SET Button K Mode Display
E PROG Button L ON/OFF Indicator Light
F ON/OFF Button M Battery Pull Tab
G Grounded Outlet (2)
ON
DAYSAV AUTO CLOCK
YEARDATE
MONTH
SKIP
EVENT
MO TU WE TH FR SA SU AM PM
OFF LOC DUSK DAWN
SET PROG ON/OFF
I
M
L
G
E
F
H
J
D
C
B
A
G
K
2
Digital Landscape Timer
INITIAL SETUP
Overview
Upon first use, you must enable the battery and then set the Time, Date, and Location.
Enabling the Battery
1. Remove the pull tab (M) from the battery holder, if
present. See FIG. 1.
2. When the display shows 12:00 AM, the timer is
ready for initial set up. See FIG. 2. If 12:00 AM does
not display, perform a Factory Reset or see the
Troubleshooting section.
Note: The timer may be set while unplugged. The display
turns OFF after 1 minute of inactivity to save battery.
Press any button to turn the display back ON.
Setting the Time, Date, and Location
Upon initial use, you can easily program these timer settings
in succession by completing the steps in this section.
1. Turn the selector knob (H) to select the correct hour of
the day. Press (D). Repeat to select the minute of SET
the day. See FIG. 2.
2. Turn the selector knob (H) to select the correct YEAR.
Press SET (D). See FIG. 3.
3. Turn the selector knob (H) to select the correct MONTH.
Press SET (D). See FIG. 3.
4. Turn the selector knob (H) to select the correct DATE.
Press SET (D). See FIG. 3.
5. Turn the selector knob (H) to select the correct Daylight
Savings Time setting. The options are OFF, US/CAN,
and Mex.
a. If in Hawaii or Arizona, select OFF. Press (D).SET
b. If you live in a part of Mexico that observes
US/Canada Daylight Savings Time, select US/CAN.
Press (D).SET
6. Turn the selector knob (H) to select the state you are in.
Press SET (D). See FIG. 4.
7. Turn the selector knob (H) to select the section of the
state you are in. Press (D). See FIG. 4.SET
8. Turn the selector knob (H) to select the time zone you
are in. Press (D). See FIG. 5.SET
9. Turn the selector knob (H) to adjust the DAWN offset
time (+/- 15, 30, 45 or 60 minute increments). Press
SET (D). Offset is the amount of minutes you want the
lights to come on before (-) or after (+) DAWN or DUSK.
Repeat for the DUSK offset time. See FIG. 6.
10. Press (D) to finish setting up the timer.SET
M
FIG 1. Removing the Pull Tab
CLOCK
PM
SET PROG ON/OFF
H
D
I
FIG 2. Setting the Time
YEARDATEMONTH
FR
SET PROG ON/OFF
H
D
FIG 3. Setting the Date
FIG 4. Setting the State
LOC
SET PROG ON/OFF
H
D
FIG 5. Setting the Time Zone
SET PROG ON/OFF
H
D
FIG 6. Setting the DAWN/DUSK Offset Time
DAWN
SET PROG ON/OFF
H
D
3
Digital Landscape Timer
Changing Configuration Settings for Time,
Date and Location
1. Press SET (D).
2. Follow steps 1 through 9 under , , Setting Time Date
and .Location
3. Press (E), to return to main screen.PROG
PROGRAMMING
This timer comes pre-programmed to turn ON at dusk and
OFF at dawn. If you wish to adjust this time to another ON/
OFF time, complete the programming steps in this section.
This timer only holds one set of ON/OFF times (either the
pre-programmed Dawn/Dusk times or the custom times you
program using the steps in this section).
Changing the Pre-Programmed Dusk (ON)
Time
To change the DUSK time to another ON time:
1. Press (E) twice.PROG
2. Turn the selector knob (H) until a time appears on the
screen. Press (E).PROG
3. Turn the selector knob (H) to select the correct ON hour.
Press PROG (E).
4. Turn the selector knob (H) for the correct ON minute.
Press SET (D). See FIG. 7.
Changing the Pre-Programmed Dawn
(OFF) Time
To change the dawn time to another OFF time:
1. Press (E).PROG
2. Turn the selector knob (H) until OFF is in the top left
corner of the screen. Press PROG (E).
3. Turn the selector knob (H) so that a time appears on the
screen. Press PROG (E).
4. Turn the selector knob (H) to select the correct OFF hour.
Press PROG (E).
5. Turn the selector knob (H) to select the correct OFF
minute. Press SET (D). See FIG. 8.
PERFORMING A FACTORY RESET
To clear any programming or reset the timer at any time,
perform these steps:
1. Press and continue to hold the button (F).ON/OFF
2. Using a paperclip, press and release the RESET
button(I).
3. Keep holding the button (F) until ‘CLR’ ON/OFF
appears on the screen, then release.
4. When you see 12:00 AM displayed, your timer is ready
for programming. See FIG. 9.
FIG 7. Changing the Dusk (ON) Time
ON
EVENT
MO TU WE TH FR SA SU PM
SET PROG ON/OFF
H
D
E
FIG 8. Changing the Dawn (OFF) Time
MO TU WE TH FR SA SU AM
OFF
SET PROG ON/OFF
H
DF
E
AM
SET PROG ON/OFF
F
I
FIG 9. Performing a Factory Reset

Termékspecifikációk

Márka: Intermatic
Kategória: kapcsoló
Modell: DT200LT

Szüksége van segítségre?

Ha segítségre van szüksége Intermatic DT200LT, tegyen fel kérdést alább, és más felhasználók válaszolnak Önnek


Útmutatók kapcsoló Intermatic

Intermatic

Intermatic DDFM Útmutató

12 December 2024
Intermatic

Intermatic DDT40 Útmutató

12 December 2024
Intermatic

Intermatic DT121K Útmutató

12 December 2024
Intermatic

Intermatic DTAV40 Útmutató

12 December 2024
Intermatic

Intermatic DT200LT Útmutató

12 December 2024
Intermatic

Intermatic HB114 Útmutató

12 December 2024
Intermatic

Intermatic HB113 Útmutató

12 December 2024
Intermatic

Intermatic HB51K Útmutató

12 December 2024
Intermatic

Intermatic HB112 Útmutató

12 December 2024
Intermatic

Intermatic HB880R Útmutató

12 December 2024

Útmutatók kapcsoló

Legújabb útmutatók kapcsoló

Hager

Hager LVS0060RPX Útmutató

12 December 2024
Hager

Hager HIB412M Útmutató

12 December 2024
Hager

Hager LVSR1VPVK4 Útmutató

12 December 2024
Hager

Hager U96N Útmutató

12 December 2024
Hager

Hager HIC420G Útmutató

12 December 2024
Hager

Hager HIC494G Útmutató

12 December 2024
Hager

Hager HIC493G Útmutató

12 December 2024
Hager

Hager HIC495G Útmutató

12 December 2024
Hager

Hager HFD306 Útmutató

12 December 2024
Hager

Hager FZ771A Útmutató

12 December 2024