Használati útmutató StarTech.com PEX10GSFP

StarTech.com hálózati kártya/adapter PEX10GSFP

Olvassa el alább 📖 a magyar nyelvű használati útmutatót StarTech.com PEX10GSFP (2 oldal) a hálózati kártya/adapter kategóriában. Ezt az útmutatót 5 ember találta hasznosnak és 2 felhasználó értékelte átlagosan 4.5 csillagra

Letöltés PDF
Oldal 1/2
Quick-Start Guide
To view manuals, FAQs, videos, drivers, downloads, technical drawings, and more, visit www.startech.com/support.
Manual Revision: March 10, 2022 11:40 AM
Product Diagram (PEX10GSFP)
Component Function
1SFP+ Slot • Connect a 10G SFP+ Transceiver Module to the
PCI Express Card.
2Link/Activity LED
• Solid Green: Network Device A link to a has
been established.
• Flashing Green: Indicates network activity.
3PCI Express Connector
(x4)
• Used to connect the to the PCI Express Card
Host Computer.
• Gen 3 connection.
Package Contents
• Network Card x 1
• Low-Prole Bracket x 1
• Quick-Start Guide x 1
Requirements
For the latest requirements, please visit www.startech.com/PEX10GSFP
• PCI Express enabled computer with an available PCI Express p1-x4 slot
• 10G SFP+ Transceiver Module
1 Port PCI Express 10GbE SFP+ Network Adapter Card
Hardware Installation
Installing the Low Prole Bracket
By default the is attached to the . Depending Full Prole Bracket PCI Express Card
on your system conguration you may need to remove the and Full Prole Bracket
replace it with the (included).Low Prole Bracket
1. Using a , remove the two securing Small Phillips Head Screwdriver Bracket Screws
the to the .Full Prole Bracket PCI Express Card
2. Align the on the with the on theScrew Holes PCI Express Card Screw Holes Low
Prole Bracket PCI Express Card Screw . Making sure the is sitting on-top of the
Holes Low Prole Bracket on the .
3. Insert the through the and into the Bracket Screws PCI Express Card Screw Holes
on the . Low Prole Bracket
4. Using the , tighten the , being Small Phillips Head Screwdriver Bracket Screws
careful not to over-tighten.
Installing the PCI Express Card
Static Electricity PCI Express Cardscan severely damage . Ensure that you are
adequately before you open your or touch the Grounded Computer Case PCI
Express Card Anti-Static Strap Anti-Static Mat . You should wear an or use an when
installing any computer component. If an isn’t available, discharge Anti-Static Strap
any built-up static electricity by touching a large for several Grounded Metal Surface
seconds. Only handle the by its edges and don’t touch the gold PCI Express Card
connectors.
1. Turn o the and any connected to the Host Computer Peripherals Devices
computer (e.g. printers, external hard drives, etc.).
2. Unplug the from on the back of the and disconnect all Power Cable Host Computer
Peripheral Devices.
3. Remove the from the (refer to the documentation that Cover Host Computer Case
came with the for further details).Host Computer
4. Locate an open and remove the metal cover plate on the rear of PCI Express p1-x4 Slot
the (See documentation for your computer system for details).Computer Case
Note: This card will work in of additional lanes (e.g. x8, or x16 PCI Express Slots
slots).
5. Gently insert the into an open and fasten the PCI Express Card PCI Express Slot
Bracket Computer Case to the rear of the .
6. Place the back onto the .Cover Computer Case
1
2
3
FCC Compliance Statement
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC
Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment o and on, the user is encouraged to try to correct the interference by one or more of the
following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit dierent from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including
interference that may cause undesired operation. Changes or modications not expressly approved by StarTech.com could void
the user’s authority to operate the equipment.
Industry Canada Statement
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe [B] est conforme à la norme NMB-003 du Canada.
CAN ICES-3 (B)/NMB-3(B)
This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions:
(1) This device may not cause interference, and (2) This device must accept any interference, including interference that may
cause undesired operation of the device.
Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de licence. L’exploitation
est autorisée aux deux conditions suivantes:
(1) l’appareil ne doit pas produire de brouillage, et (2) l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi,
même si le brouillage est susceptible d’en compromettre le fonctionnement.
Use of Trademarks, Registered Trademarks, and other Protected Names and Symbols
This manual may make reference to trademarks, registered trademarks, and other protected names and/or symbols of third-
party companies not related in any way to StarTech.com. Where they occur these references are for illustrative purposes only
and do not represent an endorsement of a product or service by StarTech.com, or an endorsement of the product(s) to which
this manual applies by the third-party company in question. StarTech.com hereby acknowledges that all trademarks, registered
trademarks, service marks, and other protected names and/or symbols contained in this manual and related documents are the
property of their respective holders.
Warranty Information
This product is backed by a two-year warranty.
For further information on product warranty terms and conditions, please refer to .www.startech.com/warranty
Limitation of Liability
In no event shall the liability of StarTech.com Ltd. and StarTech.com USA LLP (or their ocers, directors, employees or agents)
for any damages (whether direct or indirect, special, punitive, incidental, consequential, or otherwise), loss of prots, loss of
business, or any pecuniary loss, arising out of or related to the use of the product exceed the actual price paid for the product.
Some states do not allow the exclusion or limitation of incidental or consequential damages. If such laws apply, the limitations
or exclusions contained in this statement may not apply to you.
Safety Measures
• If product has an exposed circuit board, do not touch the product under power.
Mesures de sécurité
• Si l’un des circuits imprimés du produit est visible, ne pas touchez le produit lorsqu’il est sous tension.
安全対策
•  製品に露出した状態の回路基盤が含まれる場合、電源が入っている状態で製品に触らないでください。
Misure di sicurezza
• Se il prodotto ha un circuito stampato visibile, non toccare il prodotto quando è acceso.
Säkerhetsåtgärder
• Rör aldrig vid enheter med oskyddade kretskort när strömmen är påslagen.
FR: startech.com/fr
DE: startech.com/de
ES: startech.com/es
NL: startech.com/nl
IT: startech.com/it
JP: startech.com/jp
StarTech.com Ltd.
45 Artisans Crescent
London, Ontario
N5V 5E9
Canada
StarTech.com Ltd.
Unit B, Pinnacle 15
Gowerton Road
Brackmills,
Northampton
NN4 7BW
United Kingdom
StarTech.com LLP
4490 South Hamilton
Road
Groveport, Ohio
43125
U.S.A.
StarTech.com Ltd.
Siriusdreef 17-27
2132 WT Hoofddorp
The Netherlands
7. Insert the of your choice, compatible with your 10G SFP+ Transceiver Module
network, into the on the .SFP+ Slot PCI Express Card
8. Insert the into the socket on the power supply and reconnect all other Power Cable
connectors removed in .Step 1
Note: The 10G ber card is compatible with transceiver modules only.10G SFP+
Driver Installation
When the is installed the drivers should install automatically. If the PCI Express Card
drivers do not automatically install, follow the next steps.
1. Navigate to www.startech.com/PEX10GSFP
2. Click the tab.Drivers/Downloads
3. Under , download the for your operating system.Driver(s) Driver
4. Extract the contents of the package. Follow the on-screen instruction of the Driver
Installer Package Driver to nish installing the .
Connecting to a Network
1. Insert a compatible , into the on the 10G SFP+ Transceiver Module SFP+ Slot PCI
Express Card.
2. Connect a or to the Fiber Network Cable Cat5e/6 Cable 10G SFP + Transceiver Module
and the other end to a or on a 10G Fiber Port RJ45 Port Network Device.

