Használati útmutató APC NetBotz Camera Pod 165

APC Térfigyelő kamera NetBotz Camera Pod 165

Olvassa el alább 📖 a magyar nyelvű használati útmutatót APC NetBotz Camera Pod 165 (2 oldal) a Térfigyelő kamera kategóriában. Ezt az útmutatót 4 ember találta hasznosnak és 2 felhasználó értékelte átlagosan 4.5 csillagra

Letöltés PDF

Oldal 1/2

NetBotz Camera Pod 165

Installation and Quick Start

NBPD0165

Product Description

The APC by Schneider Electric® NetBotz Camera Pod 165 is a motion-

sensitive camera capable of sending image data through a connection to

a NetBotz Rack Monitor 750. The Camera Pod 165 can be triggered by

the appliance in response to a number of environmental alarms or

events, such as a temperature spike or the action of opening a door. The

Camera Pod 165 can also provide constant surveillance of an area or

entrance.

Receiving

Inspect the package and contents for shipping damage. Make sure all

parts were sent. Immediately report any shipping damage to the shipping

agent. Report missing contents, product damage, or other problems with

the product to APC by Schneider Electric or your Schneider Electric

reseller.

NOTICE

The equipment contains, and the software enables, visual recording

capabilities, the improper use of which may subject you to civil and criminal

penalties. Applicable laws regarding the use of such capabilities vary between

jurisdictions and may require, among other things, express written consent

from recorded subjects. You are solely responsible for insuring strict

compliance with such laws and for strict adherence to any/all rights of privacy

and personalty. Use of this software for illegal surveillance or monitoring shall

be deemed unauthorized use in violation of the end user software agreement

and result in the immediate termination of your license rights thereunder.

Customer support and warranty information is available at

www.apc.com.

990-5974A-001 9/2019

Physical Description

Item Description

RJ-45 port For network and Power Over Ethernet (PoE) connections

Network LEDs Link LED: turns green to indicate a good network connection.

Activity LED: flashes orange to indicate network activity

Power jack Reserved for future use

Alarm In/Out Reserved for future use

Mounting hole Used to mount the Camera Pod 165

Micro SD card slot Reserved for future use

Reset button Press for at least 20 seconds to reset to factory defaults

aem0555a















Inventory

Item Description Quantity

Camera Pod 165 1

Rubber bracket cover 1

T-bar mounting plate 1

Set screw* 1

Hex wrench* 1

Ball-joint adjuster arm 2

Extender arm 2

Mounting plate 1

*Not used

aem0556a

   

 

Installation

Choose the mounting option (rack, wall, or ceiling) that meets your needs.

Then connect the Camera Pod 165 to your NetBotz appliance or to the

network.

Rack mount

Use #8 sheet-metal screws (not provided) to secure the camera pod. Use

a #32 drill to make four 2.94 mm (0.116 in) pilot holes in the rack.

Ceiling mount

aem0283c

aem0285c

Wall mount

Use #8 screws (not provided) to secure the camera pod.

Connect the Camera Pod 165 to a NetBotz 5.x appliance

Use a Power over Ethernet (PoE) ready, CAT-5 Ethernet cable to

connect the Camera Pod 165 to the Private LAN port of your appliance.

Connect the Camera Pod 165 to your network

If you do not connect the Camera Pod 165 to an appliance, you can use

a PoE-ready CAT-5 Ethernet cable, PoE equipment, and a network

switch to connect the Camera Pod 165 to your network.

Configuration

See the on User Guide www.apc.com for instructions to configure the

camera pod in the Web User Interface (UI) of your NetBotz appliance.

The Camera Pod 165 is automatically set to have a dynamic IP address

assigned via DHCP. If the Camera Pod 165 is not connected directly to

an appliance, you can use Device Search to view the current IP address

of the Camera Pod 165 or to assign it a static IP address.

Use Device Search to discover the IP address

1. Connect your computer to the same subnet as the

Camera Pod 165.

2. Go to the CameraPod 165 product page on www.apc.com.

Download and open the executable file.DeviceSearch

3. In the Device Search window, select All NetCard from the Local

Broadcast Device Search drop-down list and click . Wait for the

search to finish. You can identify you Camera Pod 165 by its MAC

address, which you can find on the back of the unit.

Use Device Search to set a static IP address

1. Follow the instructions to discover the IP address of the

Camera Pod 165.

2. In the window, right-click the Camera Pod 165, Device Search

and select to open the window.Network Setup Network Setup

3. Select Static IP, and enter the static , default gateway IP address

(Gateway), Subnet Mask (Netmask), and Domain Name System

server ( ) for your Camera Pod 165. DNS

aem0284c

Change the password

NOTE: The Camera Pod 165 Web UI is only used to change the password and

upgrade the firmware.

