Használati útmutató Vemer Simply AST

Vemer kapcsoló Simply AST

Olvassa el alább 📖 a magyar nyelvű használati útmutatót Vemer Simply AST (1 oldal) a kapcsoló kategóriában. Ezt az útmutatót 2 ember találta hasznosnak és 2 felhasználó értékelte átlagosan 4.5 csillagra

Letöltés PDF

Oldal 1/1

4DISPLAY DESCRIPTION

3CONNECTION DIAGRAM

DIMENSIONS

INSTALLATION

PROGRAMMING

DEPLETED BATTERY

RELAY MANUAL SWITCHING

DEFAULT PARAMETERS

7ADVANCED PROGRAMMING

REFERENCE STANDARDS

Compliance with Community directives:

2014/35/EU (LVD), 2014/30/EU (E.M.C.D.)

is declared in reference to the following harmonised standards:

• EN 60730-2-7

1User manual

ASTRONOMICAL TWILIGHT SWITCHES WITH TRIPPERS

 Read all instructions carefully

V3IS00780-021

Mod. Simply AST

Simply AST is an astronomical twilight switch used to manage electric

utilities between sunset and sunrise which are automatically calculated by the

instrument based on the geographical coordinates inserted (for Italy only the

telephone area code).

The trippers permit you to set one or more intervals in which the load turn off.

The cover on the back of the instrument allows battery replacement once

depleted.

Simply AST is an electronic device that performs 1B type actions designed

for use in place with over-voltage category III and pollution degree 2, as per

standards EN 60730-1.

Code Model Description

VE707600 Simply AST Astronomical twilight switches with trippers

SAFETY WARNINGS

During product installation and operation it is necessary to observe the

following instructions:

1) The instrument must be installed by a qualified person, in strict compliance

with the connection diagrams.

2) Do not power the product if any part of it is damaged.

3) The instrument must be installed and activated in compliance with current

electric system standards.

4) The electrical system in the building in which the instrument is to be installed

should have an over-current switch and a protection device.

5) Before accessing the connection terminals, verify that the leads are not live.

6) After installation, inaccessibility to the connection terminals without

appropriate tools must be guaranteed.

7) In case of malfunction do not perform repairs and contact immediately the

technical support.

TECHNICAL CHARACTERISTICS

• Power supply: 230 Vac (-15% ÷ +10%) 50/60 Hz

• Absorption: 6 VA (1W)

• Output: relay with change-over monostable contact from 16 A / 250 Vac

• Terminals for max 6 mm

2 cable section

• Minimum interval for turning-off in the night: 30 minutes

• Summer/winter time automatic update (removable) depending on the

geographical zone of installation

• Active backlight display with mains power

• Replaceable CR2032 type backup battery (duration: 5 years about)

• Operating temperature: -20 ÷ +50 °C

• Storage temperature: -25 ÷ +70 °C

• Operating humidity: 20÷90% non condensing

• Container: 2 DIN modules

• Degree of protection: IP20

• Insulation: reinforced among accessible parts (frontal) and all other terminals

PRG

16A / 250V

 Current time indication

2 Set year, month, day indication (displayed in advanced programming)

3 Set programming

4 Relay status

5 Switchings lock of active relay

6 Active programming menu (PROG)

7 Active advanced programming menu (SET)

Note: the tripper that corresponds to the

current time flashes.

Little tripper: relay OFF (position 6-7)

Big tripper: relay ON (position 7-8)

09-2020

Vemer S.p.A.

I - 32032 Feltre (BL) • Via Camp Lonc, 16

e-mail: info@vemer.it - web site: www.vemer.it

• The instrument is provides with the inserted battery and the set date

•

Connect the load and the power supply as illustrated in section “Connection

diagram”. The backlight will turn on as soon as the instrument is powered and

remains always on (in the presence of mains power).

• For operating, the installation location must be set:

- press any key: the instrument requires you to set the location (for Italy only

the telephone area code, for the other states the geographic coordinates are

required)

- when the installation position is set, the instrument is able to calculate

automatically the sunrise and sunset time for each day during the year. The

instrument will turn on the load at the sunset and turn off it at the sunrise.

Note: if any position isn’t set, all the internal trippers will flashing and

the relay will remain off.

When the backup battery is low, the instrument displays alternating

with the main page. In this condition, replace the battery as soon as possible, by

accessing the battery compartment at the back of the instrument, to avoid that,

in case of blackout, the date and time are lost.

In this condition, when mains power return, display will flash, the time start from

00:00 of 01.01.2014 and the relay stays in OFF position.

In this case, to resume the normal operating, set time and date.

Dispose of used batteries in accordance with the current legal

provisions regarding the disposal of hazardous waste.

Attention: before you access the battery compartment, disconnect the power supply.

Attention: perform the operation in a maximum time of one minute in order not

to lose date and time. Use only CR-2032 type battery.

The default of the parameters shows the instrument factory

conditions, that is to say

- position: none

- geographical zone: 1 (Europe)

- winter time automatic change: active

- programming: ON at sunset, OFF at sunrise

- sunrise and sunset time adjust: 0

To perform the default, from the main screen press simultaneously for at least

3 seconds the keys , PRG and

and, during flashing, confirm by

pressing PRG key.

Attention: if during flashing you don’t press any key within 5 seconds, the

instrument returns to the main screen without perform the reset.

