Használati útmutató Hitec Aggressor AM

Hitec rádió Aggressor AM

Olvassa el alább 📖 a magyar nyelvű használati útmutatót Hitec Aggressor AM (1 oldal) a rádió kategóriában. Ezt az útmutatót 3 ember találta hasznosnak és 2 felhasználó értékelte átlagosan 4.5 csillagra

Letöltés PDF

Oldal 1/1

432

1. System Specifications

a. Transmitter

b. Accessories

c. Options

2. Transmitter Functions and Operations

a. Power Switch

b. Battery Indicator LED's

c. Steering Dual Rate

d. Steering and Throttle trims

e. Tuning Cover

f. Servo Reversing switches

g. Battery Cover

h.Antenna

i.Grip Pad

j.Crystal

k.Charging Jack

l.Steering Wheel

m.Throttle Trigger

3. Transmitter Battery Installation

4. Recharging Batteries

5. Receiver and Servo Connections

a. Receiver

b. Servos

c. Battery

6. Troubleshooting Guide

7. Warnings

8. Racers Tips

sdjh

Table of Contents Introduction

Congratulations on your purchase of the Aggressor AM pistol grip radio system. The Aggressor AM is

loaded with many great features to maximize your R/C experience. Please read this manual

carefully to familiarize yourself with the operation of your new Aggressor. After reading this manual,

store it in a safe place for future reference.

Austria, Belgium, Denmark, Finland,

France, Germany, Greece, Iceland,

Ireland, The Netherland, Italy, Spain,

Norway, Portugal, United Kingdom,

Luxembourg, Sweden, Switzerland

- Ergonomically designed 2 channel Pistol Grip AM Radio

- Servo Reversing (All channels)

- Dual Rate Steering (Adjustable on the fly)

- 3 L.E.D. Battery status indicators

- Removable crystals for easy channel changing (If this is legal in your Country)

- Interchangeable rubber grip pads to fit all hand sizes

- Assorted colored grip pads and tuning covers for personalizing your radio

- Foam steering wheel for comfortable control

- Charging Jack for optional rechargeable batteries

- BEC receiver

- Standard HS-311 or 322 servo

- Receiver dry battery holder

System Features

1. System Specifications

2. Transmitter Functions and Operations

6. Troubleshooting Guide

7. Warnings

8. Racers Tips

A) Power Switch:

- Slide the switch up to turn on the transmitter, and down to turn it off.

- Warning: Always turn your transmitter on before switching on the receiver switch.

This will help prevent accidental runaways.

B) Battery Indicator LED's:

- Green is mid - high power

- Amber is mid power (You should replace or charge your batteries very soon.)

- Red is low power (Stop driving!)

C) Steering Dual Rate: This is not shown in the ima ge

- Adjusts the overall travel of the steering servo.

- Push the dial forward with your thumb for maximum steering.

- Pull the dial back with your thumb to reduce the travel.

- Use this to fine tune your vehicles handling to the track conditions.

- Use more steering travel for high bite tracks and less for low bite tracks.

D) Steering and T hrottle trims:

- The trims are used to fine-tune the point where the servo returns to center.

- Use the ST-TRIM so your vehicle will go perfectly straight when the steering wheel is centered.

If you move the trim to its maximum and the vehicle does not go straight, move the servo horn a

notch or two on the servo output spline or adjust the linkage to fix the problem. Ideally the servo horn

will have equal throw in each direction.

- Use the THR-TRIM to adjust the "Drag Brake"; this is the amount of braking that occurs when you

let go of the trigger. Be aware that too much brake may affect the servo end point preventing

maximum power.

- Tip#1: Do not mount the horn on the servo until you turn on the radio and

center the trims.

- Tip#2: Always trim your vehicle before you run or race.

E) Tuning Cover:

- Remove the tuning cover to access the servo reversing switches.

- This is also an interchangeable part with assorted colors and designs to choose from so you may

customize the look of your radio. See "Options" for more info.

F) Servo Reversing switches:

- These are used to change the direction of the servo travel for proper control when activated.

- If you steer right and the wheels go left, change the "ST" switch from NOR to REV or REV to

NOR if needed. The same applies to the throttle.

- (Note: You should not need to change the "THR" switch from NOR if using

an Electronic Speed Control.)

G) Battery Cover:

- Remove to change batteries.

J) Crystal:

- The crystal is located above the power switch and can be interchanged with different channels in

conjunction with the receiver to prevent any conflicts with other radios used in your area.

- AM Transmitter crystal part# 67475XX (XX= Your channel number)

- Warning: Use only genuine Hitec crystals. Other brands will not work properly!

K) Charging Jack:

- The charging jack is located under the power switch for use with the optional

Hitec CG-25 charger(110v only ) when using rechargeable batteries.

(See "Recharging Batteries" for more information about this feature.)

- Used to control the steering of your vehicle.

