Használati útmutató Epcom X6262A

Epcom nincs kategorizálva X6262A

Olvassa el alább 📖 a magyar nyelvű használati útmutatót Epcom X6262A (2 oldal) a nincs kategorizálva kategóriában. Ezt az útmutatót 5 ember találta hasznosnak és 2 felhasználó értékelte átlagosan 4.5 csillagra

Letöltés PDF

Oldal 1/2

Page 1 of 2

Installation and Operation Instructions

LED Beacons

Specications:

Size: 3.8”(D) x 2.8”(W) x 4.9”(H)

Weight: 0.8 lb.

Current draw: 0.5 Amps max. (@+12.8VDC)

Locate the unit in the desired position on a at mounting surface, and

using the base as a template, mark the two mounting hole locations.

Drill the holes using a 7/32” (0.219”) drill size. Drill a third hole,

exterior to the base to serve as a wire access hole. Mount the unit

using #10 hardware.

Installation & Mounting:

Flush Mount:

Pipe Mount:

Carefully remove the LED beacon from packaging. Examine the unit for

transit damage. If damage is found, return product to your local dealer for

warranty replacement. Do not use damaged or broken parts.

Maintenance-free LED Beacons feature the latest

LEDs and a Pulse8 ash pattern, producing a warning

signal ideally suited to industrial applications. This

cost effective unit has a wide operating range of

12-80V, making it the perfect light for use on electric

vehicles.

1. Proper installation combined with operator training in the use, care, and maintenance of emergency warning devices are essential to ensure

the safety of you and those you are seeking to protect.

2. Exercise caution when working with live electrical connections.

3. This product must be properly grounded. Inadequate grounding and/or shorting of electrical connections can cause high current arcing,

which can cause personal injury and/or severe vehicle damage, including re.

4. Proper placement and installation are vital to the performance of this warning device. Install this product so that output performance of the

system is maximized and the controls are placed within convenient reach of the operator so that s/he can operate the system without losing

eye contact with the roadway.

5. Do not install this product or route any wires in the deployment area of an air bag. Equipment mounted or located in an air bag deployment

area may reduce the effectiveness of the air bag or become a projectile that could cause serious personal injury or death. Refer to the

vehicle owner’s manual for the air bag deployment area. It is the responsibility of the user/operator to determine a suitable mounting location

ensuring the safety of all passengers inside the vehicle particularly avoiding areas of potential head impact.

6. It is the responsibility of the vehicle operator to ensure during use that all features of this product work correctly. In use, the vehicle operator

should ensure the projection of the warning signal is not blocked by vehicle components (i.e., open trunks or compartment doors), people,

vehicles or other obstructions.

7. The use of this or any other warning device does not ensure all drivers can or will observe or react to a warning signal. Never take the right-

of-way for granted. It is your responsibility to be sure you can proceed safely before entering an intersection, driving against trafc, respond-

ing at a high rate of speed, or walking on or around trafc lanes.

8. This equipment is intended for use by authorized personnel only. The user is responsible for understanding and obeying all laws regarding

warning signal devices. Therefore, the user should check all applicable city, state, and federal laws and regulations. The manufacturer as-

sumes no liability for any loss resulting from the use of this warning device.

Do not install and/or operate this safety product unless you have read and understand the safety information

contained

Failure to install or use this product according to manufacturer’s recommendations may result in property damage, serious injury, and/or death to

those you are seeking to protect!

WARNING!

Caution: When drilling into any vehicle surface, make sure the area

is free from any electrical wires, fuel lines, vehicle upholstery, etc. that

could be damaged

1. Larger wires and tight connections will provide longer service life for components. For high current wires it is highly recommended that terminal blocks or

soldered connections be used with shrink tubing to protect the connections. Do not use insulation displacement connectors (e.g., 3M Scotchlock type con-

nectors).

