Használati útmutató Eureka Solitaire SRS2

Eureka Fűtő Solitaire SRS2

Olvassa el alább 📖 a magyar nyelvű használati útmutatót Eureka Solitaire SRS2 (4 oldal) a Fűtő kategóriában. Ezt az útmutatót 5 ember találta hasznosnak és 2 felhasználó értékelte átlagosan 4.5 csillagra

Letöltés PDF
Oldal 1/4
• Smoke entering the room from the firebox when the door is open may be caused by
• Insufficient length of flue (Flue to be 4500mm minimum from underneath base of heater to underside of cowl)
– Increase height of flue.
• Flue Downdraught
– Consult dealer or increase height of flue.
• Creosote Build up in flue
– Remove cowl and clean flue as per cleaning instructions. Check moisture content of wood.
• Excessive ash build up
Some woods will give large amounts of ash despite how you run the heater. Others will give you very little. Use the
wood which is most convenient for you as long as it is dry. After a period of time you will get to know when to
empty your unit. Always leave 12mm of ash in the bottom of your heater. Bark will give you excessive ash. Try not to
burn it.
If you are burning wood that gives you charcoal, you may find that after running the heater say for 8 hours at
maximum burn rate, the charcoal builds up excessively. Overnight burn will reduce this charcoal back to a fine ash. If
you are not ready to shutdown for overnight burn when you next fuel the stove, load the stove with only one piece
of wood and lay it across the firebox on top of the charcoal. Open the air control wide open and you will find the
charcoal will burn down with the one piece of wood. Repeat the process until the ash level is significantly reduced.
GPN 207918
REV. D
Solitaire SRS2 Onyx Diamond Emerald Mk3 Freestanding
Solitaire SRS2, Onyx, Diamond
& Emerald Mk3 Freestanding
Operation & Installation Instructions
8
Troubleshooting (Continued)
Solitaire SRS2 Freestanding shown
1. Subject to clauses 2 & 3 of this warranty, A.F. Gason Pty Ltd ACN 004 667 556 (Gason) warrants the following components of its heaters against defects in workmanship
and/or materials for the following periods from the date of purchase:
(a) the firebox for ten years;
(b) the paint finish for a period of twelve months if the purchaser has followed the instructions provided by Gason in this Operation and Installation Instructions manual; and
(c) all other components for twelve months except the glass, fire brick lining or baffle plate if, in the opinion of Gason, these items have been damaged by impact.
2. This extended warranty does not apply:
(a) if the heater is purchased from a person who has not been authorised by Gason to sell its products;
(b) if, in the opinion of Gason, the heater or any component has been subjected to abuse, misuse, alteration, modification or has not been installed, operated or maintained in
accordance with the instructions provided by Gason; or
(c) to owners other than the original purchaser.
3. If you believe that the heater you purchased contains a manufacturing defect and you wish to make a claim under this warranty, please contact an authorised Gason service
centre to arrange for an assessment.
4. If, after assessing the heater, Gason determines that the heater contains a manufacturing fault, Gason may at its discretion:
(a) replace the heater;
(b) repair or replace specific components of the heater; or
(c) provide a full refund.
5. Parts replaced under this warranty are warranted for the balance of their original warranty period.
6. If, at the discretion of Gason, the heater or any part needs to be replaced, serviced or repaired at an authorised Gason service centre, then the person claiming under this
warranty must pay all costs associated with:
(a) returning the heater; and
(b) the delivery or collection of any new or repaired heater.
Our goods come with guarantees that cannot be excluded under the Australian Consumer Law. You are entitled to a replacement or refund for a major failure and for
compensation for any other reasonably foreseeable loss or damage. You are also entitled to have the goods repaired or replaced if the goods fail to be of acceptable quality and
the failure does not amount to a major failure.
Any benefits you receive under these warranties are in addition to other rights and remedies that you may have as a consumer under a law in relation to the heater to which
these warranties relate.
These warranties are given by:
A.F. Gason Pty Ltd
Blake Street
Ararat VIC 3322
Please contact us if you have any queries on:
Phone: 03 5352 2151;
or email us via the “Contact Us” section of our website: www.gason.com.au.
Eureka Heating reserves the right to modify or alter specifications, materials, etc. in the interest of product improvement.
WARRANTY
Solitaire SRS2 Onyx Diamond Emerald Mk3 Freestanding
7
Troubleshooting
!
WARNING
NEVER OPERATE THE HEATER WITH THE DOOR LOOSE AND NOT AIR TIGHT.
OVERFIRING COULD RESULT IN DETRIMENTAL WEAR AND TEAR ON THE
FIREBOX.
• Noisy Fan
Turn the power off and remove the three pin plug from the power point. Remove the four screws that hold the front
fan access panel. Remove the panel. Disconnect the wiring loom via the plastic joiner. Unscrew the two nuts which
hold the fan in position and remove the fan. Clean any dust with a dry paint brush and vacuum the fan blades. Clean
around the motor. After completion place two or three drops of sewing machine oil on the shafts at the bearings.
