Használati útmutató Evapolar evaSMART EV-3000

Evapolar légkondicionáló evaSMART EV-3000

Olvassa el alább 📖 a magyar nyelvű használati útmutatót Evapolar evaSMART EV-3000 (1 oldal) a légkondicionáló kategóriában. Ezt az útmutatót 5 ember találta hasznosnak és 2 felhasználó értékelte átlagosan 4.5 csillagra

Letöltés PDF

Oldal 1/1

This equipment has been tested and found to comply with the limits for a Class B

digital device, pursuant to part 15 of the FCC Rules. These limits are designed to

provide reasonable protection against harmful interference in a residential installation.

This equipment generates, uses and can radiate radio frequency energy and, if not

installed and used in accordance with the instructions, may cause harmful interference

to radio communications. However, there is no guarantee that interference will not occur

in a particular installation. If this equipment does cause harmful interference to radio

or television reception, which can be determined by turning the equipment oﬀ and on,

the user is encouraged to try to correct the interference by one or more of the following

measures:

– Reorient or relocate the receiving antenna.

– Increase the separation between the equipment and receiver.

– Connect the equipment into an outlet on a circuit diﬀerent from that to which

the receiver is connected.

– Consult the dealer or an experienced radio/TV technician for help.

transportation” section of this product guide.

— For personal safety and proper functionality of the device use only clean,

untainted tap water. If the source of water is polluted and you are not sure

about its safety, please use distilled water. It is recommended to perform

the cleaning and technical maintenance of the device according to the

“Cleaning” section of this product guide.

— The device is not intended for use in a highly polluted environment.

Large dust particles, dirt, etc., can seriously aﬀect the longevity of the

device’s evaporative cartridge lifecycle.

— Make sure that water does not spill onto the external parts of the device.

Do not use it near water, in a swimming pool, bathroom, laundry room,

outdoors when raining or at any other location with high humidity levels.

— In the case of a leak or if water spills onto the surface of the device,

immediately disconnect the power cord and let the device dry for at least

24 hours.

— Do not place the device under direct sunlight.

— If you do not plan to use the device for a long time, empty the water

reservoir and let the device run at maximum power for at least 4 hours

to allow the cartridge to dry out.

— Use only the original power supply from the package.

— Do not touch the power supply or power cord with wet hands.

— Unplug the device during the following actions: cleaning, ﬁlling, technical

maintenance, removing/replacing elements and moving the device.

— To maximise the eﬀect the device should be placed on an elevated

surface, e.g. a table or a cupboard.

— Do not place the device next to a heater or within proximity of any

electrical equipment.

— Do not place the device in passageways or any other location from

where it will cause obstruction and can be accidentally knocked over.

— Do not let any foreign objects enter the device.

— Do not place heavy items on top of the device.

1. Slide the water reservoir up.

2. Open the lid to ﬁll up the reservoir. Fill with water.

3. Place the reservoir back onto the base. Make sure it is installed properly.

4. Use the cable to connect the device to the power source. The Power

button on the top of the device will light up. Press this button.

5. The device will switch on with a short vibration.

INTRODUCTION

Congratulations!

CONTENTS

You have bought your own personal evaSMART™ air cooler from Evapolar.

To take full advantage of the device, please install the Evapolar Mobile

Application and read the product guide before you start using it.

Intended use:

The evaSMART air cooler is designed to cool and humidify the personal

zone around you by creating a local microclimate within an area of 2 - 3 m2

(22 - 33ft2). evaSMART can be controlled via the mobile application, Smart

Home integrations or the device control panel. The best eﬀect can be

achieved indoors and in well-ventilated rooms.

Safety regulations:

— Do not install water tank with water without cartridge inside.

— The device must be placed onto a smooth horizontal surface.

Tilting it at signiﬁcant angles may cause a water leak and damage the

device.

— Remove the resevoir and set the device to run on the maximum fan

speed for at least one hour to dry the water out from the internal

reservoir before taking out the cartridge. Do not take the cartridge out

of the device unless it is done.

— Do not carry the device a long distance when it is ﬁlled with water.

Even with the empty external water reservoir, some water will still

remain in the internal one. Please refer to the “Moving and long distance

— Do not block the front and back grills of the device.

