Használati útmutató Bauknecht OBIC Ecospace 8650

Bauknecht mosogatógép OBIC Ecospace 8650

Olvassa el alább 📖 a magyar nyelvű használati útmutatót Bauknecht OBIC Ecospace 8650 (12 oldal) a mosogatógép kategóriában. Ezt az útmutatót 4 ember találta hasznosnak és 2 felhasználó értékelte átlagosan 4.5 csillagra

Letöltés PDF
Oldal 1/12
ENQuick Guide
1
THANK YOU FOR BUYING A BAUKNECHT PRODUCT.
In order to receive a more complete assistance, please
register your appliance on: www.bauknecht.eu/register
CONTROL PANEL
FIRST TIME USE
1. ON-OFF/Reset button with indicator light
2. Program selection button
3. Salt rell indicator light
4. Rinse Aid rell indicator light
5. Program number and delay time indicator
6. Tablet indicator light
7. Display
8. Multizone indicator lights
9. Multizone button
10. Delay button
11. START/Pause button with indicator
light / Tablet (Tab)
PROGRAMS TABLE
Before using the appliance carefully read the Safety Instruction.
PLEASE SCAN THE QR CODE ON YOUR
APPLIANCE IN ORDER TO HAVE MORE
DETAILED INFORMATION
3
1
2
854 6 97 10 11
FILLING THE SALT RESERVOIR
The use of salt prevents the formation of LIMESCALE on the dishes and on
the machine’s functional components.
• It is mandatory that the salt reservoir never be empty.
• It is important to set the water hardness.
The salt reservoir is located in the lower part of the dishwasher and must be
lled when the SALT REFILL indicator light in the control panel is lit.
1. Remove the lower rack and unscrew the reservoir cap
(anticlockwise).
2. Only the rst time you do this: ll the salt reservoir
with water.
3. Position the funnel and ll the salt reservoir (see gure)
right up to its edge (approximately 1 kg); it is not unu-
sual for a little water to leak out.
4. Remove the funnel and wipe any salt residue away from the opening.
Make sure the cap is screwed on tightly, so that no detergent can get into
the container during the wash program (this could damage the water
softener beyond repair).
Whenever you need to add salt, it is mandatory to complete the proce-
dure before the beginning of the washing cycle to avoid corrosion.
FILLING THE RINSE AID DISPENSER
Rinse aid makes dish DRYING easier. The rinse
aid dispenser should be lled when the A RINSE
AID REFILL indicator light in the control pan-
el is lit. NEVER pour the rinse aid directly into
the appliance tub.
A
C
D
FILLING THE DETERGENT DISPENSER
To open the detergent dispenser use the opening device C. Introduce the
detergent into the dry dispenser only. Place the amount of detergent for D
pre-washing directly inside the tub.
If all-in-one detergents are used, we recommend using the TABLET button,
because it adjusts the program so that the best washing and drying results
are always achieved.
Usage of detergent not designed for dishwashers may cause
malfunction or damage to the appliance.
WATER SOFTENING SYSTEM
Water softener automatically reduces water hardness, consequently pre-
venting scale buildup on heater, contributing also to better cleaning e-
ciency. This system regenerates itself with salt, therefore it is required
to rell salt container when empty.
Frequency of regeneration depends on water hardness level setting - regen-
eration takes place once per 6 Eco cycles with water hardness level set to 3.
Regeneration process starts in nal rinse and nishes in drying phase, be-
fore cycle ends.
• Single regeneration consumes: ~3.5L of water;
• Takes up to 5 additional minutes for the cycle;
• Consumes below 0.005kWh of energy.
ECO program data is measured under laboratory conditions according to European Standard EN 60436:2020.
Note for Test Laboratories: For information on comparative EN testing conditions, please send an email to the following address: dw_test_support@whirlpool.com
Pre-treatment of the dishes is not needed before any of the programs.
*) Not all options can be used simultaneously.
**) Values given for programs other than the program Eco are indicative only. The actual time may vary depending on many factors such as temperature and
pressure of the incoming water, room temperature, amount of detergent, quantity and type of load, load balancing, additional selected options and sensor
calibration. The sensor calibration can increase program duration up to 20 min.
Pro-
gram Programs description
Drying
phase
ActiveDry
Available
options *)
Duration
of wash
program
(h:min)**)
Water
consumption
(litres/cycle)
Energy
consumption
(kWh/cycle)
1.
Eco 50°- Program is suitable to clean normally soiled tableware,
that for this use, it is the most ecient programme in terms of its
combined energy and water consumption, and that it is used to
assess compliance with the EU Ecodesign legislation. 3:20 9.5 0.64
2. Sensor 50°-60° - For normally soiled dishes with dried food re-
sidues. Senses the level of soiling on the dishes and adjusts the
program accordingly. 1:25 - 3:00 7.0 - 14.0 0.90 - 1.40
3. Intensive 65° - Program recommended for heavily soiled croc-
kery, especially suitable for pans and saucepans. 2:50 17.0 1.60
4. Fast Wash&Dry 50° - Normally soiled crockery. Everyday cycle,
that ensures optimal cleaning and drying performance in shor-
ter time. 1:25 11.5 1.10
5. Glass 45° - Program for delicate items, which are more sensitive
to high temperatures, for example glasses and cups. 1:40 12.0 1.20
6. Rapid 30’ - 50° Program to be used for half load of lightly-soiled
