Használati útmutató Tru Components TK4S-14RC

Tru Components Termosztát TK4S-14RC

Olvassa el alább 📖 a magyar nyelvű használati útmutatót Tru Components TK4S-14RC (2 oldal) a Termosztát kategóriában. Ezt az útmutatót 2 ember találta hasznosnak és 2 felhasználó értékelte átlagosan 4.5 csillagra

Letöltés PDF

Oldal 1/2

Read and understand the instruction manual before using the product.

For your safety, read and follow the below safety considerations before using. For your safety,

read and follow the considerations written in the instruction manual.

Keep this instruction manual in a place where you can find easily.

The specifications, dimensions, etc are subject to change without notice for product improvement.

Safety Considerations

• Observe all ‘Safety Considerations’ for safe and proper operation to avoid hazards.

• symbol indicates caution due to special circumstances in which hazards may occur.

Warning Failure to follow instructions may result in serious injury or death

01. Fail-safe device must be installed when using the unit with machinery that may cause

serious injury or substantial economic loss.(e.g. nuclear power control, medical equipment,

ships, vehicles, railways, aircraft, combustion apparatus, safety equipment, crime/disaster

prevention devices, etc.)

Failure to follow this instruction may result in personal injury, economic loss or fire.

02. Do not use the unit in the place where flammable/explosive/corrosive gas, high humidity,

direct sunlight, radiant heat, vibration, impact or salinity may be present.

Failure to follow this instruction may result in explosion or fire.

03. Install on a device panel to use.

Failure to follow this instruction may result in electric shock.

04. Do not connect, repair, or inspect the unit while connected to a power source.

Failure to follow this instruction may result in fire or electric shock.

05. Check ‘Connections’ before wiring.

Failure to follow this instruction may result in fire.

06. Do not disassemble or modify the unit.

Failure to follow this instruction may result in fire or electric shock.

Caution Failure to follow instructions may result in injury or product damage

01. When connecting the power input and relay output, use AWG 20 (0.50 mm 2) cable or over, and

tighten the terminal screw with a tightening torque of 0.74 to 0.90 N m.

When connecting the sensor input and communication cable without dedicated cable, use

AWG 28 to 16 cable and tighten the terminal screw with a tightening torque of 0.74 to 0.90 N

Failure to follow this instruction may result in fire or malfunction due to contact failure.

02. Use the unit within the rated specifications.

Failure to follow this instruction may result in fire or product damage

03. Use a dry cloth to clean the unit, and do not use water or organic solvent.

Failure to follow this instruction may result in fire or electric shock.

04. Keep the product away from metal chip, dust, and wire residue which flow into the unit.

Failure to follow this instruction may result in fire or product damage.

Cautions during Use

• Follow instructions in ‘Cautions during Use’. Otherwise, it may cause unexpected accidents.

• Check the polarity of the terminals before wiring the temperature sensor. For RTD temperature sensor,

wire it as 3-wire type, using cables in same thickness and length.

For thermocouple (TC) temperature sensor, use the designated compensation wire for extending wire.

• Keep away from high voltage lines or power lines to prevent inductive noise. In case installing power

line and input signal line closely, use line filter or varistor at power line and shielded wire at input

signal line. Do not use near the equipment which generates strong magnetic force or high frequency

noise.

• Do not apply excessive power when connecting or disconnecting the connectors of the product.

• Install a power switch or circuit breaker in the easily accessible place for supplying or disconnecting

the power.

• Do not use the unit for other purpose (e.g. voltmeter, ammeter), but temperature controller.

• When changing the input sensor, turn off the power first before changing. After changing the input

sensor, modify the value of the corresponding parameter.

• Do not overlapping communication line and power line. Use twisted pair wire for communication line

and connect ferrite bead at each end of line to reduce the effect of external noise.

• Make a required space around the unit for radiation of heat. For accurate temperature measurement,

warm up the unit over 20 min after turning on the power.

• Make sure that power supply voltage reaches to the rated voltage within 2 sec after supplying power.

• Do not wire to terminals which are not used.

• This unit may be used in the following environments.

