Használati útmutató Dremel 300 Series

Dremel Csavaros gép 300 Series

Olvassa el alább 📖 a magyar nyelvű használati útmutatót Dremel 300 Series (72 oldal) a Csavaros gép kategóriában. Ezt az útmutatót 6 ember találta hasznosnak és 2 felhasználó értékelte átlagosan 4.5 csillagra

Letöltés PDF
Oldal 1/72
Instructional Safety
Manual
300 Series
High Speed Rotary Tool
Form No. 2610925781 05/05 Robert Bosch Tool Corporation © 2004
All Rights Reserved
1-800-437-3635
http://www.dremel.com
Dremel brand products are manufactured and sold by the
Dremel Division of Robert Bosch Tool Corporation
DM 2610925781 5-05.qxd 5/12/05 10:31 PM Page 1
2
Read all instructions. Failure to follow all instructions listed below
may result in electric shock, fire and/or serious injury. The term “power
tool” in all of the warnings listed below refers to your mains-operated (corded) power tool
or battery-operated (cordless) power tool.
SAVE THESE INSTRUCTIONS
Work area safety
Keep work area clean and well lit.
Cluttered or dark areas invite accidents.
Do not operate power tools in explosive
atmospheres, such as in the presence of
flammable liquids, gases or dust. Power
tools create sparks which may ignite the
dust or fumes.
Keep children and bystanders away
while operating a power tool. Distractions
can cause you to lose control.
Electrical safety
Power tool plugs must match the outlet.
Never modify the plug in any way. Do not
use any adapter plugs with earthed
(grounded) power tools. Unmodified plugs
and matching outlets will reduce risk of elec-
tric shock.
Avoid body contact with earthed or
grounded surfaces such as pipes, radia-
tors, ranges and refrigerators. There is an
increased risk of electric shock if your body
is earthed or grounded.
Do not expose power tools to rain or wet
conditions. Water entering a power tool will
increase the risk of electric shock.
Do not abuse the cord. Never use the
cord for carrying, pulling or unplugging
the power tool. Keep cord away from
heat, oil, sharp edges or moving parts.
Damaged or entangled cords increase the
risk of electric shock.
When operating a power tool outdoors,
use an extension cord suitable for out-
door use. Use of a cord suitable for outdoor
use reduces the risk of electric shock.
Do not use AC only rated tools with a DC
power supply. While the tool may appear
to work, the electrical components of the AC
rated tool are likely to fail and create a haz-
ard to the operator.
If operating the power tool in damp loca-
tions is unavoidable a Ground Fault
Circuit Interrupter (GFCI) must be used
to supply the power to your tool. GFCI
and personal protection devices like electri-
cian’s rubber gloves and footwear will fur-
ther enhance your personal safety.
Personal safety
Stay alert, watch what you are doing and
use common sense when operating a
power tool. Do not use a power tool
while you are tired or under the influence
of drugs, alcohol or medication. A
moment of inattention while operating
power tools may result in serious personal
injury.
Use safety equipment. Always wear eye
protection. Safety equipment such as dust
mask, non-skid safety shoes, hard hat, or
hearing protection used for appropriate con-
ditions will reduce personal injuries.
Avoid accidental starting. Ensure the
switch is in the off-position before plug-
ging in. Carrying power tools with your fin-
ger on the switch or plugging in power tools
that have the switch on invites accidents.
Remove any adjusting key or wrench
before turning the power tool on. A
wrench or a key left attached to a rotating
part of the power tool may result in person-
al injury.
Do not overreach. Keep proper footing
and balance at all times. This enables bet-
ter control of the power tool in unexpected
situations.
Dress properly. Do not wear loose cloth-
ing or jewelry. Keep your hair, clothing
and gloves away from moving parts.
Loose clothes, jewelry or long hair can be
caught in moving parts.
If devices are provided for the connec-
tion of dust extraction and collection
facilities, ensure these are connected
and properly used. Use of these devices
can reduce dust-related hazards.
WARNING
!
GENERAL SAFETY RULES
DM 2610925781 5-05.qxd 5/12/05 10:31 PM Page 2
3
Keep handles dry, clean and free from oil
and grease. Slippery hands cannot safely
control the power tool.
Power tool use and care
Do not force the power tool. Use the cor-
rect power tool for your application. The
correct power tool will do the job better and
safer at the rate for which it was designed.
Do not use the power tool if the switch
does not turn it on and off. Any power tool
that cannot be controlled with the switch is
dangerous and must be repaired.
Disconnect the plug from the power
source and/or the battery pack from the
power tool before making any adjust-
ments, changing accessories, or storing
power tools. Such preventive safety meas-
ures reduce the risk of starting the power
tool accidentally.
Store idle power tools out of the reach of
children and do not allow persons unfa-
miliar with the power tool or these
instructions to operate the power tool.
Power tools are dangerous in the hands of
untrained users.
Maintain power tools. Check for mis-
alignment or binding of moving parts,
breakage of parts and any other condi-
tion that may affect the power tools oper-
ation. If damaged, have the power tool
repaired before use. Many accidents are
caused by poorly maintained power tools.
Keep cutting tools sharp and clean.
Properly maintained cutting tools with sharp
cutting edges are less likely to bind and are
easier to control.
Use the power tool, accessories and tool
bits etc., in accordance with these
instructions and in the manner intended
for the particular type of power tool, tak-
ing into account the working conditions
and the work to be performed. Use of the
power tool for operations different from
those intended could result in a hazardous
situation.
Use clamps or other practical way to
secure and support the workpiece to a
stable platform. Holding the work by hand
or against your body is unstable and may
lead to loss of control.
Service
Have your power tool serviced by a quali-
fied repair person using only identical
replacement parts. This will ensure that the
safety of the power tool is maintained.
Develop a periodic maintenance sched-
ule for your tool. When cleaning a tool be
careful not to disassemble any portion of
the tool since internal wires may be mis-
placed or pinched or safety guard return
springs may be improperly mounted.
Certain cleaning agents such as gasoline,
carbon tetrachloride, ammonia, etc. may
damage plastic parts.
SAFETY RULES FOR ROTARY TOOL
Hold tool by insulated gripping surfaces
when performing an operation where the
cutting tool may contact hidden wiring or
its own cord. Contact with a "live" wire will
make exposed metal parts of the tool "live"
and shock the operator.
Use clamps or other practical way to
secure and support the workpiece to a
stable platform. Holding the work by hand
or against your body is unstable and may
lead to loss of control.
Accessories must be rated for at least the
speed recommended on the tool warning
label. Wheels and other accessories run-
ning over rated speed can fly apart and
cause injury.
If cutting into existing walls or other blind
areas where electrical wiring may exist is
unavoidable, disconnect all fuses or circuit
breakers feeding this worksite.
Do not operate the flexible shaft with a
sharp bend. Over bending the shaft can
generate excessive heat on the jacket or
hand piece. The recommended minimum is
6" radius.
Always disconnect the power cord from
the power source before making any
adjustments or attaching any acces-
SAVE THESE INSTRUCTIONS
DM 2610925781 5-05.qxd 5/12/05 10:31 PM Page 3

