Használati útmutató Xaoc Tirana

Xaoc nincs kategorizálva Tirana

Olvassa el alább 📖 a magyar nyelvű használati útmutatót Xaoc Tirana (4 oldal) a nincs kategorizálva kategóriában. Ezt az útmutatót 4 ember találta hasznosnak és 2 felhasználó értékelte átlagosan 4.5 csillagra

Letöltés PDF

Oldal 1/4

Thank you for purchasing the

Xaoc Devices product. The

Tirana module comes in handy

as a classic step sequencer,

modulation source, voltage

bank, arpeggiator etc., serv-

ing as the utility module for

supporting other sequencers,

but it also shines on its own

terms. Due to smart features

to be described in this manual,

Tirana provides a number of

very interesting possibilities,

and turns out to be surpris-

ingly powerful module, while

preserving the ease of use

and minimal real estate in

the system. It is only 6hp, and

therefore a perfect solution for

compact and portable modular

setups, but can empower just

any system to a great extent.

Clear 6hp space in your

eurorack cabinet and turn

the power off. Ensure that the

jumper on the in header re-

mains in place (for single unit

operation; for multiplied setups

read the instructions further

down in the manual). Now plug

in the ribbon cable to the bus

board, observing the red stripe

orientation. Tirana has been

secured against reversed power

connection but it is always a

good habit to pay attention to

this. Mount the screws and turn

your system back on.

In order to operate, an external

clock needs to be fed to the

clock input 3 – usually the

pulse from a LFO or any clock

generator of choice. Steps will

now be played subsequently in

a loop. Adjust the desired pitch

by turning knobs 1. Generated

pitch and trigger voltages are

available at cv out 8 and trig-

ger 7 sockets.

Each step may now be removed

from the sequence (muted) by

pressing the corresponding

button 2 . Please note that

only the trigger output is being

muted; the pitch voltage is

available as usual.

The sequence direction can be

changed by feeding a trigger

impulse into the direct. input

4. To reset the sequence, a

trigger needs to be fed into the

reset input 6.

The sequence can be also

transposed (offset) by provid-

ing control voltage into the

transp. input jack 5.

Each step can be repeated

up to 4 times (resulting in up

to 16 steps in the sequence).

To set a desired number of

repeats for a given step, hold its

mute button down for approx.

2 seconds until the menu mode

is conrmed by all buttons

dimmed for a moment. Then,

push the button no. 2 for one

repetition (2 note events),

but-

ton no. 3 for double repetition

(3 events) or button no. 4 for

triple repetition of the given step

(4 events). To reset the desired

step to generate just one note,

push button no. 1.

Tirana ships set to unipolar

0 to 10 V mode (as most users

will probably want to use it as

a melody generator). Still, the

module makes a great modula-

tion source when set to bipolar

-5 to +5V operation. To adjust

the desired mode, simply set

the jumper on the back of the

module.

You can easily chain up a

number of Tirana units together

to open up a lot of interesting

possibilities.

Every Tirana ships with one

10-pin ribbon cable and a loop

wire. Attach them exactly as

shown on the picture! First,

every slave unit requires jump-

ers to be removed (these are

required for single-unit opera-

tion). Then, every ribbon should

connect the out header of the

master unit with the in header

of slave unit. The rst unit in a

chain should only have the out

header occupied.

The single wire cable needs to

connect the lowest left pin of the

in header on the master unit,

and the same lowest left pin of

the out header on the last slave

unit in a chain.

Please double check that if it is

mounted correctly and put the

whole set in your cabinet. Don’t

forget about powering every

single Tirana unit.

• Build a 8, 12, 16, 32 (and lon-

ger) – step sequencer subsystem

using multiple Tiranas. The rst

unit in a linked chain acts as the

master, and this is where all the

patch cables should be fed. The

mutes and repetitions work for

each slave unit independently.

• Use one Tirana to transpose

the other one (unlinked) for

a pseudo arpeggio effect. Use

different divisions of the same

clock and step repeat function.

• Let one Tirana trigger the re-

set or direction change function

of another unit (unlinked).

• Use a couple of unlinked Ti-

ranas for complex sequencing:

feed them different clocks, com-

bine their trigger outputs with

Xaoc Bytom and CV outputs

with Xaoc Warna mixer.

• Make the trigger output a

source of complex clock for

another Tirana.

• Tirana comes in handy as an

utility clock divider. Feed a clock

and adjust the same repeat

setting on every step. Division is

available at the trigger output.

master

slave

Remove the jumper from

every module but master!

Then, attach supplied cables

exactly as shown on the

picture.

Termékspecifikációk

Márka:	Xaoc
Kategória:	nincs kategorizálva
Modell:	Tirana

Szüksége van segítségre?

Ha segítségre van szüksége Xaoc Tirana, tegyen fel kérdést alább, és más felhasználók válaszolnak Önnek

Az Ön neve*

Az Ön e-mail címe*

Írja ide kérdését

Útmutatók nincs kategorizálva Xaoc

Xaoc Ustka 1966 Útmutató

4 Szeptember 2024

Xaoc Batumi Útmutató

21 Augusztus 2024

Xaoc Poti Útmutató

21 Augusztus 2024

Xaoc Zadar Útmutató

21 Augusztus 2024

Xaoc Katowice Útmutató

21 Augusztus 2024

Xaoc Tirana Útmutató

21 Augusztus 2024

Xaoc Warna II Útmutató

21 Augusztus 2024

Xaoc DEVA Útmutató

21 Augusztus 2024

Xaoc Lipsk Útmutató

21 Augusztus 2024

Xaoc Praga Útmutató

21 Augusztus 2024

Útmutatók nincs kategorizálva

Legújabb útmutatók nincs kategorizálva

Einhell GE-EC 720 T Útmutató

5 December 2024

Ednet Quick Charge 3.0 Útmutató

5 December 2024

Ednet ED-85055 Útmutató

5 December 2024

Ednet ED-31521 Útmutató

5 December 2024

Ednet ED-31520 Útmutató

5 December 2024

Thermaltake Commander F6 RGB Útmutató

5 December 2024

Thermaltake H200 Útmutató

5 December 2024

Thermaltake TOUGHPOWER GF A3 Útmutató

5 December 2024

Livoo DOM478 Útmutató

5 December 2024

Daikin FTK20GVLT Útmutató

5 December 2024