-Indoors (in the environment condition rated in ‘Specifications’)

-Altitude Max. 2,000 m

-Pollution degree 2

-Installation category II

Product Components

• Product (+ bracket) • Instruction manual

Operating Instructions for download

Use the link www.conrad.com/downloads (alternatively scan the QR code) to download the complete

operating instructions (or new/current versions if available). Follow the instructions on the web page.

Specifications

Series TK4S

Power supply AC type 100 - 240 VAC~ 50/60 Hz

Permissible voltage range 90 to 110 % of rated voltage

Power

consumption AC type ≤ 8 VA

Unit weight (packaged) ≈ 105 g

(≈ 150 g)

Sampling period 50 ms

Input specification Refer to 'Input Type and Using Range'

Control

output

Relay 250 VAC ~ 3 A, 30 VDC 3 A 1a

SSR 11 VDC ±2 V, ≤ 20 mA

Current DC 4-20 mA or DC 0-20 mA (parameter), Load resistance: ≤ 500 Ω

Alarm

output Relay AL1: 250 VAC~ 3 A 1a

Display type 7 segment (red, green, yellow), LED type

Control

type

Heating, Cooling

ON/OFF, P, PI, PD, PID Control

Heating & Cooling

Hysteresis • Thermocouple, RTD: 1 to 100 (0.1 to 100.0) °C/°F

• Analog: 1 to 100 digit

Proportional band (P) 0.1 to 999.9 °C/°F (0.1 to 999.9%)

Integral time (I) 0 to 9,999 sec

Derivative time (D) 0 to 9,999 sec

Control cycle (T) • Relay output, SSR drive output: 0.1 to 120.0 sec

• Selectable current or SSR drive output: 1.0 to 120.0 sec

Manual reset 0.0 to 100.0%

Relay life

cycle

Mechanical OUT1/2: ≥ 5,000,000 operations

AL1/2: ≥ 20,000,000 operations

Electrical ≥ 100,000 operations

Dielectric strength Dependent on the power supply

AC voltage type Between the charging part and the case: 3,000 VAC ~ 50/60 Hz for 1 minute

Vibration 0.75 mm amplitude at frequency of 5 to 55 Hz in each X, Y, Z direction for

2 hours

Insulation resistance ≥ 100 MΩ (500 VDC megger)

Noise immunity ±2 kV square shaped noise by noise simulator (pulse width: 1 µs) R-phase,

S-phase

Memory retention ≈ 10 years (non-volatile semiconductor memory type)

Ambient temperature -10 to 50 °C, storage: -20 to 60 °C (no freezing or condensation)

Ambient humidity 35 to 85%RH, storage: 35 to 85%RH (no freezing or condensation)

Protection structure IP65 (Front panel, IEC standards)

Insulation type Double insulation or reinforced insulation (mark: , dielectric strength

between the measuring input part and the power part: 2 kV)

Certification

Input Type and Using Range

The setting range of some parameters is limited when using the decimal point display.

Input type Decimal

point Display Using range (°C) Using range (°F)

