Használati útmutató Epcom X3225

Epcom nincs kategorizálva X3225

Olvassa el alább 📖 a magyar nyelvű használati útmutatót Epcom X3225 (9 oldal) a nincs kategorizálva kategóriában. Ezt az útmutatót 5 ember találta hasznosnak és 2 felhasználó értékelte átlagosan 4.5 csillagra

Letöltés PDF

Oldal 1/9

Specications:

Model Length LEDs Watts Amps/12

VDC

Amps/24

VDC Lumens Fuse

Needed

EW3108-F 8” 6 30 3.3 1.1 1680 5

EW3108-S 8” 6 30 3.2 1 1680 5

EW3114 14” 12 60 5.7 2.1 3360 7.5

EW3124 24” 21 105 8.7 3.6 5880 10

EW3136 36” 33 165 13 6.6 9240 15

EW3149 49” 45 225 18.5 7.9 12600 25

EW3208-F 8” 12 60 4.5 2.2 3360 7.5

EW3208-S 8” 12 60 4.7 2.3 3360 7.5

EW3214 14” 24 120 9.3 4.5 6720 15

EW3225 25” 44 220 17.3 8.4 12320 20

EW3233 33” 60 300 25 12 16800 30

EW3242 42” 76 380 32 15.5 21280 40

EW3312-F 12” 6 60 4.4 2.1 3350 5

EW3312-S 12” 6 60 4.4 2.1 3350 5

EW3324 24” 12 120 7.9 3.9 8400 10

EW3336 36” 18 180 12 5.8 12600 15

IMPORTANT! Read all instructions before installing and using. Installer: This manual must be

delivered to the end user.

Do not install and/or operate this safety product unless you have read and understand the safety

information contained in this manual.

1. Proper installation combined with operator training in the installation, use, care and maintenance of vehicle equipment accessories is

essential to ensure the safety of you and those you are trying to protect.

2. Exercise caution when working with live electrical connections.

3. This product must be properly grounded. Inadequate grounding and/or shorting of electrical connections can cause high

current arcing, which can cause personal injury and/or severe vehicle damage, including re.

4. Proper placement and installation are vital to the performance of this worklamp. Install this product so that output

performance of the system is maximized and the controls are placed within convenient reach of the operator so that s/he can

operate the system without losing eye contact with the work area.

5. It is the responsibility of the vehicle operator to ensure during use that all features of this product work correctly. In use, the

vehicle operator should ensure the projection of the beam is not blocked by vehicle components (i.e., open trunks

or compartment doors), people, vehicles, or other obstructions.

6. The manufacturer assumes no liability for any loss resulting from the use of this device.

WARNING!

Failure to install or use this product according to manufacturer’s recommendations may result in property

damage, serious bodily/personal injury, and/or death to you and those you are seeking to protect! Check wattage

before installing light to avoid possible equipment damage.

SAA

NOTE: Black die cast Aluminum housing gets very hot to the touch after operating constantly for several hours.

Installation and Operation Instructions

LED UTILITY BARS

ECCO LED Utility Bars are designed to provide superior lighting performance and withstand the harshest environments. Avail-

able in various lengths, LED wattages, and with either ood, spot or combination beam patterns. These robust, high output

lights feature the latest LEDs and reectors designed for maximum light projection. The coated die-cast aluminum housing is

fully sealed for protection against water ingress, vibration, shock and impact. Two (pivoting) mounting methods are included,

choose from heavy duty side-mounted pedestal brackets or bottom-mounted carriage bolts. Additional benets of LED tech-

nology include a bright white beam, low current consumption and a long, maintenance free service life. This manual provides

information about installation, function, safety, maintenance, replacement parts, and warranty.

920-0406-00 Rev. D Page 1 of 9

Pedestal Mount

Pivot Mount

Installation (Pedestal Mount):

1. Attach the bolt through the hole and side bracket using

the spring locking bolt. See Figure 1.

2. Select a mounting surface to match the diameter of the

included bracket(s).

3. Put the shockproof pad on the mounting plate, then feed

the hexagon bolt through the side of the bracket. Put the

plain washers and locking spring washer on the bolt, then

fasten it. See Figure 2.

4. Connect the power line to the corresponding power

connector.

5. Adjust beam location of the unit and tighten the lock nut

with a wrench.

920-0406-00 Rev. D Page 2 of 9

Installation (Pivot Mount):

1. First, put hexagon bolt through movable bracket,

shockproof pad and the bracket, then fasten hex nut. See

Figure 3.

2. Put two nished brackets into the bottom of bracket round

bar, then adjust these two brackets in proper position, then

fasten it. See Figure 4.

