Használati útmutató Code Corporation CodeXML M2

Code Corporation hálózati kártya/adapter CodeXML M2

Olvassa el alább 📖 a magyar nyelvű használati útmutatót Code Corporation CodeXML M2 (2 oldal) a hálózati kártya/adapter kategóriában. Ezt az útmutatót 8 ember találta hasznosnak és 2 felhasználó értékelte átlagosan 4.5 csillagra

Letöltés PDF
Oldal 1/2
2 C003345_01_CodeXML_Modem_Quickstart C003345_01_CodeXML_Modem_Quickstart 3
Figure 3
Cable Installation
Attach the end of the USB cable to the CodeXML Bluetooth® Modem
(Figure 2). Plug the USB connector into the USB port on the computer
(Figure 3). Once connected the modem’s blue LED light will turn on.
Establish Mode
Scan the USB Mode code (M708_01-right). Scan
the QuickConnect Code again. You are ready to
begin reading bar codes and transmitting decoded
data to the computer.
USB Mode
Keyboard Input (USB & PS2)
The modem is defaulted to English language keyboards. If you need to communicate in a different
language requiring a change in keyboard settings, please scan the appropriate code below, after
connecting to the modem:
CodeXML Bluetooth® Modem Installation as a USB Keyboard
Figure 2
USB Cable installed to
CodeXML Bluetooth Modem
Non-printable ASCII
Keyboard (Crtl + character)
Japanese Non-printable ASCII Keyboard
(No Leading 0)
Change Baud Rate Settings:
Scan the appropriate code below, after connecting to the modem These codes only affect Baud Note:
Rate for the modem and do not affect any settings on Code Readers.
Default Modem
settings:
Baud Rate: 9600
Stop Bits: 8
Parity: None
Stop Bits: 1
Hardware: None
Connecting with QuickConnect Code
(for all cable types):
Scan the QuickConnect Code on the label of the CodeXML Bluetooth®
Modem using the Code Reader with which you wish to establish a paired
connection to a computer. The reader and computer should easily
connect within 10 seconds. The reader will beep once as confi rmation.
If the reader does not connect, the reader will beep four times in rapid
succession.
English (Default) Universal French German
19200 38400 57600 115200
1200 2400 4800 9600 (Default)
CodeXML Modem Installatin with PS/2 Cable
Cable Installation
Attach the end of the PS/2 cable with the single connector to
the CodeXML Modem (Figure 2 -page 2). Detach the keyboard
from the computer and connect it to the same type connector on
the PS/2 cable (Figure 8). Connect the other cable end to the
computer (Figure 9). The modem is powered by the PS2 port and
does not require a power supply. Once connected the modem’s
blue LED light will turn on.
Connecting with QuickConnect Code
See instructions on page 2 for establishing a paired connection
between the modem and the computer.
PS/2 Cable installed to CodeXML
Modem & Keyboard
Figure 8
Figure 9
PS2 Mode
Establish Mode
Scan the PS2 Mode code (M660_01-right). You are
ready to begin reading bar codes and transmitting
decoded data
CodeXML Modem Installation with RS-232 (Serial)
Cable Installation
Attach the end of the RS-232 cable to the CodeXML Bluetooth® Modem (Figure 4). Connect the RS-232
adapter to the back of the computer (Figure 5). Connect the RS-232 cable to the power supply (Figure
6). Plug the power supply into a wall socket (Figure 7). Once connected the Modem’s blue LED light will
turn on.
Connecting with QuickConnect Code
See Page 2 for instructions to establish a paired connection between the
Modem and the reader.
Figure 5 Figure 6 Figure 7 Figure 4
RS-232 Cable (Left)
CodeXML Bluetooth Modem
(Center) Power Supply
(Right)
Establish Mode
Scan the RS-232 Mode code (M661_01- right).
Scan the QuickConnect Code again. You are
ready to begin reading bar codes and transmitting
decoded data to a computer.
RS232 Mode
Quickstart Guide
4 C003345_01_CodeXML_Modem_Quickstart
CodeXML M2 Bluetooth® Modem -
Multiple Interface Unit (MIU)
C003345_01_CodeXML_Modem_Quickstart 1
The CodeXML MIU Modem is an external PC accessory designed to be connected
to a computer for use with a Code Reader (CR2 or CR3). The Modem enables
a reader to wirelessly transmit captured data to the computer. The Modem can
accommodate USB, RS-232 (Serial) and PS/2 cables (Figure 1).
Figure 1
The CodeXML MIU Modem is ‘plug & play.’ You simply plug-in the Modem, scan
the QuickConnect code on the Modem Label and start transmitting data from Code
Readers without downloading any drivers or software. The Modem can receive
Bluetooth signals from up to 300 feet (100 meters) away.
For assistance, contact Code Technical Support at: 801 495 2200; or by
email: support@codecorp.com
CodeXML Modem MIU
Modem Firmware Version Output & Values (for reference only):
VVVVvvvvCKP BaudString:
VVVV 4 digit fi rmware version (MSP430 fi rmware version)
vvvv 4 digit fi rmware version (TUSB fi rmware version)
C 1 digit comm mode: 0=PS/2, 1=Serial, 2=Wand Emul., 3=USB
KBD
K Keyboard Map, same as reader host ICD setting 0x2d
P 1 digit packet protocol: 0=Raw, 1=SPX packet, 2=Code Reader
packet
4=Encrypted Packet Format, 5= Protocol Version (AES)
E Pre-emptible Mode
1=enabled, 0=off/disabled
BaudString spx: Baud:DataBitsParityStopbits
For All Readers:
Scan to View
Firmware Version
The radio contained in the CodeXML M2 Bluetooth® Modem has been tested for compliance
with FCC and CE regulations and was found to be compliant with all applicable FCC Rules and
Regulations.
FCC ID#: QQ6-BTR02
Model #: BTHDG-M2-RO-CX
The radio has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses, and can
radiate radio frequency energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However, there is no guarantee
that interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or more of the following
measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
- Consult the dealer or an experienced radio/TV technician for help.
Any changes made by the user not approved by Code Corporation can void the user’s authority
to operate the equipment.
To satisfy FCC RF exposure requirements for mobile transmitting devices, a separation of 20 cm
or more should be maintained between the antenna of this device and persons during device
operation. To ensure compliance, operations at closer than this distance are not recommended.
The antenna used for this transmitter must not be co-located in conjunction with any other
antenna or transmitter.
CodeXML M2 Bluetooth® Modem
Important Note:
US Patent: US 7,240,831, Patents Pending.