When connecting an un-configured camera pod directly to an appliance, you

do not have to change the password—the appliance configures the camera

security automatically. Password changes are only required for remote

connections to an appliance.

1. Enter the camera pod IP address in the URL address bar of your Web

browser, then log on using the default user name and password ( apc

and ). apc

2. When prompted, enter a new password in the Admin password and

Confirm password Save fields, then click . The password is case

sensitive and must be at least 8 characters longs.

To change the password after first use, Log on to the camera pod Web UI, then

select System > Security > User. Enter the new password in the Admin

password Confirm password Save and fields, then click .

To recover a lost password, press the reset button for 20 seconds, wait 5-10

minutes for the camera pod to restart, then repeat this procedure.

Upgrade the firmware

NOTE: The Camera Pod 165 Web UI is only used to change the password and

upgrade the firmware.

1. Download the latest firmware version from the applicable product page

of www.apc.com.

2. Enter the camera pod IP address in the URL address bar of your Web

Browser. Log in, then select . System > Software Upgrade

3. Select , then browse to the appropriate firmware file.Browse...

4. Click , then wait for the upgrade to complete. If you lose Upgrade

connection to the Web UI, refresh the page.

5. Select System > Software Version to view the current firmware version

and verify that the upgrade was successful.

Adjust the focus

Remove the lens cover. Twist the lens to the left and right until the image

becomes clear.

Specifications

Electrical

Power Source Power over Ethernet

Power Consumption: Operation

(802.3af) system

3.7 W

Mechanical

Dimensions (H x W x L) 96.51 x 56 x 61.4 mm (3.78 x 2.2 x 2.42 in.)

Weight 120 g (0.26 lb)

Environmental

Operating temperature 0–45°C (32–113° F)

Humidity 10–90%, no condensation

Compliance

Safety CE (LVD)

EMC FCC / CE (EMC Directive)

Two-Year Factory Warranty

This warranty applies only to the products you purchase for your use in accordance with this manual.

Terms of warranty

APC by Schneider Electric warrants its products to be free from defects in materials and workmanship for

a period of two years from the date of purchase. APC by Schneider Electric will repair or replace

defective products covered by this warranty. This warranty does not apply to equipment that has been

damaged by accident, negligence or misapplication or has been altered or modified in any way. Repair or

replacement of a defective product or part thereof does not extend the original warranty period. Any parts

furnished under this warranty may be new or factory-remanufactured.

Non-transferable warranty

This warranty extends only to the original purchaser who must have properly registered the product. The

product may be registered at the APC by Schneider Electric Web site, www.apc.com.

Exclusions

APC by Schneider Electric shall not be liable under the warranty if its testing and examination disclose

that the alleged defect in the product does not exist or was caused by end user’s or any third person’s

misuse, negligence, improper installation or testing. Further, APC by Schneider Electric shall not be liable

under the warranty for unauthorized attempts to repair or modify wrong or inadequate electrical voltage

or connection, inappropriate on-site operation conditions, corrosive atmosphere, repair, installation,

exposure to the elements, Acts of God, fire, theft, or installation contrary to APC by Schneider Electric

recommendations or specifications or in any event if the APC by Schneider Electric serial number has

been altered, defaced, or removed, or any other cause beyond the range of the intended use.

THERE ARE NO WARRANTIES, EXPRESS OR IMPLIED, BY OPERATION OF LAW OR

OTHERWISE, OF PRODUCTS SOLD, SERVICED OR FURNISHED UNDER THIS AGREEMENT OR

IN CONNECTION HEREWITH. APC BY SCHNEIDER ELECTRIC DISCLAIMS ALL IMPLIED

WARRANTIES OF MERCHANTABILITY, SATISFACTION AND FITNESS FOR A PARTICULAR

PURPOSE. APC BY SCHNEIDER ELECTRIC EXPRESS WARRANTIES WILL NOT BE ENLARGED,

DIMINISHED, OR AFFECTED BY AND NO OBLIGATION OR LIABILITY WILL ARISE OUT OF, APC

BY SCHNEIDER ELECTRIC RENDERING OF TECHNICAL OR OTHER ADVICE OR SERVICE IN

CONNECTION WITH THE PRODUCTS. THE FOREGOING WARRANTIES AND REMEDIES ARE

EXCLUSIVE AND IN LIEU OF ALL OTHER WARRANTIES AND REMEDIES. THE WARRANTIES SET

FORTH ABOVE CONSTITUTE APC BY SCHNEIDER ELECTRIC’S SOLE LIABILITY AND

PURCHASER’S EXCLUSIVE REMEDY FOR ANY BREACH OF SUCH WARRANTIES. APC BY

SCHNEIDER ELECTRIC WARRANTIES EXTEND ONLY TO PURCHASER AND ARE NOT

EXTENDED TO ANY THIRD PARTIES.

