Használati útmutató TDE Instruments Digalox DPM72-MPPA

TDE Instruments Mérőberendezések Digalox DPM72-MPPA

Olvassa el alább 📖 a magyar nyelvű használati útmutatót TDE Instruments Digalox DPM72-MPPA (8 oldal) a Mérőberendezések kategóriában. Ezt az útmutatót 6 ember találta hasznosnak és 2 felhasználó értékelte átlagosan 4.5 csillagra

Letöltés PDF
Oldal 1/8
Digalox DPM72-MPPA
Instruction manual (Rev-2020-09)
Graphical panel meter with RGB backlight for analogue signal 2 × 0/4 - 20 mA
Package contents: Panel meter Digalox DPM72-MPPA, mounting bracket,
5 jumpers, 2 instruction manuals (EN + DE)
1. Safety instructions
•Read instruction manual carefully before operating the device! Keep for later
reference.
•Mounting and installation must be carried out by suitably qualified and competent
persons only.
•When working on the device hazardous voltages must not be connected to
the device! The terminals J1-J12 are not isolated from the measuring
circuit.
•The device must not be used as the only protective device or protective
shutdown.
•The device is not intended to protect persons or facilities against harm. Specific
devices must be used to guarantee safety (protection relays, cut-off switches,
etc.).
•When connecting switches to the terminals J1-J6, only switches must be used
whose isolation voltage is at least twice the maximum occurring measurement
voltage. For example, when measuring 30;V DC switches must be isolated for at
least 60;V.
•Do not open the housing!
•Do not use the device in the presence of explosive or flammable substances!
•All cables carrying hazardous voltages must be secured with external separators.
2. Meaning of symbols
General warning sign
(Attention, observe the documentation!)
Warning of an electrical hazard
----- ----- 1 / 8
3. Intended use
•Measurement of current in the specified measuring range for process signals
•Indoor use non condensing, non corrosive.
•Panel mounting.
•In operation, supply the device preferably via screw terminals with 12 to 24;V
AC/DC. If the device is supplied via USB in operation, USB supply voltage must
be at least 5;V.
•Failure to comply with these instructions will void all guarantee and warranty.
4. Description
The measurement mode analogue signal 0/4 to 20 mA DC is supported at two
measurement inputs. The multi display with RGB backlight is able to display up to
four parameters simultaneously. Thresholds can be associated with individual
warning colours. The unit can be switched between measurement modes via an
external switch. Minimum and maximum values are recorded and can be displayed
and reset via jumper or an external switch. Measured values are recorded over a
timespan of 36 seconds up to 14 days. The timebase as well as the display of the
measuring history can be activated by an external switch. The measured values
remain stored as long as the device is supplied with voltage.
The following parameters can be adjusted using the configuration software “Digalox
Manager”: scale endpoint, scale caption, display style (pointer, tachometer, bar
graph, and more), splash image, backlight colour, thresholds for alarm output,
threshold warning colour (light, blink), hysteresis, and more. Recorded
measurement values can be read and a continuous transmission of the actual
measuring value can be enabled. Using the software, values can be viewed and
exported as CSV. Depending on the model, measured values can be transmitted via
USB, XBEE radio technology or RS485 Modbus interface. In addition, the devices
feature a counting function with data retention. This enables operating-hours-
counters or time-counters for exceeding and falling below threshold values.
Visit to download the software “Digalox Manager”.www.digalox.com
----- ----- 2 / 8
5. Product overview
3
5
4
2
1
2
6
Front
1 Unit or free text
2 Threshold values
3 Upper scale caption
4 Graphical measurement display
5 Digital measurement value
6 Lower scale caption
Digalox DPM72-MPPA
www.digalox.com
Made in Germany
USB
Outputs max.
30 V
50 mA
–
Supply
12 - 24 V
~/
+
Mode 1
Mode 2
Mode 3
Autoscale
Min/Max
Timebase
Bus 1
Bus 2
NC
GPIO 1
GPIO 2
NC
J1
J2
J3
J4
J5
J6
J7
J8
J9
J12
J11
J10
I2low I2high I1high I1low
100 mA max. 100 mA max.
3
2
1
5
4
Back
1 2 optocoupler switch outputs
2 Jumper pins J1–J12
for activating/switching of graphical
historic data display, min/max
display, auto-scaling, measurement
mode
3 Supply voltage input
4 Interface (USB / XBEE / RS485)
5 Measurement inputs
6. Mounting
Carefully insert the device into the panel
cut-out. Insert the mounting bracket from
the back and push towards the panel until
the device sits tight. Make sure the
mounting bracket is snapped into the side
of the housing. To ensure IP65 protection
(dust and water jet) when mounting in a
front panel, use optional gasket
(separately available).
----- ----- 3 / 8
Panel thickness: max. 6 mm
Press mounting
bracket

Termékspecifikációk

Márka: TDE Instruments
Kategória: Mérőberendezések
Modell: Digalox DPM72-MPPA

Szüksége van segítségre?

Ha segítségre van szüksége TDE Instruments Digalox DPM72-MPPA, tegyen fel kérdést alább, és más felhasználók válaszolnak Önnek


Útmutatók Mérőberendezések TDE Instruments

TDE Instruments

TDE Instruments Digalox DPM72-AVP Útmutató

18 Augusztus 2024
TDE Instruments

TDE Instruments Digalox DPM72-MP Útmutató

18 Augusztus 2024
TDE Instruments

TDE Instruments Digalox DPM72-MPP Útmutató

17 Augusztus 2024
TDE Instruments

TDE Instruments Digalox DPM72-MPPA Útmutató

17 Augusztus 2024
TDE Instruments

TDE Instruments Digalox DPM72-MPN Útmutató

16 Augusztus 2024
TDE Instruments

TDE Instruments DPM961 Útmutató

15 Augusztus 2024
TDE Instruments

TDE Instruments Digalox DPM72-AV Útmutató

15 Augusztus 2024

Útmutatók Mérőberendezések

Legújabb útmutatók Mérőberendezések

Uni-T

Uni-T UT220 Útmutató

3 Április 2025
Uni-T

Uni-T UT681C Útmutató

3 Április 2025
Uni-T

Uni-T UT216C Útmutató

3 Április 2025
Uni-T

Uni-T UT611 Útmutató

3 Április 2025
Uni-T

Uni-T UT210D Útmutató

3 Április 2025
Uni-T

Uni-T UT210C Útmutató

3 Április 2025
Uni-T

Uni-T UT210B Útmutató

3 Április 2025
Uni-T

Uni-T UT682 Útmutató

3 Április 2025
Uni-T

Uni-T UT275 Útmutató

3 Április 2025
Uni-T

Uni-T UT08A Útmutató

3 Április 2025