2. Route wiring using grommets and sealant when passing through compartment walls. Minimize the number of splices to reduce voltage drop. High ambient

temperatures (e.g., under-hood) will signicantly reduce the current carrying capacity of wires, fuses, and circuit breakers. All wiring should conform to the

minimum wire size and other recommendations of the manufacturer and be protected from moving parts and hot surfaces. Looms, grommets, cable ties, and

similar installation hardware should be used to anchor and protect all wiring.

3. Fuses or circuit breakers should be located as close to the power takeoff points as possible and properly sized to protect the wiring and devices.

4. Particular attention should be paid to the location and method of making electrical connections and splices to protect these points from corrosion and loss of

conductivity.

5. Ground termination should only be made to substantial chassis components, preferably directly to the vehicle battery.

6. Circuit breakers are very sensitive to high temperatures and will “false trip” when mounted in hot environments or operated close to their capacity.

920-6201-01 Rev. A Page 2 of 2

WARNING!

The LED beacon power supply is a high voltage device. To avoid the risk of

electrical shock, turn off power before removing lens. There are no internally

serviceable parts.

Important: Disable power before wiring up the LED beacon.

The unit is designed for electrical systems from 12 to 80 VDC (9 to 86 VDC

extremes). The wiring for all systems is:

Red Wire Positive (+)

Black Wire Negative (-)

All wiring should be a minimum of 18 AWG. A 3-amp fuse in the positive line is

required (see Figure 1). A switch may be used to control the on/off function of

the LED beacon. Note: For model 6263, wires will come from bottom, not side as

Figure 1 shows. Still follow same wiring instructions.

1. Most LED beacon failures, including intermittent or erratic operation as well

as failure of operation can be traced to wiring or battery problems. Check

all wiring, connections, fuse, switch, and battery voltage to insure that the

correct voltage is reaching the LED beacon.

2. If this has not remedied the problem, return product to your local dealer for

warranty replacement.

Wiring Instructions:

Maintenance & Troubleshooting:

NOTE: THIS UNIT IS REVERSE POLARITY PROTECTED

AND WILL NOT OPERATE IF WIRED B ACKWARD.

Description Part Number

Lens, 4” R6260LX*

Lens Gasket R6220GL

Branch Guard A6200BG

*where X indicates color: A = Amber, B = Blue, C = Clear, G = Green,

R = Red

Replacement Parts & Accessories:

Figure 1

NOTE: Operating the vehicle without the outer lens installed on the product may result in damage that will NOT be covered under warranty.

Manufacturer Limited Warranty and Limitation of Liability:

Manufacturer warrants that on the date of purchase, this product will conform to Manufacturer’s specications for this product (which are

available from the Manufacturer upon request). This Limited Warranty extends for thirty-six (36) months from the date of purchase.

DAMAGE TO PARTS OR PRODUCTS RESULTING FROM TAMPERING, ACCIDENT, ABUSE, MISUSE, NEGLIGENCE, UNAPPROVED

MODIFICATIONS, FIRE OR OTHER HAZARD; IMPROPER INSTALLATION OR OPERATION; OR NOT BEING MAINTAINED IN ACCOR-

DANCE WITH THE MAINTENANCE PROCEDURES SET FORTH IN MANUFACTURER’S INSTALLATION AND OPERATING INSTRUC-

TIONS VOIDS THIS LIMITED WARRANTY.

Exclusion of Other Warranties:

MANUFACTURER MAKES NO OTHER WARRANTIES, EXPRESSED OR IMPLIED. THE IMPLIED WARRANTIES FOR MERCHANT-

ABILITY, QUALITY OR FITNESS FOR A PARTICULAR PURPOSE, OR ARISING FROM A COURSE OF DEALING, USAGE OR TRADE

PRACTICE ARE HEREBY EXCLUDED AND SHALL NOT APPLY TO THE PRODUCT AND ARE HEREBY DISCLAIMED, EXCEPT TO

THE EXTENT PROHIBITED BY APPLICABLE LAW. ORAL STATEMENTS OR REPRESENTATIONS ABOUT THE PRODUCT DO NOT

CONSTITUTE WARRANTIES.