Termékspecifikációk

Márka: Code Corporation
Kategória: hálózati kártya/adapter
Modell: CodeXML M2

Szüksége van segítségre?

Ha segítségre van szüksége Code Corporation CodeXML M2, tegyen fel kérdést alább, és más felhasználók válaszolnak Önnek


Útmutatók hálózati kártya/adapter Code Corporation

Code Corporation

Code Corporation CodeXML M3 Útmutató

22 Augusztus 2024
Code Corporation

Code Corporation CodeXML M2 Útmutató

22 Augusztus 2024

Útmutatók hálózati kártya/adapter

Legújabb útmutatók hálózati kártya/adapter

Mikrotik

Mikrotik RB493 Útmutató

8 Április 2025
EtherWAN

EtherWAN EX41941F Útmutató

3 Április 2025
Vigitron

Vigitron MaxiiView Vi00023 Útmutató

3 Április 2025
AVPro Edge

AVPro Edge AC-MXNET-10G-TCVR Útmutató

2 Április 2025
EtherWAN

EtherWAN TG103H-0802 Útmutató

2 Április 2025
AVPro Edge

AVPro Edge MXNet AC-MXNET-10G-TCVR Útmutató

1 Április 2025
ScreenBeam

ScreenBeam ECB6250 Útmutató

30 Március 2025
Ubiquiti Networks

Ubiquiti Networks USW-Aggregation Útmutató

29 Március 2025
Vigitron

Vigitron Vi22601 Útmutató

15 Március 2025
Vigitron

Vigitron Vi22201 Útmutató

15 Március 2025