Használati útmutató Crestron MPC-M20-B-T

Crestron Vezeték nélküli műsorvezető MPC-M20-B-T

Olvassa el alább 📖 a magyar nyelvű használati útmutatót Crestron MPC-M20-B-T (2 oldal) a Vezeték nélküli műsorvezető kategóriában. Ezt az útmutatót 6 ember találta hasznosnak és 2 felhasználó értékelte átlagosan 4.5 csillagra

Letöltés PDF

Oldal 1/2

DO GUIDE

DO Install the Device

The MPC-M10, MPC-M20, and MPC-M25 media presentation controllers

are designed to install into a standard 3-gang electrical box. After the

facility control network has been installed and veried, use the following

procedure to install the device.

NOTE: The MPC-M10, MPC-M20, and MPC-M25 are functionally similar,

and they share the same installation and programming process. For

simplicity within this guide, the term "MPC device" is used except where

noted.

Attach the Mounting Plate into an Electrical Box

1. Turn the system power off.

2. Use the four included 6-32 x 3/4" screws to attach the mounting plate

to the electrical box.

3. Attach the mounting plate ground wire to an earth ground.

NOTE: Ensure the unit is properly grounded.

Connect the Device

Route all appropriate cables through the electrical box, and then attach

them to the rear of the MPC device.

NOTE: All cable connections must be made prior to attaching the MPC

device to the mounting plate.

When making connections to the MPC device, note the following:

• Use Crestron® power supplies for Crestron equipment.

• Apply power after all connections to the device have been made.

• The included power cable cannot be extended.

NOTE: COM 2, IR 2, and RELAYS 3, 4, 5, and 6 are found only on the

MPC-M25.

NOTE: When connecting the included power supply to the NET connector

on the unit, make sure the lead with the white stripes connects to the

terminal marked “24.” The other lead connects to the terminal marked “G.”

Depending on the application, the MPC device INPUTS can be wired multiple ways. Refer to the following diagrams when wiring INPUTS.

WARNING: Incorrect wiring may damage the MPC device.

NOTE: The settings for the pull-up resistor are specied in the SIMPL Windows program. For more information, refer to the SIMPL Windows help le.

MPC-M10/MPC-M20/MPC-M25

MPC Media Presentation Controller

DO Check the Box

QUANTITY PRODUCT COLOR PART NUMBER

2 Connector, Butt Splice Red 2021836

1 Plate, Mounting 4506280

1 Power Cord, 6' 7" (2 m) 2001134

1 Power Pack, 24 Vdc 0.75 A, 100-240 Vac 2045852

2 Screw, 4-40 x 1/4", Pan Head, Phillips 2007156

4 Screw, 6-32 x 3/4", Truss Head, Combo 2009211

1 Tool, 1/16" Allen Wrench, L-shape, 3" Blade 2022867

For MPC-M10-W, MPC-M20-W, MPC-M25-W only

1 Labels, Sources, 100 Piece Set White 4509400

1 Labels, Actions, 100 Piece Set White 4509402

4 Screw, 4-40 x 1/2", Button Head, Hex 2021396

For MPC-M10-B-T, MPC-M20-B-T, MPC-M25-B-T only

1 Labels, Sources, 100 Piece Set Black 4509401

1 Labels, Actions, 100 Piece Set Black 4509403

4 Screw, 4-40 x 1/2", Button Head, Hex Black 2021395

For MPC-M10-W and MPC-M10-B-T only

1 Front Panel and Label, 10 Button White 4506184

1 Front Panel and Label, 10 Button Black 4506185

For MPC-M20-W and MPC-M20-B-T only

1 Front Panel and Label, 20 Button White 4506180

1 Front Panel and Label, 20 Button Black 4506181

For MPC-25-W and MPC-25-B-T only

1 Front Panel and Label, 20 Button White 4506178

1 Front Panel and Label, 20 Button Black 4506179

Input Wiring Diagrams - Digital Input Function Input Wiring Diagrams - Analog Input Function

Ground

wire

Mounting

plate

Screws (4): 6-32 x 3/4"

