Használati útmutató Fluke Networks OptiFiber Pro

Fluke Networks OptiFiber Pro

Olvassa el alább 📖 a magyar nyelvű használati útmutatót Fluke Networks OptiFiber Pro (10 oldal) a kategóriában. Ezt az útmutatót 4 ember találta hasznosnak és 2 felhasználó értékelte átlagosan 4.5 csillagra

Oldal 1/10
PN 4095544 January 2012, Rev. 5 8/2015
2013-2015 Fluke Corporation
All product names are trademarks of their respective companies.
*4095544*
OptiFiber® Pro
OTDR
Getting Started Guide
The OptiFiber® Pro Optical Time Domain Reflectometer (OTDR)
module attaches to a Versiv main unit to make a rugged, hand-
held tester that lets you locate, identify, and measure reflective
and loss events in multimode and singlemode fibers. Typical
maximum test ranges are 35 km maximum at 1300 nm for
multimode fiber and 130 km maximum at 1550 nm for
singlemode fiber.
Accessing the Product Manuals
This guide provides basic information to help you get started
using the tester. For more detailed information, see the latest
versions of the Versiv Users Manual and the Versiv Technical
Reference Handbook provided on the Fluke Networks website.
Safety Information
Warning
To prevent possible fire, electric shock, or personal injury:
Read all safety information before you use the
Product.
Carefully read all instructions.
Warning or Caution: Risk of damage or destruction to equip-
ment or software. See explanations in the manuals.
Warning: Risk of fire, electric shock, or personal injury.
Warning: Class 1 or Class 2 lasers. Risk of eye damage from haz-
ardous radiation.
This key turns the Product on and off.
Do not open the case. You cannot repair or replace
parts in the case.
Do not modify the Product.
Use only replacement parts that are approved by
Fluke Networks.
Do not touch voltages > 30 V AC rms, 42 V AC peak,
or 60 V DC.
Do not use the Product around explosive gas, vapor,
or in damp or wet environments.
Use this Product indoors only.
Use the Product only as specified, or the protection
supplied by the Product can be compromised.
Do not use and disable the Product if it is damaged.
Do not use the Product if it operates incorrectly.
Batteries contain hazardous chemicals that can
cause burns or explode. If exposure to chemicals
occurs, clean with water and get medical aid.
Remove the batteries if the Product is not used for
an extended period of time, or if stored in
temperatures above 50 °C. If the batteries are not
removed, battery leakage can damage the Product.
The battery door must be closed and locked before
you operate the Product.
Repair the Product before use if the battery leaks.
Recharge the batteries when the low battery
indicator shows to prevent incorrect measurements.
Do not disassemble or crush battery cells and
battery packs.
Do not put battery cells and battery packs near heat
or fire. Do not put in sunlight.
Have an approved technician repair the Product.
For Products with rechargeable batteries, use only
AC adapters approved by Fluke Networks for use
with the Product to supply power to the Product
and charge the battery.
Warning: Class 1 and Class 2
Laser Products
To prevent eye damage and personal injury:
Do not look directly into optical connectors. Some
optical equipment emits invisible radiation that can
cause permanent damage to your eyes.
Do not look into the laser. Do not point laser
directly at persons or animals or indirectly off
reflective surfaces.
When you inspect fiber endfaces, use only
magnification devices that have the correct filters.
Use the Product only as specified or hazardous laser
radiation exposure can occur.
Caution
To prevent damage to the Product or cables under test and to
prevent data loss, read all safety information given in all
documentation supplied with the Product.
Connectors, Keys, and LEDs
GPU06.EPS
Figure 1. Connectors, Keys, and LEDs
LCD display with touchscreen.
Singlemode OTDR port with interchangeable SC adapter and
protective cap. The LED in front of the port turns on when the
port emits an optical signal.
Multimode OTDR port with interchangeable SC adapter and
protective cap. The LED in front of the port turns on when the
port emits an optical signal.
Visual fault locator port and protective cap. The LED in front of
the port turns on when the port emits an optical signal.
G
E
F

C
B
D
M
L
A
H
N
K
I
J

Termékspecifikációk

Márka: Fluke Networks
Kategória:
Modell: OptiFiber Pro

Szüksége van segítségre?

Ha segítségre van szüksége Fluke Networks OptiFiber Pro, tegyen fel kérdést alább, és más felhasználók válaszolnak Önnek




Útmutatók Fluke Networks

Útmutatók

Legújabb útmutatók