Remedies and Limitation of Liability:

MANUFACTURER’S SOLE LIABILITY AND BUYER’S EXCLUSIVE REMEDY IN CONTRACT, TORT (INCLUDING NEGLIGENCE), OR

UNDER ANY OTHER THEORY AGAINST MANUFACTURER REGARDING THE PRODUCT AND ITS USE SHALL BE, AT MANUFAC-

TURER’S DISCRETION, THE REPLACEMENT OR REPAIR OF THE PRODUCT, OR THE REFUND OF THE PURCHASE PRICE PAID BY

BUYER FOR NON-CONFORMING PRODUCT. IN NO EVENT SHALL MANUFACTURER’S LIABILITY ARISING OUT OF THIS LIMITED

WARRANTY OR ANY OTHER CLAIM RELATED TO THE MANUFACTURER’S PRODUCTS EXCEED THE AMOUNT PAID FOR THE

PRODUCT BY BUYER AT THE TIME OF THE ORIGINAL PURCHASE. IN NO EVENT SHALL MANUFACTURER BE LIABLE FOR LOST

PROFITS, THE COST OF SUBSTITUTE EQUIPMENT OR LABOR, PROPERTY DAMAGE, OR OTHER SPECIAL, CONSEQUENTIAL,

OR INCIDENTAL DAMAGES BASED UPON ANY CLAIM FOR BREACH OF CONTRACT, IMPROPER INSTALLATION, NEGLIGENCE, OR

OTHER CLAIM, EVEN IF MANUFACTURER OR A MANUFACTURER’S REPRESENTATIVE HAS BEEN ADVISED OF THE POSSIBILITY

OF SUCH DAMAGES. MANUFACTURER SHALL HAVE NO FURTHER OBLIGATION OR LIABILITY WITH RESPECT TO THE PRODUCT

OR ITS SALE, OPERATION AND USE, AND MANUFACTURER NEITHER ASSUMES NOR AUTHORIZES THE ASSUMPTION OF ANY

OTHER OBLIGATION OR LIABILITY IN CONNECTION WITH SUCH PRODUCT.

This Limited Warranty denes specic legal rights. You may have other legal rights which vary from jurisdiction to jurisdiction. Some jurisdic-

tions do not allow the exclusion or limitation of incidental or consequential damages.

www.syscom.mx

Termékspecifikációk

Márka:	Epcom
Kategória:	nincs kategorizálva
Modell:	X6262A

Szüksége van segítségre?

Ha segítségre van szüksége Epcom X6262A, tegyen fel kérdést alább, és más felhasználók válaszolnak Önnek

Az Ön neve*

Az Ön e-mail címe*

Írja ide kérdését

Útmutatók nincs kategorizálva Epcom

Epcom X67-R Útmutató

27 Augusztus 2024

Epcom X303N Útmutató

27 Augusztus 2024

Epcom XLL-1088-RB Útmutató

27 Augusztus 2024

Epcom GT-003 Útmutató

27 Augusztus 2024

Epcom X12BW Útmutató

27 Augusztus 2024

Epcom X7945A Útmutató

27 Augusztus 2024

Epcom XLS-100 Útmutató

27 Augusztus 2024

Epcom X3225 Útmutató

27 Augusztus 2024

Epcom X606-A Útmutató

27 Augusztus 2024

Epcom X6262A Útmutató

27 Augusztus 2024

Útmutatók nincs kategorizálva

Legújabb útmutatók nincs kategorizálva

Roland SD-20 Útmutató

16 Október 2024

SilverCrest SRG 1300 C3 Útmutató

16 Október 2024

IFM TY0058 Útmutató

16 Október 2024

Thule Kit 186039 Útmutató

16 Október 2024

Blumfeldt Solidflor Útmutató

16 Október 2024

Dimplex QRAD200E Útmutató

16 Október 2024

DAS Audio AX-112-5 Útmutató

16 Október 2024

Ferplast Ergocomfort Freetime Útmutató

16 Október 2024

AEG MECK52 Útmutató

16 Október 2024

Black Diamond BD1121530000ALL1 Útmutató

16 Október 2024