Replace the fan in reverse to the removal.
• Fan not working
Check the power connection with another appliance. If the power point is O.K. assume the Fan or the Switch is
defective. Isolate the power as above. Check that the terminals on the loom and the switch are firmly connected. If the
fan then fails to function, remove the fan and switch by firstly removing the knob off the fan switch by pulling it away
from the heater. Undo the holding nut and pull the switch out. Disconnect the wiring from the power lead and remove
the fan and switch. Convey the same to the authorised Eureka Dealer from whom you purchased your unit for service.
Replace in the reverse order.
• Air Control Jamming
Remove air control cover plate by removing the four screws which hold it onto the face of the heater. There are two bolts
holding the air slide in place. Undo them and remove the air slide. Wipe any ash or dust that may have accumulated on
the back of the air slide or on the face of the heater. If any burrs have developed on the back of the air slide or on the
face of the heater, rub them off with fine wet and dry sand paper till you have a smooth surface and edges. Replace the
air slide and make sure the washers and spacers are on the bolts when you screw the bolts back into the face of the
heater. Do not apply any type of lubricant to the air slide whatsoever as this will attract dust and make the slide stick.
• No Overnight Burn
Remove the air slide as per air control jamming and check that the air slide is hard against the face of the heater. If it is
loose, tighten up the bolts holding the air slide to the face of the heater. Do not overtighten.
Check that the door rope has an even indentation from the sealing strip, which is on the face of the firebox. If it is uneven
and it appears as though air could leak through the seal, adjust the thickness of the door rope to suit. Stretch the rope to
make it thinner where the indentation is the heaviest and bunch up the excess where the indentation is smaller.
Check the four bolts that hold the glass retainer in position. If loose tighten. Do not overtighten.
The door may become loose through the door seal shrinking. To tighten the door, open the door and look at the inside of
the door catch. Undo the nut which is holding the latch plate. Remove the latch plate. Remove one thick washer and the
star washer. Refit the latch plate. The latch plate is concave to provide a lead in edge so that there is smooth connection
between the door latch and the catch. Make sure that the face of the latch that is curved outward is facing towards the
door.
Replace the nut. When closing the door you should now feel firm resistance when the latch comes into contact with the
catch.
Overfiring
Solitaire SRS2 Onyx Diamond Emerald Mk3 Freestanding
2
!
WARNING
Read and follow these instructions carefully before installing and
using this appliance.
SAVE THESE INSTRUCTIONS
Paint curing and care
!
WARNING
• A flue fire with resulting damage may occur if this appliance is not installed,
operated and maintained as per this booklet.
• Never place combustible material such as wood, paper or furniture near the
appliance.
• This appliance is designed to burn dry wood. Do not burn rubbish, driftwood,
flammable liquids or any substance containing salts or corrosives.
• This appliance must not be installed and operated in an area where kerosene,
petrol, paint thinner or other flammable liquid is used or stored.
• The flue system must be inspected and cleaned annually or sooner if required.
Failure to do so could result in an excessive build up of creosote which may
result in a flue fire which may damage the flue or cause damage to your
home.
• The surface of the appliance becomes hot during operation. Do not touch the
surface of this appliance. Keep children away from the appliance during
operation. Do not allow anyone to operate this appliance who is not familiar
with the instructions in this booklet.
!
WARNING
Your heater is coated with the best available heat resistant paint. Even though
the paint has been baked after application, it may require further temperature
curing. It may, if you overfire the heater on its first fire, discolour. For your first
two or three firings, never exceed medium air setting and always have the fan on
when above low burn. Do not wipe the heater while the paint is curing. After the
paint has cured the only maintenance required to maintain the heaters finish is to
wipe it with a soft cloth. Do not use any commercial cleaners or solvents on the
paint finish.
We are proud of the presentation of our products. If at any time you need to
freshen up the paint finish, your local dealer has touch up paint available for
purchase. You may even change the colour of your heater if you wish.
If you have any enquires, please contact the dealer from whom you purchased your heater:
PLEASE COMPLETE:
Dealer Name
Dealer Address
Phone
Please attach your original purchase dockets to this booklet for future reference.
Safety Warnings
Solitaire SRS2 Onyx Diamond Emerald Mk3 Freestanding
6
Solitaire SRS2 Onyx Diamond Emerald Mk3 Freestanding
3
Operating your Eureka (Continued)
Overnight burn
Approximately 30 minutes before turning the heater down to overnight burn it is recommended to load the heater with
fuel for the overnight burn. Leave the air control in the medium to high position. Let the heater run for about thirty