3. Put hexagon bolt through bracket and mounting plate,

then put spring meson, then fasten nut. See Figure 5.

4. Connect the power line to the corresponding power

connector.

Figure 1

Figure 2

Figure 3

Figure 4

Figure 5

Manufacturer Limited Warranty and Limitation of Liability:

Manufacturer warrants that on the date of purchase this product will conform to Manufacturer’s specications for this product (which are available from the

Manufacturer upon request), and Manufacturer further warrants that this product is free from defects in materials and workmanship. This Limited Warranty

extends for 36 months from the date of purchase. Other warranties may apply, call Manufacturer for details. Manufacturer will, at its discretion, repair or

replace any product found by the Manufacturer to be defective and subject to this Limited Warranty.

DAMAGE TO PARTS OR PRODUCTS RESULTING FROM TAMPERING, ACCIDENT, ABUSE, MISUSE, NEGLIGENCE, UNAPPROVED MODIFICATIONS, FIRE OR

OTHER HAZARD; IMPROPER INSTALLATION OR OPERATION; OR NOT BEING MAINTAINED IN ACCORDANCE WITH THE MAINTENANCE PROCEDURES SET

FORTH IN MANUFACTURER’S INSTALLATION AND OPERATING INSTRUCTIONS VOIDS THIS LIMITED WARRANTY.

ORAL STATEMENTS OR REPRESENTATIONS ABOUT THE PRODUCT WHICH MAY HAVE BEEN MADE BY SALESPEOPLE, DEALERS, AGENTS OR OTHER

MANUFACTURER’S REPRESENTATIVES DO NOT CONSTITUTE WARRANTIES. THIS LIMITED WARRANTY MAY NOT BE AMENDED, MODIFIED, OR EN-

LARGED EXCEPT BY A WRITTEN AGREEMENT SIGNED BY AN AUTHORIZED OFFICIAL OF MANUFACTURER WHICH EXPRESSLY REFERS TO THIS LIMITED

WARRANTY.

Exclusion of Other Warranties: MANUFACTURER MAKES NO OTHER WARRANTIES, EXPRESS OR IMPLIED. THE IMPLIED WARRANTIES

FOR MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE ARE HEREBY EXCLUDED AND SHALL NOT APPLY TO THE PRODUCT. BUYER’S SOLE

AND EXCLUSIVE REMEDY IN CONTRACT, TORT, OR UNDER ANY OTHER THEORY AGAINST MANUFACTURER REGARDING THE PRODUCT AND ITS USE

SHALL BE THE REPLACEMENT OR REPAIR OF THE PRODUCT AS DESCRIBED ABOVE.

Limitation of Liability: IN THE EVENT OF LIABILITY FOR DAMAGES ARISING OUT OF THIS LIMITED WARRANTY OR ANY OTHER CLAIM

RELATED TO THE MANUFACTURER’S PRODUCTS, MANUFACTURER’S LIABILITY FOR DAMAGES SHALL BE LIMITED TO THE AMOUNT PAID FOR THE

PRODUCT AT THE TIME OF THE ORIGINAL PURCHASE. IN NO EVENT SHALL MANUFACTURER BE LIABLE FOR LOST PROFITS, THE COST OF SUBSTITUTE

EQUIPMENT OR LABOR, PROPERTY DAMAGE, OR OTHER SPECIAL, CONSEQUENTIAL, OR INCIDENTAL DAMAGES BASED UPON ANY CLAIM FOR BREACH

OF CONTRACT, IMPROPER INSTALLATION, NEGLIGENCE, OR OTHER CLAIM, EVEN IF MANUFACTURER OR A MANUFACTURER’S REPRESENTATIVE HAS

BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. MANUFACTURER SHALL HAVE NO FURTHER OBLIGATION OR LIABILITY WITH RESPECT TO THE

PRODUCT OR ITS SALE, OPERATION AND USE, AND MANUFACTURER NEITHER ASSUMES NOR AUTHORIZES THE ASSUMPTION OF ANY OTHER OBLIGA-

TION OR LIABILITY IN CONNECTION WITH SUCH PRODUCT.

This Limited Warranty denes specic legal rights. You may have other legal rights which vary from state to state. Some states do not allow the exclusion or

limitation

Wiring Instructions:

Black Wire: Ground

Red Wire: Connect to fused power

833 West Diamond St

Boise, Idaho 83705

Customer Service

USA 800-635-5900

UK +44 (0)113 237 5340

AUS +61 (0)3 63322444

www.eccogroup.com

920-0406-00 Rev. D Page 3 of 9