— Do not turn the device upside down; this will disrupt its functionality.

— Do not submerge the device in water or any other liquids; see cleaning

guide below.

— Do not place open ﬁre sources (candles, etc.) on top of the device.

— People with limited physical, visual or mental abilities or lacking proper

experience and/or knowledge should never use the device without the

supervision of those responsible for their safety or those capable

of assistance in using the device.

— The device can be switched oﬀ completely only when it is disconnected

from the power supply.

— The manufacturer does not bear any responsibility for any damage arising

from failure to comply with this product guide.

— A replaceable evaporative cartridge is designed speciﬁcally for this product.

To maximise the eﬀect of the device the cartridge should be changed

every 3-6 months depending on air and water conditions. If your cartridge

has been broken or damaged, you can purchase a replacement on

Evapolar.com or from your local retailer.

— Children should be supervised to ensure that they do not play with the

appliance.

o keep the device from causing any obstructions, place it slightly to one side

of your position. In this way, you will always have room for your laptop, book

or anything else needed for your activities.

Filling the reservoir

The device only needs water to work properly. You should remove the reservoir

from the left side of the device, ﬁll it with water and then place it back.

The water will start ﬂowing automatically.

The fan will stop spinning if you remove the reservoir from the device when

it is running and will resume after you put the reservoir back.

Depending on the quality of the air in the room, the full reservoir should provide

from 6 to 8 hours of uninterrupted cooling. To extend this time you need

to ﬁll up the reservoir, place it on the device, wait until the cartridge is full

of water and then reﬁll the reservoir. After this operation, the running time

will be extended by 1 to 3 hours. For instance, this may be useful if you want

to use the device whilst you sleep. The transparent reservoir lets you assess

the water level instantly. It is worth mentioning that the evaporative cartridge

will absorb up to 400 ml of water which means that once the reservoir is empty,

the device will continue cooling for another few hours. When the water runs

out completely, the device will continue working as a regular fan.

Moving and long distance transportation

Before a long distance transportation, the device should be disconnected

from the power source. In addition to the water visible in the transparent

external reservoir on the side, the device also stores some water in the internal

one so that the evaporative cartridge could absorb it. Before transportation,

it is highly recommended to:

1. Empty the water tank.

2. Set the device to run on the maximum fan speed for at least 4-5 hours

in a well-ventilated room to dry the water out from the internal reservoir

section.

Long distance transportation without drying the water out the internal

reservoir is to be attempted at your own risk. Water leakage during the

transportation is not covered by the warranty.

In order to avoid leakage, the device should be moved slowly and should

not be tilted at signiﬁcant angles.

Important: Even if there is no water in the internal reservoir, the evaporative

cartridge could still be wet. Do not transport the device on long distances with

a wet cartridge; please see “Storage during long periods of no usage” section.

For shorter distances, make sure that the device with a wet cartridge is not

isolated in a box or bag with no air ﬂow.

Temperature parameters

evaSMART Air Coolers work by using natural evaporative cooling so its

power level can change in various climates. The charts below summarize

the outgoing air temperature approximates in diﬀerent meteorologic condi-

tions in both Celsius and Fahrenheit.

6. Use the top panel of the device to adjust device parameters.

7. Install the Evapolar Mobile App to extend the evaSMART management

experience via Wi-Fi connection.

8. Connect evaSMART to Smart Home and use the full voice experience

for managing the device.

The temperature of the outgoing air will start decreasing in a few minutes.

You can vary the airﬂow intensity using the mobile app or with the arrows on

the top panel of the device. Enjoy your personal microclimate!

Important: During the ﬁrst use you may notice a technical smell.

This is normal and it will vanish completely after several hours of use.

During the ﬁrst cartridge ﬁlling there will be quick water saturation on

evaporative pads. This is normal and will enable your device to work properly.

Introduction

Safety regulations

First start

Daily use

Placing the device

Filling the reservoir

Moving and long distance transportation

Temperature parameters

Usage recommendations

Tuning

Mobile application

Smart Home

Device maintenance

Control panel & menu

Start screen

Control buttons

Menu items and working modes

Maintenance: cleaning & storage

Cleaning

Storage during long periods of no usage

Replacing the cartridge

Troubleshooting

Technical speciﬁcations

Legal information

EEE Waste

Safety instructions

DAILY USE

FIRST START

1 2

4 5

6 7 8

Usage recommendations

The device is created to be used at any location that meets the humidity

and temperature prerequisites from the previous paragraph. Minimal power

requirements allow the device to run even from a portable power bank.