Thermo

-couple

K (CA) 1 -200 to 1,350 to 2,462-328

0.1 -199.9 to 999.9 -199.9 to 999.9

J (IC) 1 -200 to to 1,472800 -328

0.1 -199.9 to -199.9 to 999.9800.0

E (CR) 1 -200 to to 1,472800 -328

0.1 -199.9 to -199.9 to 999.9800.0

T (CC) 1 -200 to 400 to 752-328

0.1 -199.9 to 400.0 -199.9 to 752.0

B (PR) 1 0 to 32 to 3,2721,800

R (PR) 1 0 to 1,750 32 to 3,182

S (PR) 1 0 to 1,750 32 to 3,182

N (NN) 1 -200 to 1,300 to 2,372-328

C (TT) 01) 1 0 to 2,300 32 to 4,172

G (TT) 02) 1 0 to 2,300 32 to 4,172

L (IC) 1 -200 to 900 to 1,652-328

0.1 -199.9 to 900.0 -199.9 to 999.9

U (CC) 1 -200 to 400 to 752-328

0.1 -199.9 to 400.0 -199.9 to 752.0

Platinel II 1 0 to 1,390 32 to 2,534

RTD

Cu50 Ω 0.1 -199.9 to 200.0 -199.9 to 392.0

Cu100 Ω 0.1 -199.9 to 200.0 -199.9 to 392.0

JPt100 Ω 1 -200 to 650 to 1,202-328

0.1 -199.9 to 650.0 -199.9 to 999.9

DPt50 Ω 0.1 -199.9 to 600.0 -199.9 to 999.9

DPt100 Ω 1 -200 to 650 to 1,202-328

0.1 -199.9 to 650.0 -199.9 to 999.9

Nickel120 Ω -801 to 200 -112 to 392

Analog

0 to 10 V - 0 to 10 V

0 to 5 V - 0 to 5 V

1 to 5 V - 1 to 5 V

0 to 100 mV - 0 to 100 mV

0 to 20 mA - 0 to 20 mA

4 to 20 mA - 4 to 20 mA

01) C (TT): Same as existing W5 (TT) type sensor

02) G (TT): Same as existing W (TT) type sensor

• Permissible line resistance per line: ≤ 5 Ω

■Display accuracy

Input type Using temperature Display accuracy

Thermo

-couple RTD

At room temperature

(23 °C ±5 °C)

(PV ±0.3% or ±1 °C higher one) ±1-digit

• Thermocouple K, J, T, N, E below -100 °C and L, U, PLII,

RTD Cu50 Ω, DPt50 Ω:

(PV ±0.3% or ±2 °C higher one) ±1-digit

• Thermocouple C, G and R, S below 200 °C:

(PV ±0.3% or ±3 °C higher one) ±1-digit

• Thermocouple B below 400 °C:

There is no accuracy standards

Out of room temperature

range

(PV ±0.5% or ±2 °C higher one) ±1-digit

• RTD Cu50 Ω, DPt50 Ω:

(PV ±0.5% or ±3 °C higher one) ±1-digit

• Thermocouple R, S, B, C, G:

(PV ±0.5% or ±5 °C higher one) ±1-digit

• Other sensors: ≤ ±5 °C (≤-100 °C)

Analog

At room temperature

(23 °C ±5 °C) ±0.3% F.S. ±1-digit

Out of room temperature

range ±0.5% F.S. ±1-digit

Unit Descriptions

1. PV display part (Red)

• Run mode: Displays PV (Present value).

• Setting mode: Displays parameter name.

2. SV display part (Green)

• Run mode: Displays SV (Setting value).

• Setting mode: Displays parameter setting value.

3. Input key

Display Name

[A/M] Control switching key

[MODE] Mode key

[◄], [▼], [▲] Setting value control key

4. Indicator

Display Name Description

°C, %, °F Unit Displays selected unit (parameter)

AT Auto tuning Flashes during auto tuning every 1 sec

OUT1/2 Control

output

Turns ON when the control output is ON

• SSR output (cycle/phase control)

MV over 5% ON

• Current output

Manual control: 0% OFF, over ON

Auto control: below 2% OFF, over 3% ON

AL1 Alarm

output Turns ON when the alarm output is ON

MAN Manual

control Turns ON during manual control

SV1/2/3 Multi SV The SV indicator is ON which is currently

displayed. (When using multi SV function)

TK4S

5. PC loader port:

For connecting

communication

converter (SCM series).

Dimensions

• Unit: mm

■ Panel cut-out

Body Panel cut-out

A B C D E F G H I J

TK4S 48 48 ≥65 ≥656 64.5 1.7 45 45 +0.6

045 +0.6

■Bracket

TK4S

Simultaneous Heating & Cooling

Output PID Temperature Controller

TK4S-14RC

Item no.: 3016144

INSTRUCTION MANUAL

TCD210240AD

Installation Method

■TK4S

Flathead screwdriver

After mounting the product to panel with bracket, insert the unit into a panel, fasten the bracket by

pushing with a flathead screwdriver.

Errors

Display Input Description Output Troubleshooting

Temperature

sensor

Flashes at 0.5 sec interval

when input sensor is

disconnected or sensor is not

connected.

'Sensor error, MV'

parameter setting

value

Check input sensor

status.

Analog Flashes at 0.5 sec interval

when input is over F.S. ±10%.