NET:

To any Cresnet®

network device

LAN:

10/100Base-T Ethernet to

LAN or web

COM:

To any RS-232

device

RELAYS:

To controllable

devices

IR:

To IRP2 or

serial devices

INPUTS:

From digital or

analog devices

Detecting a contact voltage

from a switch or relay

Analog input pull-up

resistor: disabled

Analog input pull-up

resistor: enabled

24 Vdc

max

1 2 3 4 G 1 2 3 4 G

Detecting a contact closure

from a switch or relay

Reading resistance

of a potentiometer

Reading voltage from

an analog source

Analog input pull-up

resistor: disabled

Analog input pull-up

resistor: enabled

10 Vdc

1 2 3 4 G 1 2 3 4 G

DO GUIDE

Attach the MPC Device to the Mounting Plate

Use the two included 4-40 x 1/4" screws to attach the MPC device to the mounting plate.

CAUTION: Excess wire that is pinched between the MPC device and the mounting plate could short

out. Make sure that all excess wire is completely contained inside the electrical box and not between

the box and the device.

Attach and Label the Buttons

1. Attach the three label holders by placing them over their respective slots and sliding them

downward into position.

2. Attach the included labels to the MPC by afxing them to their appropriate positions on the label

holders. Optional custom-engraved labels for the MPC device can be ordered separately by

downloading the Crestron Engraver software from .www.crestron.com/software

Attach the Face Plate to the MPC Device

Use the four included 4-40 x 1/2" screws and the included 1/16" Allen wrench to attach the face plate

to the MPC device.

NOTE: If programming the device using the COMPUTER (USB) port, detach the face plate by

removing the four 4-40 x 1/2" screws to access the port.

DO Program the Device

Use Crestron Toolbox™ software and one of the following communciation methods to program the

MPC device. Refer to the embedded Crestron Toolbox software help le for more information.

• Perform any necessary programming through the device's COMPUTER (USB) port prior to USB:

attaching the front panel to the MPC device.

• Perform any necessary programming over an Ethernet connection through the device's TCP/IP:

LAN port.

DOC. 7814A (2044892) 10.16

Specications subject to change without notice.

As of the date of manufacture, the product has been tested and found to comply with specications for CE marking.

These products are Listed to applicable UL Standards and requirements by Underwriters Laboratories Inc.

Ces produits sont énumérés aux normes applicables et les exigences UL par Underwriters Laboratories Inc.

Federal Communications Commission (FCC) Compliance Statement

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and (2) this device must accept any inter ference received, including interference that may cause undesired operation.

CAUTION: Changes or modications not expressly approved by the manufacturer responsible for compliance could void the user’s authority to operate the equipment.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection

against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may

cause harmful inter ference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.

If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference

by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

Industry Canada (IC) Compliance Statement

CAN ICES-3(B)/NMB-3(B)

Crest ron product development soft ware is licensed to Crest ron dealers and Crestron Service Providers (CSPs) under a limited non-exclusive, non-transferable Soft ware Development Tools License Agreement. Crestron product operating system soft ware is licensed to Crest ron dealers, CSPs, and

end-users under a separate End-User License Agreement. Bot h of these Agreements can be found on t he Crestron websit e at .www.crestron.com/legal /sof t ware_ license_agr eement

The specic patents that cover Crestron product s are list ed at . The product warranty can be found at www.pat ent s.crestron.com www.crest ron.com/warrant y.

Certain Crest ron products cont ain open source soft ware. For specic information, please visit . www.crestron.com/opensource

Crest ron, the Crest ron logo, Cresnet, Crestron Toolbox, and t he MPC logo are either trademarks or registered trademarks of Crestron Electronics, Inc., in the United St ates and/or other countries. UL and t he UL logo are either t rademarks or regist ered trademarks of Underwriters Laboratories,

Inc. in the United St ates and/or other count ries. Other trademarks, registered trademarks, and trade names may be used in this document to refer to either the entities claiming the marks and names or their product s. Crestron disclaims any propriet ary int erest in t he marks and names of ot hers.