Használati útmutató HQ EL-COCO20S

Olvassa el alább 📖 a magyar nyelvű használati útmutatót HQ EL-COCO20S (46 oldal) a Otthon automatizálás kategóriában. Ezt az útmutatót 5 ember találta hasznosnak és 2 felhasználó értékelte átlagosan 4.5 csillagra

Oldal 1/46
EL-COCO20FS
EL-COCO20S
(p. 2) (S. 6)
(s. 10) (p. 14)
(p. 18) (p. 22)
(o. 26) (s. 30)
(s. 34) (s. 38)
(p. 42)
Instruction manual Tele-Control
Please read this instruction manual carefully before use and check the product for eventual damage.
Pay attention that it is not in reach of children or unauthorized persons. At the end of its lifespan this
product has to be properly recycled.
Function
The Tele-control set contains a transmitter and 3 Receivers. This product can switch electrical
and electronic devices (lamps, TV-Sets, computers, christmas illumination, etc.) of a capacity of
up to 1000 W within a range of up to 5 m (free area). It is possible to switch on/off these devices
from any location through furniture and walls. The range inside buildings is limited according to the
building specic construction features.
Installation
Before using the Tele-control system it the following has to be done:
Remote control:
Insert the battery (see chapter batteries picture ).
Test the channel setting (see chapter settings).
Receiver:
Test the channel setting (see settings).
Assign the button to the socket (see settings).
Plug the remote controlled socket into a safety socket (picture1).
Plug in the device what should be remote controlled into the radio socket (picture1).
Switch on the device what shall be controlled (picture 1).
Picture 1
Control lamp signalises connection to the mains.
ON
Batteries
For the remote control a 1 V (A3) battery is used (included). Remove the cover of the battery
compartment at backside and insert the battery. Pay attention of the polarity symbols. The battery
should be changed when the range is considerable reduce or once a year. Used batteries should
not be disposed together with normal waste!
Picture 2
Channel setting
(A-E, CODE 1-5)
Battery case
3
Settings:
In case that several Tele-control or other remote control units are being used at the same location
(in the neighbourhood) the remote setting can be changed in order to avoid interferences.
The Tele-control unit has 5 channels (A-E) which can be set at the remote control itself. The setting
has to be done at the remote controlled socket as well, so the settings of the two devices match.
Several sockets can be switched with one button or one socket per button (1-5).
Setting of the radio channel at the remote control:
Push the switch at the battery compartment to the desired channel A-E (see picture )
Setting of the radio channel of each socket:
Setting must be done at the backside of the socket. Use a screwdriver to open and set the channel.
The channel setting at the remote control must be at the same position as by the socket (A-E). The
Dip-switch 6-10 indicates the buttons 1-5.
Channel=Dip-switch: A=1, B=2, C=3, D=4, E=5
Button=Dip-switch: 1=6, 2=7, 3=8, 4=9, 5=10
Picture 3
LED rot
Channel setting A-E
Switch setting 1-10
Channel A. Switch 1+6
Example 1 Example 2
Channel A, SWITCH 1 Channel D, SWITCH 3
Device is switched 1+6 Devide is switched 3+9
Remote
control
Receiver
Channel A, Switch 1+6
Remote
control
Receiver
Channel D, Switch 3+9

Termékspecifikációk

Márka: HQ
Kategória: Otthon automatizálás
Modell: EL-COCO20S

Szüksége van segítségre?

Ha segítségre van szüksége HQ EL-COCO20S, tegyen fel kérdést alább, és más felhasználók válaszolnak Önnek




Útmutatók Otthon automatizálás HQ

HQ

HQ EL-COCO20S Útmutató

14 Szeptember 2024

Útmutatók Otthon automatizálás

Legújabb útmutatók Otthon automatizálás