'Sensor error, MV'

parameter setting

value

Check analog input

status.

Temperature

sensor

Flashes at 0.5 sec intervals if

the input value is above the

input range.

01)

Heating: 0%,

Cooling: 100%

When input is within

the rated input

range, this display

disappears.

Analog Flashes at 0.5 sec intervals if

the input value is over 5 to 10%

of high limit or low limit value.

Normal output

Temperature

sensor

Flashes at 0.5 sec. intervals

if the input value is below the

input range.

01)

Heating: 100%,

Cooling: 0%

Analog

Flashes at 0.5 sec intervals if

the input value is over 5 to 10%

of low limit or high limit value. Normal output

Temperature

sensor

Flashes at 0.5 sec intervals if

there is error for setting and

it returns to the error-before

screen.

- Check setting method.

Analog

01) Be careful that when / error occurs, the control output may occur by recognizing the maximum or minimum input

depending on the control type.

Connections

• Shaded terminals are standard model.

• Digital input is not electrically insulated from internal circuits, so it should be insulated when

connecting other circuits.

■TK4S

Crimp Terminal Specifications

• Unit: mm, use the crimp terminal of the following shape.

≥3.0

≤5.8

≥3.0

≤5.8

Fork crimp terminal Round crimp terminal

Initial Display When Power is ON

When power is supplied, after all display will flash for 1 sec, model name is displayed sequentially. After

input sensor type will flash twice, enter into RUN mode.

1. All display 2. Model 3. Input

specification 4. Run mode

PV display part

SV display part

Mode Setting

RUN

Auto before entering

to mode (when using

password)

Move digits: [◄]

Change value: [▲], [▼]

Save: [MODE] or no

key input over 5 sec

Password Key input Entering mode

Pass Auto Selected mode

Fail [◄], [▲], [▼] Password input

[MODE] Run mode

[MODE] over 3 sec

Refer to ‘Parameter Reset’

[A/M]

Auto

[◄], [▲], [▼]

Password input

SV setting

Parameter group

Parameter reset

Auto/Manual control

switching

Digital input key

[MODE] over 2 sec

[◄] + [▲] + [▼] over 5 sec

[▲] + [▼] over 3 sec

[A/M] 01)

01) In case of TK4S model, short press of [MODE] key replaces [A/M] key function.

Parameter Reset

01. Pressthe[◄]+[▲]+[▼]keysforover5sec.inrunmode,INITturnsON.

02. ChangethesettingvalueasYESbypressingthe[▲],[▼]keys.

03. Pressthe[MODE]keytoresetallparametervaluesasdefaultandtoreturntorunmode.

Parameter Setting

• Some parameters are activated/deactivated depending on the model or setting of other parameters.

• The 'Parameter mask' feature hides unnecessary or inactive parameters, and the 'User parameter

group' feature quickly and easily sets up certain parameters that are frequently used.

• Refer to the user manual for the details.

Disposal

This symbol must appear on any electrical and electronic equipment placed on the EU

market. This symbol indicates that this device should not be disposed of as unsorted

municipal waste at the end of its service life.

Owners of WEEE (Waste from Electrical and Electronic Equipment) shall dispose of it

separately from unsorted municipal waste. Spent batteries and accumulators, which are not

enclosed by the WEEE, as well as lamps that can be removed from the WEEE in a non-

destructive manner, must be removed by end users from the WEEE in a non-destructive

manner before it is handed over to a collection point.

Distributors of electrical and electronic equipment are legally obliged to provide free take-back of waste.

Conrad provides the following return options free of charge (more details on our website):

• in our Conrad offices

• at the Conrad collection points

• at the collection points of public waste management authorities or the collection points set up by

manufacturers or distributors within the meaning of the ElektroG

End users are responsible for deleting personal data from the WEEE to be disposed of.

It should be noted that different obligations about the return or recycling of WEEE may apply in countries

outside of Germany.