IN NO EVENT SHALL APC by Schneider Electric, ITS OFFICERS, DIRECTORS, AFFILIATES OR

EMPLOYEES BE LIABLE FOR ANY FORM OF INDIRECT, SPECIAL, CONSEQUENTIAL OR

PUNITIVE DAMAGES, ARISING OUT OF THE USE, SERVICE OR INSTALLATION, OF THE

PRODUCTS, WHETHER SUCH DAMAGES ARISE IN CONTRACT OR TORT, IRRESPECTIVE OF

FAULT, NEGLIGENCE OR STRICT LIABILITY OR WHETHER APC by Schneider Electric HAS BEEN

ADVISED IN ADVANCE OF THE POSSIBILITY OF SUCH DAMAGES. SPECIFICALLY, APC by

Schneider Electric IS NOT LIABLE FOR ANY COSTS, SUCH AS LOST PROFITS OR REVENUE,

LOSS OF EQUIPMENT, LOSS OF USE OF EQUIPMENT, LOSS OF SOFTWARE, LOSS OF DATA,

COSTS OF SUBSTITUENTS, CLAIMS BY THIRD PARTIES, OR OTHERWISE.

NO SALESMAN, EMPLOYEE OR AGENT OF APC by Schneider Electric IS AUTHORIZED TO ADD

TO OR VARY THE TERMS OF THIS WARRANTY. WARRANTY TERMS MAY BE MODIFIED, IF AT

ALL, ONLY IN WRITING SIGNED BY AN APC by Schneider Electric OFFICER AND LEGAL

DEPARTMENT.

Warranty claims

Customers with warranty claims issues may access the APC by Schneider Electric customer support

network through the Support page of the APC by Schneider Electric Web site, www.apc.com/support.

Select your country from the country selection pull-down menu at the top of the Web page. Select the

Support tab to obtain contact information for customer support in your region.

Radio Frequency Interference

USA.FCC

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant

to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful

interference when the equipment is operated in a commercial environment. This equipment generates,

uses, and can radiate radio frequency energy and, if not installed and used in accordance with this user

manual, may cause harmful interference to radio communications. Operation of this equipment in a

residential area is likely to cause harmful interference. The user will bear sole responsibility for correcting

such interference.

Canada.ICES

This Class A digital apparatus complies with Canadian ICES-003.

Cet appareil numérique de la classe A est conforme à la norme NMB-003 du Canada.

European Union

This product is in conformity with the Electromagnetic Compatibility (EMC) requirements set forth by the

EU directive 2014/30/EU of the European parliament and of the council of 26 February 2014 on the

harmonization of the laws of the Member States relating to electromagnetic compatibility.

This product has been tested and found to comply with the limits for Class A Information Technology

Equipment according to CISPR 32/EN 55032:2015 for Emissions and EN 55024:2010+A1:2015 for

Immunities.

Attention: This is a Class A product. In a domestic/residential environment this product may cause radio

interference in which the user may be required to take adequate measures.

Termékspecifikációk

Márka:	APC
Kategória:	Térfigyelő kamera
Modell:	NetBotz Camera Pod 165

Szüksége van segítségre?

Ha segítségre van szüksége APC NetBotz Camera Pod 165, tegyen fel kérdést alább, és más felhasználók válaszolnak Önnek

Az Ön neve*

Az Ön e-mail címe*

Írja ide kérdését

Útmutatók Térfigyelő kamera APC

APC NetBotz Camera Pod 160 Útmutató

2 Augusztus 2024

APC NetBotz NBWL0355 Útmutató

30 Július 2024

APC NetBotz Room Monitor 355 Útmutató

27 Július 2024

APC NBWL0356A Útmutató

27 Július 2024

APC NetBotz Room Monitor 455 Útmutató

24 Július 2024

APC NetBotz Camera Pod 165 Útmutató

19 Július 2024

APC NetBotz NBPD0160A Útmutató

7 Július 2024

Útmutatók Térfigyelő kamera

Legújabb útmutatók Térfigyelő kamera

Dahua Technology Pro IPC-HDPW5442G-Z Útmutató

15 Január 2025

Toshiba IKS-WR7412 Útmutató

14 Január 2025

Flir FC-610 O Útmutató

13 Január 2025

AVerMedia FC1320-P Útmutató

13 Január 2025

Digitus OptiMax DN-16037 Útmutató

13 Január 2025

Hikvision DS-2CE59U1T-AVPIT3ZF Útmutató

13 Január 2025

Hikvision IDS-2CD7526G0-IZHSY Útmutató

13 Január 2025

Hikvision DS-2CD2163G0-I(S) Útmutató

13 Január 2025

Hikvision DS-2CD2H83G1-IZS Útmutató

13 Január 2025

ZKTeco AntarVis 2.0 Útmutató

12 Január 2025