Required electricity parameters: voltage 5 V, current 2,5 A and up.

Important: Due to outside conditions varying greatly, Evapolar is not responsible

for the way that the device functions outdoors.

Tuning

You can adjust the airﬂow direction and speed, alter the colour and bright-

ness level of the LED lighting and change the temperature measurement

units. All of the above is done through the Menu or mobile application and

control elements, see paragraphs on Control buttons and Menu items and

working modes.

Important:

— Make sure that the air cooler is placed on a smooth horizontal surface

to avoid leaks and spills.

— Do not use the device in temperatures exceeding 60 °C (140 °F). Failing

to do so can damage both the body and internal components of the

device.

— Allow the cartridge to completely dry out between usages.

— The air cooler performs at its best in well-ventilated premises.

— DO NOT add any aromatic oils or incenses or any other odorous sub-

stances into the water.

— To avoid water spillage, do not tilt the device at signiﬁcant angles whilst

it is ﬁlled with water; see the “Moving and long distance transportation”

section of this product guide.

— Take care when pouring water into the reservoir that is still attached to the

device as this way of ﬁlling the water reservoir up is not recommended;

do not spill water onto the body of the device.

Mobile application

The full list of device features is available through the mobile application

that is connected to the device via Wi-Fi. All of the instructions for Evapolar

mobile application usage are available in the application.

Smart Home

All of your evaSMART devices are accessible through Amazon Alexa and

Google Home. To add the device to your Smart Home environment, please

read the manual of the Home Assistant that you wish to reach.

Device maintenance

Depending on how often you use the device, its internal area needs regular

cleaning; see the "Cleaning" section of this product guide.

Start screen Control buttons

CONTROL PANEL & MENU

CLEANING

AND MAINTENANCE

Temperature of

incoming air

Temperature of

outgoing air

Power button

During the ﬁrst use evaSMART™ runs with preset default parameters.

After being used and inputting your own personal settings, the device

should run with those settings automatically.

Brightness

In this mode you can change the water reservoir brightness to your liking.

Press the Brightness button and use the arrows to change the values

between 1% and 100%. To decrease or increase the brightness quickly,

press and hold the arrow button.To turn oﬀ the water reservoir lighting, set

its brightness to 0%.

Cleaning

1. The cleaning period depends on the level of dust in the that area you

use your air cooler in.

2. Three hours prior to cleaning, empty the water from reservoir and let

the device run for a few hours without water to evaporate it from the

internal reservoir.

3. Prior to actual cleaning disconnect the device from power source.

4. Extract the cartridge (see the “Replacing the cartridge” section).

5. Wipe the internal area with a soft cloth.

6. Wash or wipe the reservoir.

7. Put the device back together; it is now ready to use or store.

Storage during long periods of no usage

Clean the device (as per instructions above), dry it and place it into an

appropriately-sized package for storage (original package is recommended).

Store the device in a dry space at temperatures 18 - 25 °C (64 - 77 °F).

Important:

— Do not put the device or the cartridge into a bag, box or any

container before it is completely dry.

— Fully replace the water in the reservoir at least once a week.

— Use a soft cloth to clean the device. Do not clean the device with

gasoline, window-washing liquid or any organic solvent. Warranty

does not cover damages caused by improper cleaning.

— Do not wipe the inside of the cartridge, just its outer plastic body.

— Do not put ﬁngers into the internal area when the device is in

operation.

1. Disconnect the device from a power source.

2. Remove the reservoir by sliding it up.

3. Pull out the safety panel to reach the cartridge.

4. Take out the old cartridge by sliding it out.

5. Place a new cartridge in place of the old one.

6. Put the safety panel back to hide the cartridge.

7. Put the reservoir back in place.

8. The device is ready to use.

Important:

— Do not install water tank with water without cartridge inside.

— Remove the reservoir and set the device to run on the maximum fan

speed for 3-4 hours to dry the water out from the internal reservoir

before taking out the cartridge. Do not take the cartridge out of the

device unless it is done.