■ Parameter 1 group

Parameter Display Default

Control output RUN/STOP

Multi SV selection

Heater current monitoring

Alarm output1 low limit

Alarm output1 high limit

Multi SV 0

Multi SV 1

Multi SV 2

Multi SV 3

■ Parameter 2 group

Parameter Display Default

Auto tuning RUN/STOP

Heating proportional band

Cooling proportional band

Heating integral time

Cooling integral time

Heating derivative time

Cooling derivative time

Dead overlap band

Manual reset

Heating hysteresis

Heating OFF offset

Cooling hysteresis

Cooling OFF offset

MV low limit

MV high limit

RAMP up change rate

RAMP down change rate

RAMP time unit

■ Parameter 3 group

Parameter Display Default

Input specification

Temperature unit

Analog low limit

Analog high limit

Scaling decimal point

Low limit scale

High limit scale

Display unit

Input correction

Input digital filter

SV low limit

SV high limit

Control output mode (Normal type)

(Heating& Cooling type)

Control type (Normal type)

(Heating& Cooling-type)

Auto tuning mode

OUT1 control output selection

OUT2 control output selection

OUT2 current output range

Heating control cycle

(Relay)

(SSR)

Cooling control cycle

■ Parameter 4 group

Parameter Display Default

Alarm output1 Operation mode

Alarm output1 Option

Alarm output1 Hysteresis

Alarm output1 contact type

Alarm output1 ON delay time

Alarm output1 OFF delay time

LBA time

LBA band

Analog Transmission output1 Mode

Transmission output1 low limit

Transmission output1 high limit

Analog Transmission output2 Mode

Transmission output2 low limit

Transmission output2 high limit

Communication address

Communication speed

Comm. parity bit

Comm. stop bit

Response time

Comm. write

■ Parameter 5 group

Parameter Display Default

Multi SV number

Digital input key

Digital input1 Terminal Function

Digital input2 Terminal Function

Manual control, initial MV

Manual control, preset MV

Sensor error MV

Control stop MV

Control stop alarm output

User level

SV setting lock

Parameter 1 group lock

Parameter 2 group lock

Parameter 3 group lock

Parameter 4 group lock

Parameter 5 group lock

Password setting

This is a publication by Conrad Electronic SE, Klaus-Conrad-Str. 1, D-92240 Hirschau (www.conrad.com).

All rights including translation reserved. Reproduction by any method, e.g. photocopy, microlming, or the

capture in electronic data processing systems require the prior written approval by the editor. Reprinting, also

in part, is prohibited. This publication represents the technical status at the time of printing.

*BN3016144_TK4S-14RC_INST_W_V1_EN_20240417

Termékspecifikációk

Márka:	Tru Components
Kategória:	Termosztát
Modell:	TK4S-14RC

Szüksége van segítségre?

Ha segítségre van szüksége Tru Components TK4S-14RC, tegyen fel kérdést alább, és más felhasználók válaszolnak Önnek

Az Ön neve*

Az Ön e-mail címe*

Írja ide kérdését

Útmutatók Termosztát Tru Components

Tru Components TX4S-14R Útmutató

18 December 2024

Tru Components TK4S-14RC Útmutató

18 December 2024

Tru Components TCN4S-24R Útmutató

18 December 2024

Tru Components TC-7T.81-240NC Útmutató

26 Augusztus 2024

Tru Components TC-7T.81-230NO Útmutató

26 Augusztus 2024

Tru Components TC-FKS011NO Útmutató

26 Augusztus 2024

Tru Components TC-ZR011 Útmutató

26 Augusztus 2024

Tru Components TC-FKO011NC Útmutató

26 Augusztus 2024

Útmutatók Termosztát

Legújabb útmutatók Termosztát

ATTACK OT80 Útmutató

19 December 2024

EQ-3 HmIP-WTH-2 Útmutató

17 December 2024

EQ-3 HMIP-WTH Útmutató

17 December 2024

EQ-3 HMIP-eTRV Útmutató

17 December 2024

EQ-3 HM-TC-IT-WM-W-EU Útmutató

17 December 2024

EQ-3 HM-CC-RT-DN Útmutató

17 December 2024

EQ-3 HMIP-BWTH Útmutató

17 December 2024

EQ-3 HMIP-BWTH24 Útmutató

17 December 2024

EQ-3 131651A0 Útmutató

17 December 2024

EQ-3 HmIP-eTRV-B Útmutató

17 December 2024