Használati útmutató Biltema 84-1478

Biltema Rádióvezérlésű játékok 84-1478

Olvassa el alább 📖 a magyar nyelvű használati útmutatót Biltema 84-1478 (2 oldal) a Rádióvezérlésű játékok kategóriában. Ezt az útmutatót 6 ember találta hasznosnak és 2 felhasználó értékelte átlagosan 4.5 csillagra

Letöltés PDF

Oldal 1/2

Battery Installation

NO.: 84470

For Transmitter (Fig. 1 and Fig. 2)

1. Unscrew the screw on the battery cover

2. Open the battery cover

3. Install 2 new 1.5V “AAA” batteries with correct polarities (+/-)

as shown inside the battery compartment

4. Close the battery cover

5. Tighten the screw on the battery cover

-RC Vehicle (Vehicle) x 1

-RC Transmitter (Transmitter) x 1

-USB Charging Cable x1

-Instruction Manual x 1

Contents

RC Vehicle x 1 USB Charging CableRC Transmitter x 1

Fig. 1

Transmitter

Steering

Wheel

2.4 GHz

Signal Match

Button

Accelerator

Trigger

Transmitter - Battery Installation

Fig. 2

ages

3.7V Lithium

150mAh

For Vehicle

(Included)

3.7V

CAUTION

• Be Sure To Charge Battery Pack Before Using.

• If Battery Pack Is Hot After Use, Allow To Cool

Before Recharging.

• Do Not Dispose Of Battery Pack In Fire.

• Do Not Recharge Battery Pack That Shows

Leakage Or Corrosion, Or Attempt To Open Battery

Pack.

Charging the Rechargeable Battery Pack for the Vehicle (Fig. 3)

Rechargeable Battery Must Be

Recycled Or Disposed Of Properly.

1. The 3.7V rechargeable battery pack must be charged before use by utilizing the USB

Charging Cable which included.

2. Do not overcharge the battery pack. Do not charge for more than 4 hours.

3. Do not charge the battery pack if it shows leakage, corrosion, or has loose or exposed

wires or other damage.

4. Do not cover the battery pack with any sort of materials while charging.

5. Do not touch the battery pack when it is hot. Wait until the battery pack cools before

installing it in the Vehicle and before recharging.

6. Do not dispose of the battery in re.

7. Do not dismantle the battery or charger, and do not cut the battery or charger cables.

8. The battery pack will be warm after charging, and hot after use in a vehicle.

9. The supply terminals are not to be short-circuited.

10. Rechargeable batteries are only to be charged by adults.

11. Battery replacement must be only made by adults.

12. The USB Charging Cable is not a toy.

13. Charge only type (150mAh Max.) rechargeable battery packs. Other types of

batteries may burst causing injury to persons and damage. This USB Charging Cable

is intended to be used for charging 3.7V rechargeable battery pack

with capacity 150mAh Max. It cannot be used for charging non-rechargeable

batteries. Regular examination of USB Charging Cable for any damage to their

cord, plug, enclosure and other parts, and that, in the event of such damage, it

must not be used with the charger or battery pack charge until such damage

has been repaired. Note that the AAA battery is non-rechargeable and is not to

be recharged. Only batteries of the same or equivalent type as recommended

are to be used. It will need replacement when transmission is poor.

14. Exhausted batteries are to be removed from the product.

15. Non-rechargeable batteries are not to be recharged.

16. Dierent types of batteries or new and used batteries are not to be mixed.

17. Batteries are to be inserted with the correct polarity.

18. The packaging have to be kept since they contain the important information and

instruction manual.

19. Chargers used with the toy are to be regularly examined for damage to the cord,

plug, enclosure and other parts, and that, in the event of such damage, the toy must

not be used with the charger until the damage has been repaired.

20. The Toy is only to be connected to Class II or class III equipment bearing either of

the following symbols: or回

1. Connect the 3.7V rechargeable battery pack to the USB Charging Cable.

2. Recommend use Computer connect USB Charging Cable to charge the battery.

If use adaptor connect USB Charging Cable to charge battery, the output limit cannot

exceed 3.7V.