Termékspecifikációk

Márka: Dremel
Kategória: Csavaros gép
Modell: 300 Series

Szüksége van segítségre?

Ha segítségre van szüksége Dremel 300 Series, tegyen fel kérdést alább, és más felhasználók válaszolnak Önnek


Útmutatók Csavaros gép Dremel

Dremel

Dremel 256T6 Útmutató

22 Augusztus 2024
Dremel

Dremel 400 XPR Útmutató

12 Augusztus 2024
Dremel

Dremel 300 Series Útmutató

11 Augusztus 2024
Dremel

Dremel 764 Útmutató

26 Július 2024
Dremel

Dremel 750 Útmutató

26 Július 2024
Dremel

Dremel 398 Útmutató

26 Július 2024
Dremel

Dremel 276T6 Útmutató

26 Július 2024
Dremel

Dremel 761 Útmutató

26 Július 2024
Dremel

Dremel 760 Útmutató

26 Július 2024

Útmutatók Csavaros gép

Legújabb útmutatók Csavaros gép

Metabo

Metabo SE 2800 Útmutató

13 Január 2025
RYOBI

RYOBI One+ R18IW3 Útmutató

12 Január 2025
Hazet

Hazet 9012EL-SPC Útmutató

12 Január 2025
MSW

MSW -ACW700 Útmutató

11 Január 2025
RYOBI

RYOBI PCL250 Útmutató

5 Január 2025
RYOBI

RYOBI PCL212 Útmutató

5 Január 2025
Hazet

Hazet 9022 P-2 Útmutató

31 December 2025
Milwaukee

Milwaukee M18 BDD Útmutató

30 December 2025
Milwaukee

Milwaukee M12 BDD Útmutató

30 December 2025
Netter Vibration

Netter Vibration PKL 740 Útmutató

29 December 2024