Használati útmutató ATen VM8584

ATen hi-fi rendszer VM8584

Olvassa el alább 📖 a magyar nyelvű használati útmutatót ATen VM8584 (2 oldal) a hi-fi rendszer kategóriában. Ezt az útmutatót 7 ember találta hasznosnak és 2 felhasználó értékelte átlagosan 4.5 csillagra

Letöltés PDF

Oldal 1/2

VM7584 / VM8584

4-Port 10G Optical Input Board / Output Board Quick Start Guide

Hardware Review

Panel View

1. Link LEDs

2. SFP+ Ports

3. IR Ports

4. RS-232 Channel Ports

5. Status LED

Hardware Setup

I/O Board Installation

Follow the steps below to safely install the VM7584 / VM8584 board to a

supporting Modular Matrix Switch. For a list of the supported Modular Matrix

Switch, visit the VM7584/VM8584 product web pages.

Note: The VM3250 is used as an example in the instructions below.

1. Power off the Modular Matrix Switch.

Note: The VM7584/VM8584 boards are hot-swappable.

2. On the rear of the Modular Matrix Switch, unscrew the Phillips head screws

for one input slot (right) and one output slot (left), and then remove back

panel covers.

3. Slide the VM7584 into the input board slot, and the VM8584 into the output

slot. Make sure they secure in place.

4. Tighten the screws on the boards to secure the input and output

boards to the Modular Matrix Switch.

5. To install more I/O boards, repeat steps 2 to 4.

6. Proceed to the next section to install sources and displays.

VM7584 Front View VM8584 Front View

1 2

3 4 3 4

1 2 1 2

3 4 3 4

1 2 5

1 2

3 4 3 4

1 2 1 2

3 4 3 4

1 2 5

1 2

3 4 3 4

1 2 1 2

3 4 3 4

1 2

Output Slots Input Slots

K1 Package (300 m) Contents

1 VM7584 4-Port 10G Optical Input Board or

VM8584 4-Port 10G Optical Output Board

4 SFP+ modules

4 3-Pole Terminal Blocks

1 IR Receiver

1 IR Emitter

1 User Instructions

K2 Package (10 km) Contents

1 VM7584 4-Port 10G Optical Input Board or

VM8584 4-Port 10G Optical Output Board

4 SFP+ modules

4 3-Pole Terminal Blocks

1 IR Receiver Cable

1 IR Emitter Cable

1 User Instructions

VM7584 VM8584

Support and Documentation

Notice

All information, documentation,

ﬁrmware, software utilities, and

speciﬁcations contained in this

package are subject to change

without prior notiﬁcation by

the manufacturer.

To reduce the environmental

impact of our products, ATEN

documentation and software can

be found online at

http://www.aten.com/

download/

Technical Support

www.aten.com/support

® International Co., Ltd.

are the property of their respective owners.

This product is RoHS compliant.

Source and Display Device Installation

1. Connect one or more VE883T units to the SFP+ ports of the VM7584.

2. Connect one or more VE883R units to the SFP+ ports of the VM8584.

3. (Optional) To bypass RS-232 serial signals via the VM7584/8584, connect a serial controller to the RS-232

Serial port on either the VM7584 or VM8584.

4. (Optional) To bypass IR signals, connect the supplied IR receiver to the IR port on either the VM7584 or

VM8584, depending on which side you prefer to emit IR signals, and then the IR emitter to the IR port on

other board.

5. Ground the Modular Matrix Switch and all the devices in the installation.

6. Power on the Modular Matrix Switch and all the devices in the installation.

IR Emitter

IR Receiver

Serial Device

VE883R

VE883T

IR Emitter

IR Receiver

Serial Device

VE883R

VE883T

이 기기는 업무용(A급) 전자파적합기기로서 판매자 또는 사용자는 이 점을 주의하시기 바라며, 가정외의 지역에서 사

용하는 것을 목적으로 합니다.

Scan for

more information

EMC Information

FEDERAL COMMUNICATIONS COMMISSION INTERFERENCE STATEMENT:

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15

of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the

equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency

energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to

radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which

case the user will be required to correct the interference at his own expense.

FCC Caution: Any changes or modiﬁcations not expressly approved by the party responsible for compliance could void

the user's authority to operate this equipment.

Warning: Operation of this equipment in a residential environment could cause radio interference.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device

may not cause harmful interference, and (2) this device must accept any interference received, including interference

that may cause undesired operation.

Important. Before proceeding, download the by visiting the website, Installation and Operation Manual

www.aten.com and navigating to the product page. The manual includes important warnings, loading

speciﬁcations and grounding instructions.

Termékspecifikációk

Márka:	ATen
Kategória:	hi-fi rendszer
Modell:	VM8584

Szüksége van segítségre?

Ha segítségre van szüksége ATen VM8584, tegyen fel kérdést alább, és más felhasználók válaszolnak Önnek

Az Ön neve*

Az Ön e-mail címe*

Írja ide kérdését

Útmutatók hi-fi rendszer ATen

ATen VM8584 Útmutató

15 Augusztus 2024

Útmutatók hi-fi rendszer

Legújabb útmutatók hi-fi rendszer

NEC NP01SW1 Útmutató

9 Április 2025

Klipsch ProMedia Ultra 2.0 Útmutató

6 Április 2025

Vaxis Atom 500 Útmutató

2 Április 2025

INKEE Benbox Útmutató

1 Április 2025

JL Audio SlamPak SLPK-CAN-SPYDER1 Útmutató

31 Március 2025

Teradek Bolt 10K Útmutató

29 Március 2025

Teradek Bolt 500 Útmutató

29 Március 2025

Teradek Cubelet 655 Útmutató

29 Március 2025

Teradek Cube Series Útmutató

29 Március 2025

Teradek Cube 725 Útmutató

29 Március 2025