L) Steering Wheel:

- Used to control the steering of your vehicle.

M) Throttle Trigger:

- Used to control the throttle and braking for your vehicle.

- Pull the trigger for throttle and push it for braking or reverse (Reversing ESC's only.)

3. Transmitter Battery Installation

5. Receiver and Servo Connections

- Press down on the battery cover and slide in the direction illustrated.

- Remove the cover and install the batteries as shown.

- Be careful to pay close attention to the polarity of each cell or the transmitter will not operate.

- Replace the cover making sure it is closed securely.

4. Recharging Batteries

- You must install individual AAsize rechargeable batteries.

- Only use Nicad or NiMh type. (Alkaline batteries are not rechargeable).

- Connect the optional Hitec CG-25 overnight wall charger to the charging jack located under the

switch to charge. Depending on the capacity of the battery;

- A full charge on a typical Nicad will take 12-16 hours.

- A full charge on a typical NiMh will take 24-36 hours.

A) Receiver:

- The receiver in your Aggressor system includes a BEC (Battery Eliminator Circuit), which

eliminates the need for a separate receiver battery when used with a mechanical or electronic

speed control. Power input should be no more than 8.4V (7 cells)

- You can use a separate receiver battery if required for your particular model. Connect as shown.

- Be aware you should keep your antenna at least 2" away from any power wires to prevent interference.

- Run the antenna up the antenna tube as shown in your vehicles instructions.

- Warning: Be sure not to cut off any excess antenna wire, as it will shorten your operating range.

B) Servos:

- When installing the servos, refer to the manual of the vehicle for proper installation.

- Once your servos are correctly installed you will need to make sure they are properly centered.

To do this, remove the servo horns and turn on your transmitter, then the power to your receiver.

Remember; always turn your transmitter on first and off last. Failure to do so may result in loss of

control and can damage your servos and/or linkage.

- Now that the power is on, check that the servos are working properly.

- You will now center the trim knobs on the transmitter and replace the horns so that they are centered.

- Be aware they may not be perfectly centered; this is OK, just get them as close as possible.

Then use the trims for fine-tuning.

H) Antenna:

- Always extend your antenna before turning your transmitter on.

- Your antenna may be removed by turning counter clockwise.

- Warning: When collapsing your antenna, never push it from the top or it may bend!

I) Grip Pad:

- The removable grip pad helps keep your hand from slipping on the radio pistol grip handle so

you have better control of the vehicle.

- It is also available in assorted colors and sizes to customize the look and feel of your radio.

C) Battery:

- The AA receiver battery holder supplied with your radio should be used in a non-electric

vehicle that requires two servos.

- Connect the AA Receiver battery holder to the power switch supplied, and then plug the switch into the

"Batt" channel of the receiver for power.

- You will not need to connect this battery if you are using an electric car with an electronic

speed control or mechanical speed control with BEC.

Question: I installed the batteries in my transmitter, but the power lights do not come on:

Answer:

- Check that the batteries are properly installed by checking the polarity (+ and -).

Question: My radio has power, but I have no control:

Answers:

- Check to be sure the power switch is on and connected to the receiver.

- Make sure the batteries are charged (Replace or recharge if needed.)

- Make sure you are using the proper crystals.

Question: My vehicle is glitching, or the servos and/or speed control is acting erratically:

Answers:

- Check that there are no radios operating on your channel.

- Make sure your electric motor has capacitors and the comutator is clean and brushes are

not worn out. Replace if needed.

- Check for loose screws as metal-to-metal contact can cause interference.

- Make sure your receiver antenna has not been damaged or cut.

- Make sure the power wires are at least 2" away from the receiver.

- Replace the crystals if needed.

- If all fails, send the system in to be serviced, as there may be internal damage.

- Never operate your car or truck in a crowded street with traffic.

- Always extend your transmitter antenna when in operation.

- Always check the battery power indicator before use.

- Do not operate two or more models on the same frequency at the same time.

- Do not operate your model in the rain or run through standing water.

- Do not operate your model within one mile of a radio control racetrack.

- Do not operate your model while under the influence of drugs or alcohol.

- Always turn on your transmitter first and then the receiver to prevent loss of control.

- When collapsing your antenna, never push it from the top or it may bend.

- Slower is faster, Do not overdrive your car. A cleaner line around the track is faster than

more top speed. Don't overshoot the corners.

- Reduce your steering dual rate if your car is over-steering or "Loose", and increase the rate if

your car is under-steering or "Pushing."

- Add more drag brake (see Steering and Throttle trims) if your vehicle is "Pushing" into the corners.

Move the trim the other direction so your car creeps forward slightly when the throttle is at neutral if

your car is "Loose" when entering the corners.

- Don't crash! It's better to take a more conservative line than flip over and have to have a turn marshal

turn you back over.

- The most important thing to remember is to have fun!

