Használati útmutató Swann CoreCam

Olvassa el alább 📖 a magyar nyelvű használati útmutatót Swann CoreCam (32 oldal) a Térfigyelő kamera kategóriában. Ezt az útmutatót 2 ember találta hasznosnak és 2 felhasználó értékelte átlagosan 4.5 csillagra

Oldal 1/32
CoreCam® Security Camera
Cámara de seguridad CoreCam®
Caméra de sécurité CoreCamMD
Telecamera di sicurezza CoreCam®
CoreCam® Überwachungskamera
EN Quick Start Guide ES Guía de inicio rápido FR Guide de démarrage rapide
IT Guida rapida DE Schnellstartanleitung
2
EN
CAMERA OVERVIEW
Threaded screw hole
(attaches to the included wall-mount bracket)
Pull rubber cap gently from the bottom to access:
ON/OFF switch
MicroSD card slot
32GB card pre-installed, Max. 128GB card supported
Micro USB charging port
Reset button
Press and hold for 5 seconds to enter pairing mode
Press and hold for 10 seconds to factory reset the camera
Microphone Speaker
QR code (for
device pairing)
Rubber cap
Passive infrared
motion sensor
LED indicator
Night detection
sensor
Infrared LEDs
(for night vision)
Threaded
mounting post
Bracket screw hole (x3)
Locking knob
3
EN
GETTING STARTED
Before using the camera for the first time, fully charge it with the included micro USB charging cable.
1 Pull open the rubber cap on the bottom of the camera.
2 Slide the switch to the position ON/OFF ON Note: You can also charge the camera with the
switch OFF but you won’t be able to check the LED indicator for the charging status.
3 Insert the smaller end of the micro USB charging cable into the micro USB port on the camera.
4 Insert the other end of the micro USB charging cable into a USB wall charger such as the USB
power adapter for your smartphone.
5 The LED indicator on the front of the camera will turn solid blue indicating that the camera is
charging. When the camera is fully charged, the LED indicator will turn off. Actual charging times
may vary depending on the USB power supply (DC5V 2.1A is recommended for faster charging)
and the remaining battery level. A full charge may take up to 6 hours.
6 After charging is finished, unplug the micro USB charging cable from the camera and make sure
to close the rubber cap tightly to keep out water and dust.
The camera comes with a 32GB microSD card pre-installed for recording events and performing
firmware updates. You can easily replace the microSD card with a new one (max. 128GB card
supported), if needed in the future. Simply open the rubber cap on the bottom of the camera, eject
the current microSD card (push in until it clicks) from the microSD card slot, and then insert the new
microSD card (with the label side facing the front of the camera) into the slot until it clicks into place.
You should format the microSD card the first time it is used. From the Swann Security app, go to
Device Settings > [your camera] > and tap Advanced Settings Format.
Charging the camera
Replacing the microSD card

Termékspecifikációk

Márka: Swann
Kategória: Térfigyelő kamera
Modell: CoreCam

Szüksége van segítségre?

Ha segítségre van szüksége Swann CoreCam, tegyen fel kérdést alább, és más felhasználók válaszolnak Önnek




Útmutatók Térfigyelő kamera Swann

Swann

Swann SW312-HMD-CA Útmutató

16 Szeptember 2024
Swann

Swann PRO-A851 Útmutató

15 Szeptember 2024
Swann

Swann PRO-760 Útmutató

10 Szeptember 2024
Swann

Swann SW231-WMX Útmutató

10 Szeptember 2024
Swann

Swann ADS-466 Útmutató

8 Szeptember 2024
Swann

Swann SWVID-PENBL4 Útmutató

2 Szeptember 2024
Swann

Swann Pro-535 Útmutató

31 Augusztus 2024
Swann

Swann PRO-743 Útmutató

27 Augusztus 2024
Swann

Swann PRO-843 Útmutató

27 Augusztus 2024

Útmutatók Térfigyelő kamera

Legújabb útmutatók Térfigyelő kamera