Használati útmutató Worx WG401E

Worx gyalugép WG401E

Olvassa el alább 📖 a magyar nyelvű használati útmutatót Worx WG401E (12 oldal) a gyalugép kategóriában. Ezt az útmutatót 2 ember találta hasznosnak és 2 felhasználó értékelte átlagosan 4.5 csillagra

Letöltés PDF
Oldal 1/12
2
WARNING! Read all safety
warnings and all instructions.
Failure to follow the warnings and instructions
may result in electric shock, fire and/or serious
injury.
Save all warnings and instructions for
future reference.
- This appliance is not intended for use by
persons (including children) with reduced
physical, sensory or mental capabilities,
or lack of experience and knowledge,
unless they have been given supervision or
instruction concerning use of the appliance
by a person responsible for their safety.
- Children should be supervised to ensure
that they do not play with the appliance.
If the supply cord is damaged, it must be
replaced by the manufacturer, its service
agent or similarly qualified persons in order
to avoid a hazard.
SAFETY INSTRUCTIONS
IMPORTANT
READ CAREFULLY BEFORE USE
KEEP FOR FUTURE REFERENCE
SAFE OPERATING PRACTICES
1. TRAINING
Become familiar with the owner’s manual
before attempting to operate this equipment.
2. PREPARATION
1) Do not allow children to operate this
equipment.
2) Do not operate this equipment in the
vicinity of bystanders.
3) Wear ear protection and safety glasses at
all times while operating the machine.
4) Avoid wearing clothing that is loose fitting
or that has hanging cords or ties.
5) Only operate the machine in open space
(e.g. not close to a wall or other fixed
object) and on a firm, level surface.
6) Do not operate the machine on a paved or
gavel surface where ejected material could
cause injury;
7) Before starting the machine, check that all
screws, nuts, bolts, and other fasteners
are properly secured and that guards and
screens are in place. Replace damaged or
unreadable labels.
3. OPERATION
1) Before starting the machine, look into the
feeding chamber to make certain that it is
empty.
2) Keep your face and body away from the
feed intake opening.
3) Do not allow hands or any other part of
the body or clothing inside the feeding
chamber, discharge chute, or near any
moving part.
4) Keep proper balance and footing at all
times. Do not overreach. Never stand at a
higher level than the base of the machine
when feeding material into it.
5) Always stand clear of the discharge zone
when operating this machine.
6) When feeding material into the machine
be extremely careful that pieces of metals,
rocks, bottles, cans or other foreign objects
are not included.
7) If the cutting mechanism strikes any foreign
objects or if the machine should start
making any unusual noise or vibration,
switch off the machine, disconnect the
supply and take the following steps:
 •Inspectfordamage;
 •Checkforandtightenanylooseparts;
 •Haveanydamagedpartsreplacedor
repaired with parts having equivalent
specifications.
8) Do not allow processed material to build
up in the discharge zone; this may prevent
proper discharge and can result in kickback
of material through the feed intake
opening;
9) If the machine becomes clogged, shut off
the power source and disconnect from
supply before cleaning debris. Keep the
power source clear of debris and other
accumulations to prevent damage to the
power source or possible fire. Remember
that operating the starting mechanism on
engine powered machines will still cause
3
the cutting means to move.
10) Keep all guards and deflectors in place and
in good working condition;
11) Do not tamper with the power source
governor settings; the governor controls
the safe maximum operating speed and
protects the power source and all moving
parts from damage caused by over-speed.
Seek authorized service if a problem exists.
12) Do not transport this machine while the
power source is running.
13) Shut off the power source and disconnect
the plug whenever you leave the work area.
14) Do not tilt the machine while the power
source is running.
4. MAINteNANce AND StoRAGe
1) When the machine is stopped for servicing,
inspection, or storage, or to change an
accessory, shut off the power source,
disconnect form supply, make sure that all
moving parts have come to a complete stop
and, where a key is fitted remove the key.
Allow the machine to cool before making
any inspections, adjustments, etc.
2) When servicing the cutting means be aware
that, even though the power source will
not start due to the interlock feature of the
guard, the cutting means can still be moved
by a manual starting mechanism.
5. ADDItIoNAL SAfety INStRuctIoNS
foR uNItS WIth BAGGING
AttAchMeNtS
1) Shut-off the power unit before attaching or
removing the bag;
Read the instruction manual,
before use.
Keep bystander or children away.
Danger - Rotating blades. Keep
hands and feet out of openings
while machine is running.
Wear eye and ear protection.
Remove plug from the mains
immediately if the cable is
damaged or cut
Double insulation
Wait until all machines
components have completely
stopped before touching them.
Do not use as a step
RCM approval mark

Termékspecifikációk

Márka: Worx
Kategória: gyalugép
Modell: WG401E

Szüksége van segítségre?

Ha segítségre van szüksége Worx WG401E, tegyen fel kérdést alább, és más felhasználók válaszolnak Önnek


Útmutatók gyalugép Worx

Worx

Worx WX625 Útmutató

21 Július 2024
Worx

Worx WX623 Útmutató

15 Július 2024
Worx

Worx WG401E Útmutató

8 Július 2024

Útmutatók gyalugép

Legújabb útmutatók gyalugép

Einhell

Einhell EHM 1300 Útmutató

5 December 2024
Einhell

Einhell RT-SP 260 D Útmutató

5 December 2024
Protool

Protool PLP 24 Útmutató

20 Szeptember 2024
HiKOKI

HiKOKI P20SFWAZ Útmutató

16 Szeptember 2024
Einhell

Einhell Expert TE-PL 18/82 Li Útmutató

5 Szeptember 2024
Einhell

Einhell TC-PL 900 Útmutató

5 Szeptember 2024
Einhell

Einhell RTB-003 Útmutató

5 Szeptember 2024
Einhell

Einhell LOF 850 E Útmutató

5 Szeptember 2024
Einhell

Einhell E-HO 900 Útmutató

2 Szeptember 2024
Einhell

Einhell E-OF 1200 Útmutató

2 Szeptember 2024