— Depending on usage and storage, the cartridge can last 3-6 months.

— Poor water and air quality reduces the longevity of the cartridge.

— Allow the cartridge to completely dry out between usages.

— The new cartridge can be stored for up to 3 years without losing its

evaporation potential.

— Whilst replacing the cartridge, do not remove any parts other than

those described in this guide.

Colour

You can choose your preferred lighting colour for the water reservoir and adjust

its hue. Press the Colour button and use the arrows to do that. To go through

the colours quickly, press and hold the arrow button.

Brightness button

Up button

Next button

Down button

Previous button

Colour button

Fan speed button

Menu items and modes

Night mode

To enable a Night mode, press and hold the Brightness button. Both the water

reservoir lighting and screen will dim. To exit the mode, press the brightness

button.

REPLACING THE

CARTRIDGE

Problem

The device

does not turn on

The device is not connected

to power supply

Plug in

the device

There is water near

the device

The device has been pushed Wipe the water out

and dry the device

as per this guide

The device has been tilted Place it on a smooth

horizontal surface

and dry the device

as per this guide

Possible cause Solution

TROUBLESHOOTING

TECHNICAL

SPECIFICATIONS

Cold air

does not come

out of the device

The airﬂow level is on

the minimum setting

Increase the power

using the Fan speed

and Up arrow buttons

on the control panel

The temperature

drop is minimal

The device is out of water

Fill up the reservoir

The cartridge has expired Replace cartridge

The humidity level in the

room is over 70%

Ventilate the room

The device has been turned

oﬀ via the control panel

Touch and hold

the power button

Problem

Water from

the reservoir

does not reach

the evaporative

cartridge

The reservoir

has been placed

onto the device

incorrectly

Take the reservoir

out and place it

vertically onto the

device

Possible cause Solution

Wi-Fi

does not

connect

Password was input

incorrectly

Double-check

the spelling of the

password that you

have inputted

Another cause Contact us on

support.evapolar.com

to ﬁnd the solution

Power supply

Input voltage / current

Power consumption

Cooling power

Recommended cooling square/space

Water tank capacity

Water reﬁll cycle

Size

Weight (without water)

Working noise level

Energy Eﬃciency Ratio (EER)

Supplied accessories

Working conditions

100 - 240 V / 50 - 60 Hz

5 V / 2.5 A

12 W

100 – 400 W /

340 – 1360 BTU/hr

up to 3 m2 / 33 ft2

1300 ml

every 4 - 9 hours

207 x 217 x 184 mm /

7.24 x 8.14 x 8.54 inch

1820 g

25 - 40 dB

21 – 37

Cartridge

Power cord

Power adapter

Humidity <70%

Temperature >18°C

2 3

4 5

12 13

16 17

20 21

24 25

26 27

SAFETY INSTRUCTIONS

Before you use this device for the ﬁrst time, please read the following

notes and heed all warnings, even if you are familiar with handling

electronic devices. Keep these operating instructions in a safe place for

future reference. If you sell the device or give it away, pass on the user

manual at the same time. The User Manual is a part of the product.

Explanation of symbols used

DANGER! This symbol and the word "DANGER" denote a poten

tially dangerous situation. Ignoring it can lead to severe injury or

even death.

WARNING! This symbol and the word "WARNING" denote impor

tant information required for the safe operation of the product

and for the safety of its users.

WARNING! This symbol denotes danger for human health and

risk of death and/or risk of damage to equipment due to electric

shock.

Please use the supplied power adapter only to power the device.

This symbol denotes further information on the topic.

EEE WASTE

28 29

Manufacturers shall ensure that the radio equipment is accompanied by

instructions and safety information in a language which can be easily under-

stood by consumers and other end-users, as determined by the Member

State concerned. Instructions shall include the information required to use

radio equipment in accordance with its intended use. Such information shall

include, where applicable, a description of accessories and components,

including software, which allow the radio equipment to operate as intended.

Such instructions and safety information, as well as any labelling, shall be

clear, understandable and intelligible. The following information shall also be

included in the case of radio equipment intentionally emitting radio waves:

(a) frequency band(s) in which the radio equipment operates;

(b) maximum radio-frequency power transmitted in the frequency band(s) in

which the radio equipment operates.

