Használati útmutató Chief SLM229

Olvassa el alább 📖 a magyar nyelvű használati útmutatót Chief SLM229 (1 oldal) a Projektor tartozék kategóriában. Ezt az útmutatót 6 ember találta hasznosnak és 2 felhasználó értékelte átlagosan 4.5 csillagra

Oldal 1/1
I N S T A L L A T I O N I N S T R U C T I O N S
Milestone AV Technologies, and its affiliated corporations and subsidiaries (collectively, "Milestone"), intend to make this manual accurate and complete. However, Milestone makes
no claim that the information contained herein covers all details, conditions or variations, nor does it provide for every possible contingency in connection with the installation or use
of this product. The information contained in this document is subject to change without notice or obligation of any kind. Milestone makes no representation of warranty, expressed or
implied, regarding the information contained herein. Milestone assumes no responsibility for accuracy, completeness or sufficiency of the information contained in this document.
© 2008 Chief Manufacturing, a division of Milestone AV Technologies
8401 Eagle Creek Parkway, Savage, MN 55378
• P: 800.582.6480 / 952.894.6280 F:877.894.6918 / 952.894.6918
8802-000290
9/10/08
SLB-229 and SLM-229 Interface Brackets
SLB and SLM series Interface brackets are designed for use with Chief RPA, RPM, and Smart-Lift series projector mounts. See the specific
installation instructions provided with the mount for additional installation information.
Unpack carton and verify kit contents. If any listed parts are missing, immediately contact a Chief Customer Service representative by calling
1-800-582-6480.
WARNING: IMPROPER INSTALLATION CAN LEAD TO EQUIPMENT FALLING CAUSING SERIOUS PERSONAL INJURY AND
DAMAGE TO EQUIPMENT! DO NOT substitute hardware. Use only hardware supplied by manufacturer!
Installation:
WARNING: OVERTIGHTENING OF SCREWS CAN DAMAGE PARTS AND LEAD TO SERIOUS PERSONAL INJURY AND DAMAGE
TO EQUPIMENT! DO NOT over tighten screws when installing interface brackets.
NOTE: Step 1 is only required when installing an SLB Interface bracket. If an SLM bracket is being installed proceed to step 2.
1. Screw four thumb screws onto four 10-24 x 5/8" Philips pan head screws. DO NOT fully tighten thumb screws at this time.
2. Turn projector upside down on a flat surface.
3. Place the three nylon spacers on the bottom of the projector, lining them up with the three threaded inserts in the bottom of the projector.
4. Place the interface bracket onto the spacers, lining up the three holes in the bracket with the three spacers and threaded inserts on the
bottom of the projector.
5. Using the three M4 x 20mm flat head mounting screws, start them into the mounting holes by hand and secure all three fasteners at this
time.
NOTE: Security screws can be substituted when mounting Interface bracket to projector by using the parts and installation instructions in the
All-Points Security Kit.
(1) Interface Bracket (3) Washer, Flat, M4
(4) 10-24 Thumb Nuts ** (3) Screw, Phillips Flat Head, M4 x 20mm
(1) All-Points Security Kit (3) Spacer, Nylon, .500 x .194 x .500
(1) Hex Key, 5/32"
**Only used when installing SLB Interface brackets
SLB-229
SLM-229
Towards front
of projector
Towards front
of projector

Termékspecifikációk

Márka: Chief
Kategória: Projektor tartozék
Modell: SLM229

Szüksége van segítségre?

Ha segítségre van szüksége Chief SLM229, tegyen fel kérdést alább, és más felhasználók válaszolnak Önnek




Útmutatók Projektor tartozék Chief

Chief

Chief RPMC198 Útmutató

1 Január 2025
Chief

Chief RPMA360 Útmutató

1 Január 2025
Chief

Chief RSMA342 Útmutató

1 Január 2025
Chief

Chief RSMA360 Útmutató

1 Január 2025
Chief

Chief RPMC266 Útmutató

1 Január 2025
Chief

Chief RSMC360 Útmutató

1 Január 2025
Chief

Chief RPMA303 Útmutató

1 Január 2025
Chief

Chief RPMC246 Útmutató

1 Január 2025
Chief

Chief RSA000S Útmutató

1 Január 2025
Chief

Chief RSA360 Útmutató

1 Január 2025

Útmutatók Projektor tartozék

Legújabb útmutatók Projektor tartozék