minutes. This will reduce the moisture content in the fuel before shut down. (This will help reduce the creosote formation
in the firebox and flue.) Set the air control to the setting you have found best for your requirements which is normally
about 8mm to the right of full shut down. Turn the fan off and retire. The aim when overnight burning is to have only a
few hot embers left in the bottom of the firebox in the morning. Not huge lumps of wood.
Cleaning your flue
Carefully remove baffle plate and put it to one side. Close the heater door. Obtain a flue brush (Solitaire SRS2 178mm,
Onyx/Diamond/Emerald Mk3 150mm) from your local Eureka Dealer and proceed up onto your roof. Remove the cowl.
Slowly push the flue brush down the chimney until it stops. Pull the brush back out and repeat the process. Each time you
do this you will notice that the brush will go further down the chimney till it reaches the bottom. The soot and creosote
will fall down the chimney and into the firebox. Clean residue from firebox. Replace the baffle plate. Make sure you do
the job well. The cleaner the flue the less chance there will be of the creosote sticking again. After you have replaced the
cowl, inspect the roof flashing for any damage that may have been incurred whilst you were cleaning the flue. Reseal the
seal on the roof with roof and gutter silicone if required.
The fan
It is recommended to run the fan while the heater is operating above low burn on low speed. For extended periods when
the heater is running above medium fire, high or boost is recommended. Boost is recommended for short bursts where a
quick temperature rise is desired in conjunction with a high fire setting. The fan should be cleaned on a regular basis.
(Refer Troubleshooting for fan removal and cleaning.)
!
WARNING
Leaving Door Open
As stated previously in relation to leaving door open 25mm to encourage the fire
to pick up at a faster rate. Your heater has been tested to ensure that no
structural damage can take place if the door is inadvertently left open. However
your paint finish can be damaged if the door is left open for a long period with a
full firebox of fuel with the fan off. Closely supervise your heater while the door is
left open.
Closing the Door
Always ensure that before you close your door there is no wood protruding
beyond the front of the firebox opening. Do not use the door glass as a ’battering
ram’ to push the wood back into the firebox. Damage to the glass by such
impact is not covered by your warranty.
The Door
Installation
!
WARNING
THE INSTALLATION OF THIS APPLIANCE MUST BE CARRIED OUT AS PER THIS
MANUAL AND THE FLUE MANUFACTURERS SPECIFICATIONS.
WE RECOMMEND THAT YOU USE A QUALIFIED INSTALLER TO CARRY OUT
THE INSTALLATION.
If you have any other enquiries, please contact the dealer from whom you
purchased your heater.
THIS APPLIANCE WEIGHS IN EXCESS OF 170 KILOGRAMS. EXTREME CARE
SHOULD BE TAKEN WHEN HANDLING THE APPLIANCE.
Clearances to combustibles & flue requirements
It is recommended that you either use the flue kit that was tested in test report numbers shown below, or an approved
Australian Standard flue kit, (that incorporates a decorative surround which is unperforated for 180 degrees of its
circumference) in conjunction with the original test report.
The Eureka Solitaire SRS2, Onyx, Diamond & Emerald Mk3 have been tested to the Australian Standard 2918:1990 Appendix B.
• SOLITAIRE SRS2: Report RF/95/091.
•
ONYX: Report HCU/98/005 . A
• DIAMOND: Report RF/95/097.
• EMERALD Mk3: Report HCU/96/116.
The Solitaire SRS2, Onyx, Diamond and Emerald Mk3 Freestanding heaters conform to the Australian Standard in the
following placement of the appliance in relation to combustible surfaces.
Rear Wall
(Solitaire SRS2) 50mm
(Onyx) 50mm
(Diamond) 25mm
(Emerald Mk 3) 125mm
(Solitaire SRS2) 50mm
(Onyx) 50mm
(Diamond) 25mm
(Emerald Mk 3) 125mm
Side Wall
Rear Wall
(Solitaire SRS2) 100mm
(Onyx) 100mm
(Diamond) 100mm
(Emerald Mk3) 150mm
(Solitaire SRS2) 350mm
(Onyx) 330mm
(Diamond) 300mm
(Emerald Mk3) 450mm
Side Wall
Floor Protector
Floor Protector
Installation
SOLITAIRE SRS2:The Solitaire SRS2 conforms to A.S. 2918:1990 when placed in the above position on a minimum
hearth or floor protector of 1170 mm deep x 975mm wide x 7.5mm thickness. The floor protector should extend
400mm in front of the appliance base.
ONYX: The Onyx conforms to when placed in AS/NZS 2918:2018 the above position on a minimum hearth or floor
protector of 1020 mm deep x 1170 mm wide x 4 mm thickness. The floor protector should extend 300mm in front of
the appliance base.
DIAMOND:The Diamond conforms to A.S. 2918:1990 when placed in the above position on a minimum hearth or floor
protector of 1070mm deep x 910mm wide x 7.5mm thickness. The floor protector should extend 350mm in front of the
appliance base.
EMERALD MK3: The Emerald Mk3 conforms to when placed in the above position on a AS/NZS 2918:2018
minimum hearth or floor protector of 1070 mm deep x 900 mm wide x 4.5 mm thickness. The floor protector
should extend 300mm in front of the appliance base.
Hearth Requirements
Operation of the Fan
!
WARNING
If firebox failure is reported and it is found that the firebox has been abused
through improper use of the fan, Eureka reserve the right to disallow any
warranty claims in relation to firebox failure.