Manufacturers shall ensure that each item of radio equipment is accompa-

nied by a copy of the EU declaration of conformity or by a simpliﬁed EU

declaration of conformity. Where a simpliﬁed EU declaration of conformity is

provided, it shall contain the exact internet address where the full text of the

EU declaration of conformity can be obtained.

In cases of restrictions on putting into service or of requirements for authori-

sation of use, information available on the packaging shall allow the identiﬁ-

cation of the Member States or the geographical area within a Member

State where restrictions on putting into service or requirements for authorisa-

tion of use exist. Such information shall be completed in the instructions

accompanying the radio equipment. The Commission may adopt imple-

menting acts specifying how to present that information. Those implement-

ing acts shall be adopted in accordance with the advisory procedure

referred to in Article 45 (2).

Application of this symbol on your equipment is conﬁrmation that you

should not dispose of this equipment in the normal household waste

stream.

In accordance with European legislation end-of-life electrical and electronic

equipment subject to disposal must be segregated household waste.

Private households within EU member states may return used electrical and

electronic equipment to designated collection facilities free of charge.

Please contact your local disposal authority for information. In some

member states, when you purchase new equipment, your local retailer may

be required to take back your old equipment free of charge. Please ask your

retailer for information.

Equipment used in a professional/business environment:

Application of this symbol on your equipment is conﬁrmation that you must

dispose of this equipment in compliance with agreed national procedures.

In accordance with European legislation end-of-life electrical and electronic

equipment subject to disposal must be managed within agreed procedures.

Prior to disposal, contact your local dealer or Evapolar representative for

end-of-life take-back information.

DANGER!

Always make sure that the device is not exposed to direct heat sources

(e.g. radiators); no direct sunlight or bright artiﬁcial light reaches the device;

contact with water sprays or drops and corrosive liquids is avoided and the

device is never operated near water; in particular the device may never be

immersed in liquids (do not place any objects containing liquids, such as

vases or drinks, on or near the device) no naked ﬂames (e.g. burning

candles) are placed on or near the device;

you keep at least 1 m of space to radio frequency and magnetic sources

(e.g. TV, speakers, mobile phones, etc.) to avoid any malfunction. In case of

malfunction, install the device at a diﬀerent place.

no foreign bodies can penetrate into the device; the device is not exposed

to any extreme temperature ﬂuctuations as this can cause moisture

through condensation and cause short circuits. If the device has been

exposed to extreme temperature ﬂuctuations, wait for it to reach the

ambient temperature before switching it on (about 2 hours) the device

should not be subjected to excessive shocks and vibrations; the device is

not covered. Heat can accumulate when the device is covered, therefore

there is a risk of ﬁre. Failure to heed the warnings above may result in

damage to the device or injury.

DANGER! Children and people with disabilities

Electrical devices are not suitable for children. Also people with reduced

physical, sensory or mental capabilities should only use electrical devices

within the limits of their abilities. Do not allow children or people with

reduced physical, sensory or mental capabilities to use electrical devices

unsupervised unless they are instructed accordingly and supervised by a

competent person responsible for their safety. Children should always be

supervised to ensure that they do not play with the product. Small parts

can cause choking hazards. Keep the packaging away from children and

people with disabilities. There is a risk of suﬀocation.

DANGER! Power adapter

Please use the supplied power adapter only to power the device.

Plug the power adapter only into a suitable and easily accessible power

socket. Do not touch the power adapter with wet hands as this could

cause an electric shock.

To unplug the power adapter from the power socket, always hold its casing

and never pull from the cable. Unplug the power adapter from the mains in

the following circumstances:

• in any dangerous situation

• if the power adapter makes an unusual noise or gives oﬀ smoke

• before a storm and/or thunderstorm

• if the power adapter is damaged

• if the power adapter has been exposed to rain or liquids

The power adapter consumes electricity even in Standby mode. In order to

completely disconnect the device from the mains, the power adapter must

be pulled out from the power socket.

Please follow these instructions to avoid risk of potential fatal injury or ﬁre!

Never cover the power adapter, otherwise there is a risk of ﬁre. Do not

attempt to open the housing of the power adapter.

This could result in potentially fatal electrocution.

