Használati útmutató TK Audio TK-lizer 2

TK Audio nincs kategorizálva TK-lizer 2

Olvassa el alább 📖 a magyar nyelvű használati útmutatót TK Audio TK-lizer 2 (3 oldal) a nincs kategorizálva kategóriában. Ezt az útmutatót 3 ember találta hasznosnak és 2 felhasználó értékelte átlagosan 4.5 csillagra

Letöltés PDF

Oldal 1/3

www.tkaudio.se

TK-lizer 2

Mastering EQ with M/S function

Thank you for buying the TK-lizer 2, manufactured and hand-assembled in Sweden and

thoroughly tested before leaving the factory.

The TK-lizer 2 is inspired of the Baxandall circuit from the 50’s. It’s a dual three-band EQ with low

and high bands switchable between shelf or peak. It has a high-pass filter with 12dB/oct slope, and

of course a level control for fine adjustments of the output level. To make the EQ even more useful it’s

also equipped with a M/S circuit. All controls are stepped for easy repeatability.

The controls:The controls:

The controls:The controls:The controls:

Low freq: 28Hz, 48Hz, 72Hz, 132Hz, 195Hz, 255Hz, switchable between shelf or peak.

Mid freq: 400Hz, 630Hz, 870Hz, 1.3kHz, 2.4kHz, 4.8kHz.

High freq: 4kHz, 7.2kHz, 12kHz, 16kHz, 20kHz, 25kHz, switchable between shelf or peak.

HPF freq: 20Hz, 25Hz, 30Hz, 35Hz, 40Hz, 45Hz, or 100Hz, 125Hz, 150Hz, 175Hz, 200Hz,

225Hz with the x5 switch activated. 12dB/octave.

Cut/boost: -4dB, -3dB, -2dB, -1dB, -0.5dB, 0dB, +0.5dB, +1dB, +2dB, +3dB, +4dB.

Level: -4dB, -3dB, -2dB, -1dB, -0.5dB, 0dB, +0.5dB, +1dB, +2dB, +3dB, +4dB.

EQ in/out.

M/S in/out.

Cue switch for separate monitoring of the mid or side signal.

M/S mode:M/S mode:

M/S mode:

When you select M/S mode the signal is split into M=mid (L+R) and S=Side (L-R) before the EQ, after

the EQ the signal is decoded back to L and R again.

None of the center information as bass drum, bass and lead vocal is present in the S channel, only

panned signals as guitars, drums, keys etc. In M/S mode you can affect the M and S signal

separately.

By using the high pass filter in M/S mode you can affect the lower range in two ways.

1. HPF on M channel cuts the low energy in the signal. (L and R)

2. HPF on S channel, frequencies below the selected frequency will be in mono. This is used when

cutting records and also to get a more focused low range.

In M/S mode you can also use the level controls to alter the stereo images, more S channel will widen

the image and less S channel will reduce the stereo images.

To be able to hear better what you are doing in M/S mode you can use the M and S cue switch to

listening to the M channel or S channel alone. The cued signal will be feeded to both channels then.

www.tkaudio.se

Low frequency

Shelf or peak mode Mid frequency

Mid cut/boost

Low cut/boost +/-4dB

EQ in/out

M/S function in/out

M or S cue

HPF in/out

HPF frequency x5

www.tkaudio.se

EU - Declaration of conforEU - Declaration of conforEU - Declaration of conforEU - Declaration of conforEU - Declaration of conformity / Överenstämmelseintygmity / Överenstämmelseintygmity / Överenstämmelseintygmity / Överenstämmelseintygmity / Överenstämmelseintyg

ProductProduct

ProductProductProduct

TK Audio TK-lizer 2

115v - 200mA

230v - 100mA

Manufactor / TillverkareManufactor / Tillverkare

Manufactor / TillverkareManufactor / TillverkareManufactor / Tillverkare

Thomas Kristiansson

Musikverkstan / TK Audio

Falkenbergsgatan 10

30233 Halmstad

Sweden