Termékspecifikációk

Márka: StarTech.com
Kategória: hálózati kártya/adapter
Modell: PEX10GSFP

Szüksége van segítségre?

Ha segítségre van szüksége StarTech.com PEX10GSFP, tegyen fel kérdést alább, és más felhasználók válaszolnak Önnek


Útmutatók hálózati kártya/adapter StarTech.com

StarTech.com

StarTech.com 107B-USB-HDMI Útmutató

15 Január 2025
StarTech.com

StarTech.com USB32HDVGA Útmutató

15 Január 2025
StarTech.com

StarTech.com ST1000SPEXD4T Útmutató

10 Január 2025
StarTech.com

StarTech.com U1-USB-ISOLATOR Útmutató

30 December 2025
StarTech.com

StarTech.com AX54005A-USB-WIFI-6E Útmutató

30 December 2025
StarTech.com

StarTech.com O1210I-NETWORK-CARD Útmutató

29 December 2024
StarTech.com

StarTech.com CDP2DVI Útmutató

29 December 2024
StarTech.com

StarTech.com ST1000SPEXD2 Útmutató

29 December 2024
StarTech.com

StarTech.com OR41GI-NETWORK-CARD Útmutató

17 December 2024
StarTech.com

StarTech.com ST1000SPEX2T Útmutató

3 Október 2024

Útmutatók hálózati kártya/adapter

Legújabb útmutatók hálózati kártya/adapter

Mikrotik

Mikrotik RB493 Útmutató

8 Április 2025
EtherWAN

EtherWAN EX41941F Útmutató

3 Április 2025
Vigitron

Vigitron MaxiiView Vi00023 Útmutató

3 Április 2025
AVPro Edge

AVPro Edge AC-MXNET-10G-TCVR Útmutató

2 Április 2025
EtherWAN

EtherWAN TG103H-0802 Útmutató

2 Április 2025
AVPro Edge

AVPro Edge MXNet AC-MXNET-10G-TCVR Útmutató

1 Április 2025
ScreenBeam

ScreenBeam ECB6250 Útmutató

30 Március 2025
Ubiquiti Networks

Ubiquiti Networks USW-Aggregation Útmutató

29 Március 2025
Vigitron

Vigitron Vi22601 Útmutató

15 Március 2025
Vigitron

Vigitron Vi22201 Útmutató

15 Március 2025