WARNING! Cables

Unplug all cables by holding the plugs and never pull on the cables them-

selves. Never place pieces of furniture or other heavy objects on the cables

and take care that they do not become damaged, especially at the plugs

and sockets. Never install the cable around hot or sharp objects to avoid

damaging it. Never tie knots in cables and do not tie them to other cables.

All cables should be positioned so that nobody can trip over them or be

obstructed by them.

DANGER! Radio interface

Turn the device oﬀ when on board an aircraft, in a hospital, in an operating

theatre or in the vicinity of electronic medical equipment. The RF signals

may interfere with the functionality of sensitive devices. Keep the device at

least 20 cm (8 inches) away from pacemakers, as the RF signals could

interfere with the functionality of the pacemaker. The RF signals transmitted

can interfere with hearing aids. If the wireless mode is switched on, do not

place the device near ﬂammable gases or in a potentially explosive area

(e.g. a paint shop), as the RF signals transmitted could cause explosions or

ﬁre. The range of the radio frequency signals depends on environmental

conditions. If data is transmitted via a wireless connection, it can also be

received by unauthorised parties. Evapolar is not liable for any interference

caused to RF or TV signals through unauthorised modiﬁcation to this

device. Furthermore, Evapolar accepts no liability for replacing any cables

or devices that have not been speciﬁcally approved by Evapolar Ltd. The

user is solely responsible and liable for remedying any interference caused

by such unauthorised modiﬁcation of this device and for replacing applianc-

es.

Servicing / Repair

Repairs are required if this device is damaged in any way, for example, if the

power adapter or device housing is damaged, if liquids or objects have

entered the device or if the product has been exposed to rain or moisture.

Repairs are also necessary if the product is not working properly or has been

dropped. If you notice any smoke, unusual noise or strange smells, switch oﬀ

the device immediately and pull the power adapter out of the power socket. If

this occurs, do not continue to use the appliance and have it checked out by

an expert. All repairs must be carried out by qualiﬁed service personnel.

Operating environment

The device is not designed for use in environments with high humidity (e.g.

bathrooms) or excessive levels of dust. Operating temperature and operating

humidity: 0 to 35 °C, max. 85% relative humidity. Please note that caring

products for furniture surfaces may contain substances that can damage the

rubber feet of the device, so be careful if you have been using this type of

products.

LEGAL INFORMATION

The device complies with the requirements of EU Directives – 2014/35/EU

Low Voltage Directive and 2014/30/EU EMC Directive, as well as the

following European harmonised standards:

• EN 55014-1:2006/ A1:2009/ A2:2011 - Electromagnetic compatibility.

Requirements for household appliances, electric tools and similar

apparatus Part 1: Emission

• EN 55014-2:2015 - Electromagnetic compatibility. Requirements for

household appliances, electric tools and similar apparatus. Part 2:

Immunity. Product family standard

• EN 61000-3-2:2014 Electromagnetic compatibility (EMC). Part 3-2:

Limits. Limits for harmonic current emissions (equipment input current

≤16 A per phase)

• EN 61000-3-3:2013 Electromagnetic compatibility (EMC). Part 3-3:

Limits. Limitation of voltage changes, voltage ﬂuctuations and ﬂicker

in public low-voltage supply systems, for equipment with rated current

≤16A per phase and not subject to conditional connection

• EN 60335-1:2012/AC:2014/A11:2014 - Household and similar electrical

appliances. Safety. Part 1: General requirements

• EN 60335 -2-40:2003/ A11:2004/ A12:2005/ C1:2006/ A1:2006/

A2:2009/ C2:2010/ A13:2012/ A13/AC:2013 - Household and similar

electrical appliances. Safety. Part 2-40: Particular requirements for

electrical heat pumps, air-conditioners and dehumidiﬁers.

The device is marked by the sticker on the inner surface of the case and

contains the following data: manufacturers name \ product name \ serial

number \ year of manufacture \ power settings (voltage, frequency, maximum

power consumption, weight) \ CE marking.