dishes with no dried food residues. Without drying. - 0:30 9.0 0.50
7. Silent - 50° Suitable for night-time operation of the appliance.
With the lowest noise. 3:30 16.0 1.15
8. Prewash - Use to refresh crockery planned to be washed later.
No detergent to be used with this program. - - 0:12 4.5 0.01
2
Quick GuideEN
DELAY - The start time of the program may be delayed for a period of
time between and hours.1 12
The DELAY function cannot be set once a wash cycle has been started.
TABLET (Tab)- If you use powder or liquid detergent, this option
should be o.
OPTIONS AND FUNCTIONS
OPTIONS can be selected directly by pressing the corresponding button (see CONTROL PANEL). If an option is not compatible with the selected
program (see PROGRAMS TABLE), the corresponding LED ashes rapidly 3 times and beeps will sound. The option will not be enabled.
MULTIZONE - If there are not many dishes to be washed, a half loading
may be used in order to save water, electricity and detergent. By de-
fault the appliance washes dishes in all racks. OPERATION INDICATOR -
A LED light projected on the oor indicates
that the dishwasher is working.
One of the following operating modes can be selected:
a) Disabled function.
b) When the cycle starts the light goes on for few seconds, stays o during
the cycle and ashes at the end of the cycle.
c) The light stays on during the cycle and ashes at the end of the cycle
(default mode).
Please scan on your product in order to have more detailed information. the QR code
ActiveDry
is a convection drying system which automatically opens the door
during/after drying phase to ensure exceptional drying performance every
day. Door opens at the temperature that is safe to your kitchen furniture.
LOADING THE RACKS CAPACITY: 14 standard place-settings
LOWER RACK
For pots, lids, plates, sa-
lad bowls, cutlery etc.
Large plates and lids
should ideally be pla-
ced at the sides to avo-
id interferences with
the spray arm.
The lower rack has tip-
-up supports which
can be used in a verti-
cal position when ar-
ranging plates or in a
horizontal position (lo-
wer) to load pans and
salad bowls easily.
(loading example for the
lower rack)
CUTLERY RACK
(loading example for the cutlery rack)
The third rack was designed to
house the cutlery.
UPPER RACK
(loading example for the upper rack)
Load delicate and light dishes: glasses,
cups, saucers, low salad bowls.
FOLDABLE
FLAPS WITH
ADJUSTABLE
POSITION
CUTLERY BASKET
It istted with top grids for improved cutlery arrange-
ment. It must only be positioned at the front of the
lower rack.
Knives and other utensils with sharp edges must be
placed in the cutlery basket with the points facing
downwards or they must be positioned horizontally
in the tip-up compartments on the upper rack.
More information in the Daily Reference Guide on website.
CLEANING AND MAINTENANCE
CLEANING THE FILTER ASSEMBLY CLEANING THE SPRAY ARMS
A
A
B
C
In case you nd foreign objects (such as broken glass, porcelain, bones, fruit seeds etc.)
please remove them carefully.
NEVER REMOVE the wash-cycle pump protection (black detail) (Fig 4).
To remove the upper spray arm,
turn the plastic locking ring in a
clockwise direction.
The lower spray arm may
be removed by pulling it
upwards.
ENQuick Guide
3
PROBLEMS POSSIBLE CAUSES SOLUTIONS
The dishwasher does not
ll the water.
Display shows: H,
6 and On/O LED is blin-
king rapidly
No water in the water supply or the tap
is closed. Make sure there is water in the water supply or the tap running.
The inlet hose is bent. Make sure the inlet hose is not bent (see INSTALLATION) reprogram the dishwa-
sher and reboot.
The sieve in the water inlet hose is clog-
ged; it is necessary to clean it
After having carried out the verication and cleaning, turn o and turn on the
dishwasher and restart a new program.
Dishwasher nishes the
cycle prematurely.
Display shows: 15
and On/
O LED is blinking
rapidly
Drain hose positioned too low or sipho-
ning into home sewage system.
Check if end of drain hose is placed at correct height (see INSTALLATION).Check
for siphoning into home sewage system, install air admittance valve if necessary.
Air in water supply. Check water supply for leaks or other issues letting air inside.
In case your dishwasher doesn’t work properly, check if the problem can be solved by going through the following list. For other errors or issues
please contact authorized After-sales Service which contact details can be found in the warranty booklet. Spare parts will be available for a period
of either up to 7 or up to 10 years, according to the specic Regulation requirements.
TROUBLESHOOTING
Please scan the on your product in order to have more detailed information. QR code
Policies, standard documentation, ordering of spare parts and additional product information can be found by:
• Using QR code on your product.
• Visiting our website docs.bauknecht.eu and parts-selfservice.whirlpool.com
• Alternatively, contact our After-sales Service (See phone number in the warranty booklet). When contacting our After-sales
Service, please state the codes provided on your product’s identication plate.
The model information can be retrieved using the QR-Code indicated on the energy label. The label also includes the model
identier that can be used to consult the https://eprel.ec.europa.eu database portal.
IEC 436
:

Termékspecifikációk

Márka: Bauknecht
Kategória: mosogatógép
Modell: OBIC Ecospace 8650

Szüksége van segítségre?

Ha segítségre van szüksége Bauknecht OBIC Ecospace 8650, tegyen fel kérdést alább, és más felhasználók válaszolnak Önnek


Útmutatók mosogatógép Bauknecht

Bauknecht

Bauknecht BCIF 5O539 PLEGT Útmutató

14 Január 2025
Bauknecht

Bauknecht GSI 4743/3 BR Útmutató

13 Január 2025
Bauknecht

Bauknecht B0I D541A S Útmutató

11 Január 2025
Bauknecht

Bauknecht OBBC Ecosilent 8650 Útmutató

3 Január 2025
Bauknecht

Bauknecht B2I HKD526 A Útmutató

24 December 2024
Bauknecht

Bauknecht B2I HKD524 AS Útmutató

19 December 2024
Bauknecht

Bauknecht OBIC Ecospace 8650 Útmutató

19 December 2024
Bauknecht

Bauknecht GSXP 50/1 Power Útmutató

9 December 2024
Bauknecht

Bauknecht GSIP 6527 IN Útmutató

9 December 2024
Bauknecht

Bauknecht GSXK 5011 A+ Útmutató

15 Október 2024

Útmutatók mosogatógép

Legújabb útmutatók mosogatógép

Neff

Neff S583C50X0G Útmutató

14 Január 2025
Etna

Etna ENFI 8517 Útmutató

14 Január 2025
Candy

Candy CDCF 6 Útmutató

14 Január 2025
Ariston Thermo

Ariston Thermo LSI 41 Útmutató

14 Január 2025
Grundig

Grundig GNVP4432PW Útmutató

14 Január 2025
Whirlpool

Whirlpool WH3ID10BS7SA0 Útmutató

14 Január 2025
Whirlpool

Whirlpool WH8IA15AM3TUS0 Útmutató

14 Január 2025
Whirlpool

Whirlpool WH8IC15B4M6LHC0 Útmutató

14 Január 2025
Whirlpool

Whirlpool W0I D734L S Útmutató

14 Január 2025
Hoover

Hoover HFS 2F492X/E Útmutató

14 Január 2025