Használati útmutató Toolland PH360

Toolland vágógép PH360

Olvassa el alább 📖 a magyar nyelvű használati útmutatót Toolland PH360 (17 oldal) a vágógép kategóriában. Ezt az útmutatót 3 ember találta hasznosnak és 2 felhasználó értékelte átlagosan 4.5 csillagra

Letöltés PDF

Oldal 1/17

PH340/PH360

USER MANUAL 2

HANDLEIDING 4

MODE D'EMPLOI 6

MANUAL DEL USUARIO 8

BEDIENUNGSANLEITUNG 10

INSTRUKCJA OBSŁUGI 12

MANUAL DO UTILIZADOR 14

PH340/PH360

V. 01 05/12/2018 2 ©Velleman nv –

USER MANUAL

1. Introduction

Thank you for choosing Toolland. Please read the manual thoroughly before bringing this

device into service. If the device was damaged in transit, do not install or use it and contact

your dealer.

Refer to the Velleman® Service and Quality Warranty on the last pages of this manual.

2. Safety Instructions

Safety gloves are required while operating this machine.

 CAUTION The edges of cut tiles are sharp. –

 Always keep the appliance away from any crash and corrosive liquid.

 This tile-cutting machine is fitted with a replaceable circular blade. Keep the tile cutter and

blade away from children.

 After use, the appliance must be stored in a safe and dry place.

 This appliance is designed for cutting and breaking glazed tile, and shall not be used for

any other purpose.

 When using the appliance, always keep extension leads away from the machine.

 Always place the appliance on a level and firm surface.

3. Operation

1. Place the tile on the cutter bed. Set the guide to the width of the tile.

2. Position the tile-cutter wheel on the base of the tile to be cut.

Score the tile by moving the handle forward away from you while pressing down – –

lightly. K steady pressure for the full length of the tile. eep a

At the end of the score, the wheel will bump against the buffer. Make sure the anvil sits

over the score line.

3. Press down slightly applying increasing pressure until the tile snaps. Tip: Press the handle

with one hand and hold the base of the tile with the other.

PH340/PH360

V. 01 05/12/2018 3 ©Velleman nv –

4. Cleaning and Maintenance

Occasionally wipe with a damp cloth to keep free from dust. Do not use harsh chemicals,

cleaning solvents or strong detergents.

Follow the illustrations below to replace the cutting wheel.

5. Technical Specifications

length

PH340 ........................................................................................................... 400 mm

PH360 ........................................................................................................... 600 mm

max. tile thickness ................................................................................................. 12 mm

PH340 ............................................................................................................ 12 mm

PH360 ......................................................................................................... 4-12 mm

cutting wheel size ........................................................... 22 x 6 x 2 mm (order code PH341)

Use this device with original accessories only. Velleman nv cannot be held

responsible in the event of damage or injury resulting from (incorrect) use of this

device. For more info concerning this product and the latest version of this manual,

please visit our website www.toolland.eu. The information in this manual is subject

to change without prior notice.

The copyright to this manual is owned by Velleman nv. All worldwide rights reserved.

No part of this manual may be copied, reproduced, translated or reduced to any electronic

medium or otherwise without the prior written consent of the copyright holder.

Termékspecifikációk

Márka:	Toolland
Kategória:	vágógép
Modell:	PH360

Szüksége van segítségre?

Ha segítségre van szüksége Toolland PH360, tegyen fel kérdést alább, és más felhasználók válaszolnak Önnek

Az Ön neve*

Az Ön e-mail címe*

Írja ide kérdését

Útmutatók vágógép Toolland

Toolland PH360 Útmutató

8 December 2024

Útmutatók vágógép

Legújabb útmutatók vágógép

Güde GHF 800 Útmutató

8 December 2024

Royal Catering RCKS-3 Útmutató

16 Október 2024

Royal Catering RCKS-2 Útmutató

16 Október 2024

Royal Catering RCAM-250E Útmutató

15 Október 2024

Royal Catering RCAM-250PRO Útmutató

15 Október 2024

Royal Catering RCAM-250EXPERT Útmutató

15 Október 2024

Princess Classic Multi Food Slicer 492977 Útmutató

10 Október 2024

Severin AS 3914 Útmutató

9 Október 2024

Ozito MCS-2355 Útmutató

6 Október 2024

Sunbeam FC7500 Útmutató

5 Október 2024