We have made sure that setting up your air cooler is quick and easy.

evaSMART is almost ready-to-use right after you unpack it. All you have to do

is connect your device to Wi-Fi and add it to the mobile app and Smart Home

environment. During the following sessions your device will connect automati-

cally. Following a few simple recommendations can help to ensure that your

experience is as smooth as possible.The air cooler creates a personal comfort

zone. To be in the centre of that zone, place the device within 0.5 - 1.5 m (1.5

- 5 ft) of your position with its front grill facing you.

www.evapolar.com

At the end of its service life period

the product should be recycled according

to the recycling procedures in your region.

RECYCLING

™

Power

To switch the device on or oﬀ, press the Power button. To enable a Wi-Fi

Access point mode, press and hold the button for 3 seconds. Press the

Fan speed button to switch back.

Measurement units

For your convenience, units may either be in Celsius or in Fahrenheit.

To change the units, please press and hold a combination of the arrow

buttons (not lit) + Fan speed button or use the mobile application (Settings

section).

Factory settings restore

To restore the factory settings, enter the user settings restore menu point

ﬁrst, then press a combination of Brightness button, Colour button (these

two are not lit) and Fan speed button all at once. To exit this menu point and

get back to the main screen, press the power button. To conﬁrm the factory

settings restore, press the up button.

+ +

PRESS

18 19

3 SEC

HOLD

Sleep mode

You can set your evaSMART to turn oﬀ the fan after a speciﬁc period of time.

To enable this Sleep mode, press and hold the Fan speed button. To go through

the available time period options (from 15 minutes to 8 hours) press the Up and

Down buttons and select one of options by pressing the Fan speed button.

Colour playlists mode

To let the water reservoir lighting gradually change colours, enable a Colour

playlists mode by pressing the Colour button and holding it. To go through the

available preset lists (each has its own number) press the Up and Down

buttons and select one of the lists to play by pressing the Colour button.

Fan speed

In this mode you can change the fan speed to your liking. Press the Fan speed

button and use the arrows to change the values between 1% and 100%.

To decrease or increase the speed quickly, press and hold the arrow button.

User settings restore

To restore the user settings, press a combination of the arrow buttons (not lit)

and Power button all at once. To exit this menu point and get back to the main

screen, press the Fan speed button. To conﬁrm the user settings restore, press

the Down button.

evapolar.com/docs/evasmart

PRESS

HOLD EXIT

PRESS

HOLD CONFIRM

PRESS

HOLD CONFIRM

PRESS

SELECT

PRESS

SELECT

PRESS

SELECT

PRESS

SELECT

PRESS

+ +

PRESS

SELECT

PRESS

EXIT

PRESS

EXIT

PRESS

CONFIRM

PRESS

CONFIRM

PRESS

Full instructions are

available via the

following link:

PRODUCT GUIDE

Personal Air Cooler

evaSMART EV-3000

30%

40%

50%

60%

70%

30%

40%

50%

60%

70%

hi.evapolar.com/wiﬁ

Please ﬁnd the

instruction on

connection

establishment here:

For additional

guidance and more

information contact

Evapolar support:

support.evapolar.com

+ +

PRESS

SMART

HOME

Termékspecifikációk

Márka:	Evapolar
Kategória:	légkondicionáló
Modell:	evaSMART EV-3000

Szüksége van segítségre?

Ha segítségre van szüksége Evapolar evaSMART EV-3000, tegyen fel kérdést alább, és más felhasználók válaszolnak Önnek

Az Ön neve*

Az Ön e-mail címe*

Írja ide kérdését

Útmutatók légkondicionáló Evapolar

Evapolar evaSMART EV-3000 Útmutató

16 Augusztus 2024

Evapolar evaCHILL EV-500 Útmutató

14 Augusztus 2024

Útmutatók légkondicionáló

Legújabb útmutatók légkondicionáló

Symphony Movil 80 Útmutató

23 December 2024

Panasonic WH-SDC0509L6E5 Útmutató

23 December 2024

LG LW1011CR Útmutató

23 December 2024

LG LP0818WNR Útmutató

23 December 2024

LG LW7010HR Útmutató

23 December 2024

LG LP1220GSR Útmutató

23 December 2024

LG LW1514ER Útmutató

23 December 2024

Meireles MAC 18 W Útmutató

23 December 2024

Meireles MAC 12 W Útmutató

23 December 2024

Panasonic CS-BZ35XKE Útmutató

22 December 2024