Note: after default, all the internal trippers will flash. Press any key to set the

location (see box 5 – Installation).

To change manually the status of relay output (from ON to OFF or vice versa)

press the

key.

Attention: the status is maintained until new press of the

key

or until the next

program switching.

To lock the current status of the relay and prevent its switchings, press for a long

time (> 3 seconds) the key

. In this condition the symbol is lit.

Unlocking is done by pressing for a long time the

key.

Note: the monostable relay

switches only if the

instrument is mains

powered.

From the main screen by pressing for a long time (> 3 seconds)

PRG key, it’s possible to access to the advanced programming, to set:

- location where instrument is installed (geographical coordinates or, for Italy only, the telephone area code)

- sunrise and sunset time correction. This function is used to change the sunrise and sunset time that is automatically calculated by the

instrument (maximum correction ±120 minutes)

- date and time

- summertime automatic update

- geographical zone of installation (needed to determine when the summer/winter time changes).

Simply AST programming consists of a single program to be repeated every day,

according to which the output is in the ON position between the time of sunset and the

time of sunrise and in the OFF position between sunrise and sunset.

Note: activation and deactivation of the load occur exactly at the sunset and sunrise

time; the trippers containing those times are ON (big trippers).

Note: you can exit programming even if you don’t press any key within the time-out

(40 seconds if the instrument is mains powered, 10 seconds if powered by the backup

battery). The modifications are still saved.

Display date, sunrise and sunset time

From the main page, by pressing the key it’s possible to display the current date

and the sunrise and sunset time.

Before each parameter an identification abbreviation is displayed ( for date, Date

rise set for sunrise and for sunset).

At the end the instrument return to the main page.

OFF

Sunset Sunrise

OFF

Sunset Sunrise

Between sunset and sunrise it is possible to set one or more intervals with

minimum duration of 30 minutes in which the output relay will be off:

1. from the main page press PRG key.

2. the programming starts from the first tripper into the interval between sunset

and sunrise

3. press the key or to set the tripper ( = relay on, = relay off) and

press PRG to confirm and step up of 30 minutes (the next tripper)

4. once the desired programming is got, press

PRG key for at least 3 seconds to exit

and return to the main page.

Note: from dawn to dusk no switching is performed and the relay is forced to

remain in the off status.

(*) summer/winter time change

If the automatic update of summer time is active (on), the change occurs according

to the set geographical zone:

Zone Start DST (+1h) End DST (-1h)

01 Europe Last Sunday, March Last Sunday, October

02 North America Second Sunday, March First Sunday, November

03 Australia First Sunday, October First Sunday, April

04 Chile Second Sunday, October Second Sunday, March

05 New Zealand Last Sunday, September First Sunday, April

Note: time change is fixed for all zones at 2:00 o’clock for the start of DST and at

3:00 o’clock for the end of DST.

(**) If the instrument is installed in Italy, geographical zone setting are not required.

PRG

PRG PRG

PRG

PRG PRG PRG

PRG

ITALY

PRG

Latitude setting

Year setting Month setting Day setting Time setting

Minute setting Summer/winter time change* Geographical zone setting**

00 = Every other state

Location setting

Longitude setting

Sunrise time correction ± 2:00h.

Use negative values to advance the event,

positive values to delay the event

Sunset time correction ± 2:00h.

Use negative values to advance the event,

positive values to delay the event

Time zone setting

Main page Programming menu Programming menu

02 = Milano

06 = Roma

010 = Genova

........ .....

0985 = Scalea

North latitude East longitude Positive time zone

Negative time zoneWest longitudeSouth latitude

Termékspecifikációk

Márka:	Vemer
Kategória:	kapcsoló
Modell:	Simply AST

Szüksége van segítségre?

Ha segítségre van szüksége Vemer Simply AST, tegyen fel kérdést alább, és más felhasználók válaszolnak Önnek

Az Ön neve*

Az Ön e-mail címe*

Írja ide kérdését

Útmutatók kapcsoló Vemer

Vemer micro BT Útmutató

4 Január 2025

Vemer Quicklux-3F Útmutató

14 Szeptember 2024

Vemer memo BT2 Útmutató

25 Augusztus 2024

Vemer memo Wi-Fi Útmutató

10 Augusztus 2024

Vemer NAPA Útmutató

7 Augusztus 2024

Vemer AGMA22 Útmutató

6 Augusztus 2024

Vemer DUET-W Útmutató

5 Augusztus 2024

Vemer MAC3 Útmutató

4 Augusztus 2024

Vemer Quicklux-4F Útmutató

4 Augusztus 2024

Vemer KEY Útmutató

2 Augusztus 2024

Útmutatók kapcsoló

Legújabb útmutatók kapcsoló

Tork SS700ZA Útmutató

9 Április 2025

Cudy FS1024 Útmutató

9 Április 2025

Lancom GS-2412 Útmutató

5 Április 2025

Lancom GS-2412P Útmutató

5 Április 2025

Lancom GS-2426 Útmutató

5 Április 2025

Lancom GS-2426P Útmutató

5 Április 2025

Hager ARF970D Útmutató

3 Április 2025

Hager ARF920D Útmutató

3 Április 2025

Fantini Cosmi B12BN Útmutató

2 Április 2025

Fantini Cosmi B12DN Útmutató

2 Április 2025