Használati útmutató Xena XA501

Olvassa el alább 📖 a magyar nyelvű használati útmutatót Xena XA501 (1 oldal) a Biztonság kategóriában. Ezt az útmutatót 3 ember találta hasznosnak és 2 felhasználó értékelte átlagosan 4.5 csillagra

Oldal 1/1
INSTRUCTIONS MANUAL XA501
DOOR SIREN ALARM with
programmable keypad
www.xenasecurity.com
Controls
1. Siren 4. Battery Low LED
2. Magnetic Contact 5. Battery Compartment
3. Keypad
Alarm unit battery
installation
1. The battery compartment is accessed from the rear
of the alarm unit by removing the screw from the
back and lifting the back cover B.
2. Insert four (4) ‘AAA’ size batteries (not included)
following the polarity C.
3. When the last battery is inserted the alarm will
beep very loudly to indicate that the batteries are
installed properly. Replace the back cover and fix
with screw. The Battery Low LED will light when
the batteries need replacing.
NOTE: After removing the batteries, press number 4
before installing new ones. The alarm must be
re-programmed with your security code each time the
batteries are removed or replaced.
Programming the alarm
Immediately after inserting the batteries the desired 4 digit
security code must be set, simply press the desired 4 digits
on the keypad.
Installation
Alarm
Place the alarm in the desired location, preferably on the
door or window with the screws or adhesive velcro tape
supplied.
Magnetic contact
The magnetic contact must be aligned to the same level
next to the alarm so that contact can be made when the
door is closed, either on the left or right hand side D.
Operation
When exiting from the protected area
Press keypad number 4 and a confirmation tone will
indicate that the alarm is armed. You have 30 seconds in
which to vacate the area. After this time, if the contact is
broken the alarm will sound.
When entering the protected area
Simply type your 4 digit security code within 10 seconds.
This will disarm the alarm.
Care and maintenance
To clean the case, simply use a soft slightly damp cloth
with water and wipe dry immediately.
CAUTION: Never use chemicals to clean the case, as they
may cause damage to the plastic and cause the alarm not
to function.
Troubleshooting
The unit does not sound when the batteries
are installed
Ensure that the batteries are connected correctly according
to the diagram in the battery compartment
The alarm does not arm
Ensure that the back plate of the alarm unit is secure to
hold the batteries in place and that the red light comes on
when the keypad buttons are pressed
The red light on the base of the alarm unit is on
This is the “Battery Low Indicator”. The batteries need
replacing
Battery precautions
When using this product follow these precautions at all times.
• Use only the appropriate size batteries
• Be sure to follow the correct polarity when installing
the batteries as indicated in the battery compartment.
Incorrect polarity may cause damage to the alarm.
• Do not mix different types of battery such as Alkaline
and Carbon-zinc or old batteries with new.
• If the alarm is not used for long periods of time,
remove the batteries to prevent damage or injury from
possible battery leakage.
• Do not recharge batteries not intended to be recharged
as they can overheat and rupture. (Always follow the
manufacturer’s directions.)
061107

Termékspecifikációk

Márka: Xena
Kategória: Biztonság
Modell: XA501

Szüksége van segítségre?

Ha segítségre van szüksége Xena XA501, tegyen fel kérdést alább, és más felhasználók válaszolnak Önnek




Útmutatók Biztonság Xena

Xena

Xena XA501 Útmutató

24 Augusztus 2024
Xena

Xena XA701 Útmutató

24 Augusztus 2024
Xena

Xena XA901 Útmutató

24 Augusztus 2024
Xena

Xena XA101 Útmutató

24 Augusztus 2024

Útmutatók Biztonság

Legújabb útmutatók Biztonság