Grip Pad

Alkaline or Nicad "AA"size

Battery Cover

Remove

Touch your dreams Touch your dreams

Touch your dreams

MADE IN KOREA

AGGRESSO RAGGRESSO RAGGRESSOR

AGGRESS ORAGGRESS ORAGGRESS ORAGGRESSOR

Product Service Information ( for USA & Canada only )

In the event you would require service to your radios, please send the parts to ::

Hitec RCD USA, Inc. Service Department

12115 Paine St.

Poway, CA 92064

Please include your name address and telephone number along

with a brief description of the failure or the work that you are requesting to be done.

A. Power Switch

B. Battery Indicator LED's

C. Steering Dual Rate

D. Steering and Throttle trims

E. Tuning Cover

F. Servo Reversing switches

G. Battery Cover

H. Antenna

I. Grip Pad

J. Crystal

K. Charging Jack

L. Steering Wheel

M. Throttle Trigger

NOR- REV NOR- REV

2CHANNEL AM RADIOCONTROL SYSTEM

ST THR

TOP

FRONT

AGGRESSOR

INSTRUCTION MANUAL

2 C HA N N E L A M R A D I O C O N T R O L S Y S T E M

AGGRESSOR

INSTRUCTION MANUAL

2 C HA N N E L A M R A D I O C O N T R O L S Y S T E M

AGGRESSOR

INSTRUCTION MANUAL

2 C HA N N E L A M R A D I O C O N T R O L S Y S T E M 2 C HA N N E L A M R A D I O C O N T R O L S Y S T E M

Battery Cover

AGGRESSOR

INSTRUCTION MANUAL

INSTRUCTION

INSTRUCTIONINSTRUCTION MANUAL

MANUAL

MANUALMANUALINSTRUCTION MANUAL

TTo

oou

uuc

cch

hh y

y yo

oou

uur

rr d

d dr

rrea

eaeam

mms

ssTouch your dreams

A) Transmitter:

- Power Output: 500mW

- Current drain 180mA

- Modulation: AM/PPM

- Power supply: 8AA alkaline, Nicad or NiMh batteries

- Frequencies: 27mhz (6 channels), 75mhz (30 channels)

B) Receiver:

- HAS-02MB

- Modulations: AM

- Power Supply: 4.8V~8.4V

- Weight: 0.81oz

- Size: 1.2"x1.9"x 0.7"

- Current drain: 30mA +/- 0.3mA

- BEC Maximum output: 3.0A

C) Servo:

- HS-322

- Voltage range: 4.8 - 6V

- Speed: 0.16sec/60 degree (6V)

- Torque: 53in/oz (6V)

- Weight: 1.6oz

- Size: 1.6" x 0.8" x 1.4"

D) Options:

- Red, Blue and Black colored grip pads in two sizes each (Sold separately).

- Tuning covers available in Red, Blue and Black, as well as custom designs in Silver Carbon,

Wood (Burl) and Camouflage (Sold separately).

X-TAL

EODFN#+0,#######

QLFDG#EDWWHU\#

7.2V - 8.4V

UHG#+.,#######

VWHHULQJ#V HUYR

WKURWWOH#VHUYR

\HOORZ#+.,##### ###

Eoxh#+0,#######

PRWRU##########

ZLWK#314xi#

FDSDFLWRU####

GXDO#OHG#####

UHG#=#EUDNH######

JUHHQ#=#IXOO#SRZHU

LQGLFDWRU####

VHW#XS#EXWWRQ

Rq2Rii#Vzlwfk

ESC Installation

ESC

RECEIVER

Nomal Installation

Termékspecifikációk

Márka:	Hitec
Kategória:	rádió
Modell:	Aggressor AM

Szüksége van segítségre?

Ha segítségre van szüksége Hitec Aggressor AM, tegyen fel kérdést alább, és más felhasználók válaszolnak Önnek

Az Ön neve*

Az Ön e-mail címe*

Írja ide kérdését

Útmutatók rádió Hitec

Hitec Aggressor FM Útmutató

17 Július 2024

Hitec Aggressor AM Útmutató

17 Július 2024

Hitec Aggressor SRX Útmutató

17 Július 2024

Hitec Aggressor CRX Útmutató

17 Július 2024

Útmutatók rádió

Legújabb útmutatók rádió

Albrecht DR-330 Útmutató

16 Január 2025

Thomson WKR60BT Útmutató

14 Január 2025

MB Quart GMR7V1.2 Útmutató

14 Január 2025

Uniden X70 Útmutató

13 Január 2025

Roadstar HIF-1899TUMPK Útmutató

13 Január 2025

Clas Ohlson SW-615 Útmutató

13 Január 2025

Tivoli Audio Albergo Útmutató

12 Január 2025

Furrion DV1230-BL Útmutató

12 Január 2025

Ferguson Regent P1 DAB+ Útmutató

12 Január 2025

Hyundai TRC 533 AU3BS Útmutató

12 Január 2025