Termékspecifikációk

Márka: Eureka
Kategória: Fűtő
Modell: Solitaire SRS2

Szüksége van segítségre?

Ha segítségre van szüksége Eureka Solitaire SRS2, tegyen fel kérdést alább, és más felhasználók válaszolnak Önnek


Útmutatók Fűtő Eureka

Eureka

Eureka Stockade SRS5 Insert Útmutató

19 Augusztus 2024
Eureka

Eureka Opal SRS4 Insert Útmutató

19 Augusztus 2024
Eureka

Eureka Garnet SRS3 Insert Útmutató

19 Augusztus 2024
Eureka

Eureka Opal SRS3 Freestanding Útmutató

8 Augusztus 2024
Eureka

Eureka Garnet SRS2 Freestanding Útmutató

7 Augusztus 2024
Eureka

Eureka Jewel Freestanding Útmutató

7 Augusztus 2024
Eureka

Eureka Solitaire SRS2 Útmutató

26 Július 2024
Eureka

Eureka Ruby Freestanding Útmutató

17 Július 2024
Eureka

Eureka Pearl Insert Útmutató

16 Július 2024
Eureka

Eureka Ruby Insert Útmutató

13 Július 2024

Útmutatók Fűtő

Legújabb útmutatók Fűtő

Dimplex

Dimplex VFMi 60C Útmutató

6 Április 2025
Scandia

Scandia Styliste’ 6 Útmutató

4 Április 2025
Einhell

Einhell MR 7 S Útmutató

30 Március 2025
Argoclima

Argoclima Dori Night Útmutató

30 Március 2025
Dimplex

Dimplex 2NC81524L Útmutató

30 Március 2025
Dimplex

Dimplex FXL24i Útmutató

30 Március 2025
DeLonghi

DeLonghi RHJ21F1015 Útmutató

27 Március 2025
Rinnai

Rinnai GEPH-22DTW Útmutató

27 Március 2025
Einhell

Einhell NKH 1500 Útmutató

27 Március 2025
Einhell

Einhell NBH 2000 H Útmutató

27 Március 2025