3. The charging time for a full charge is about 1 hour. Full charge battery usage Max. 30 mins.

4. When charging is completed, unplug the USB Charging Cable.

5. Disconnect the rechargeable battery pack from the Charging Cable.

FULL

FUNCTION

1:12

SCALE

CHARGING CABLE

Fig. 3

Vehicle

Charging plug

84470

The packaging and instruction manual contain important information. Please keep them

for future reference.

Warning! Choking Hazard. Not suitable for children under the age of 3 years due to

small parts.

We reserve the right to improve/amend specifications and colors without notice.

3. Use the Accelerator Trigger to drive the Vehicle Forward, Stop and Backward

4. Play on smooth surface to have the optimum performance

5. Remember to switch OFF the power of the Vehicle after

playing

6. The optimum control range is up to 15m outdoor

1. Switch ON the Vehicle

Turn Left Turn Right

2. Use the Steering Wheel to control the Vehicle turning left or right

FCC label compliance statement:

This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and

2. This device must accept any interference received, including interference that may cause undesired operation. Note: This equipment has been tested and found to comply with

the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential

installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interfer-

ence to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or

television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

- Reorient or relocate the receiving antenna

- Increase the separation between the equipment and receiver

- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected

- Consult the dealer or an experienced radio/TV technician for help

Warning: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

RSS-210 Compliance Statement:

This device complies with Industry Canada Licence-exempt RSS-210. Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this

device must accept any interference, including interference that may cause undesired operation of the device.

Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser) gain approved for the transmitter by Industry

Canada,. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent

isotropically radiated power (e.i.r.p.) is not more than that necessary for successful communication.

Declaration of Conformity

The product is in conformity with the requirement of EU Directive 2014/53/EU.

Environmental notes:

The whole product also does not belong to household waste at the end of the product life.

You can return it at collection points for the recycling of electronic and electronical instruments

The symbol on the item, instruction manual, hangtag or packing is showing this clearly.

Materials should be recycled according to their respective markings.

Recycling of old devices or other re-use of materials contained therein represents an important

contribution to environmental protection.

Please ask at your local community for the correct collection point.

Disposal of batteries

Batteries should not be disposed of in the household waste. As the consumer you are legally obliged to

return batteries containing harmful substances and all other used batteries. You can hand in your old

batteries at public collection points in your area or wherever batteries are sold.

You will find these chemical abbreviations along with a crossed-out refuse bin on batteries containing

harmful substances:

Pb=Battery contains lead

Cd=Battery contains cadmium

Hg=Battery contains mercury

Performance Tips

1. Do not drive on grass, dirt, sand, dusts, carpet or go through water.

2. Do not drive in windy or rainy weather.

3. Avoid direct impact the Vehicle with obstacles.

4. Switch OFF the power when not in use to prevent damage of Vehicle and Transmitter

due to leakage of electrolyte from batteries.

5. Remove all batteries from the Vehicle and Transmitter when not in use for long period.

6. Keep fingers, hair and loose clothing away from wheels.

7. The operating range can be affected by a variety of factors

a) Low Voltage of batteries in Transmitter or Vehicle

b) Interference from other items that emit radio frequency signals.

8. Outdoor usage is recommended in order to get optimum control range.

9. Recommend to play the vehicle on a clean and smooth surface.

10. Clean the battery compartment to make sure it is free from dust to prevent poor

contact of batteries

Cautions

1. Do not attempt to disassemble the Vehicle or Transmitter

2. Make sure the batteries are installed with correct polarities (+/-) as shown inside the

battery compartment

3. Remove the package and take out all accessories before giving the Vehicle and

Transmitter to child to play

Conforms to the safety requirements of ASTM F963

1. Turn on the Vehicle.

2. Hold the Signal Match Button for around 4 second then the Transmitter signal light will flash for 6-7 second.

3. After the wheels of the Vehicle turn left and right and the LED light of the Transmitter stops flashing, the binding process completed for playing.

4. If it cannot complete within 8 seconds, please turn off the Vehicle and re-start the binding process.

5. When the binding process is done, whenever switching the Vehicle on and off, it searches for the code that it memorized, and will only lock on to the

Transmitter signal containing that code.